Panasonic Palmcorder Palmsight PV-L958 User manual

Panasonic’
Palmcorder® PalmSight”
Camcorder
Operating Instructions
VHSIA
PV-L958
Please read these instructions carefully before attempting to operate this product. Please save this manual,
Spanish Quick Use Guide is included.
Guía para rápida consulta en espanol está incluida. O

Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most sophisticated and reliable products on the market
today. Used properly, it will bring you years of enjoyment. Please take time to fill in the
information below. The serial number is on the tag located on the underside of your
Camcorder. Be sure to retain this manual as your convenient Camcorder information
source.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Seríal No.
Unpack your Camcorder
These accessories are provided in order to set up or use your Camcorder.
1 pc. AC Adaptor 1 pc. Battery Pack 1 pc. Audio/Video 1 pc. VHS PlayPak
(PV-A17) (PV-BP18) Cable (VJAW0039} (PV-P1/VYMWO009)
with DC Power Cable (see pages 9, 10) (see pages 31, 51) and one “AA” battery
(see page 11) (see page 32)
Ea
K 2
1 pc. Shoulder Strap 1 pc. Remote Control 1 pc. PC Connection 1 pcs. Driver
(VYCW0149) Holder (VGQ6893) ^ cable (RS232C-3P) Software Floppy Disk
(see page 21) (see pages 21, 28) (LSJA0185/LSJA0190) for Windows 95
(see page 58) (VFTWOO06)
(see page 59)
LF
1 pc. CR2025 Clock — 1 pc. 8-Function Remote 1 pc. Wiping Cloth
Battery (VSBW0004) | (V8QWOO0538) with one (VFCWO001)
(installed in CR2025 Battery
Camcorder)
(see page 17) ~
e
l Use this wiping cloth to clean
Remote has been loaded with the display screen of finger
battery,
(see
page
28)
prints
and
other
smudges.

Things You Should Know
Safety Precautions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
Your Compact VHS Camcorder is designed to record and play back in Standard Play
(SP) and Super Long Play (SLP) modes. You can also play a Compact VHS
Camcorder recording on your VHS VCR using the VHS PlayPak supplied.
This Camcorder is equipped with the HQ System to provide excellent video pictures,
and is compatible with standard VHS equipment.
It is recommended that only cassette tapes that have been tested and inspected for use
in VCR machines with the MIÐ and/or mark be used.
G)
D
=
5
a
o
puts
S
c
D
o.
This symbol wams the user that
uninsulated voitage within the unit may
k aoe N have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make
any kind of contact with any inside part of
this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK) This symbol alerts the user that important
NO USER-SERVICEABLE PARTS INSIDE literature concerning the operation and
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL maintenance of this unit has been included.
Therefore, it should be read carefully in
order to avoid any problems.
The above markings are located on the appliance bottom cover.
FCC Warning: To assure continued FCC compliance, the user must use only
provided shielded interfacing cable with ferrite cores when connecting
to computer. Also, any unauthorized changes or modifications to this
equipment would void the users authority to operate.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two con-
ditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital de-
vice and a RF Lighting device, pursuant to part 15 and Part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is `
connected.
-- Consult the dealer or an experienced radio/TV technician for help.

Important Safeguards
10.
Read Instructions — All the safety and operating
instructions should be read before the unit is
operated.
Retain Instructions — The safety and operating
instructions should be retained for future reterence.
Heed Warnings — All warnings on the unit and in
the operating instructions should be adhered to.
Follow Instructions — All operating and
maintenance instructions should be followed.
Cleaning — Unplug this video unit from the wall
outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a dry cloth for cleaning.
Attachments — Do not use attachments not
recommended by the video product manufacturer
as they may be hazardous.
Water and Moisture — Do not use this video unit
near water — for example near a bath tub, wash
bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like.
Accessories — Do not place this video unit on an
unstable cart, stand, tripod, bracket, or table, The
video unit may fall, causing serious injury to a child
or adult, and serious damage to the unit. Use only
with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the
video unit. Any mounting of the unit should follow
the manufacturer's instructions and should use a
mounting accessory recommended by
the manufacturer. An appliance and
cart combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart
combination to overturn.
Ventitation — Slots and openings in the cabinet are
provided for ventilation and to ensure reliabla
operation of the video unit and to protect it from
overheating. These openings must not be blocked
or covered. Never place the video unit on a bed,
sofa, rug, or other similar surface, or near or over a
radiator or heat register. This video unit should not
be placed in a built-in instatlation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have
been adhered to.
Power Sources — This video unit should be
operated only from the type of power source
indicated on the marking label. If you are not sure
of the type of power supply to your home, consult
your appliance dealer or local power company. For
video units intended to be operated from battery
power, or other sources, refer to the operating
instructions.
11. Grounding or Polarization — This video unit may
be equipped with either a polarized 2-wire AC
(Alternating Current) line plug (a plug having one
blade wider than the other) or 3-wire grounding
type plug, a plug having a third (grounding) pin.
The 2-wire polarized plug will fit into the power
outlet only one way. This is a safety feature. if you
are unable to insert the plug fully into the outlet, try
reversing the ptug. If the plug still fails to fit, contact
your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
The 3-wire grounding type plug will fit into a
grounding type power outlet. This is a safety
feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of
the grounding type plug.
12. Power-Cord Protection —- Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them. Paying particular attention to cords of
plugs, convenience receptacles, and the point
where they exit from the unit.
13. Outdoor Antenna Grounding — If an outside
antenna or cable system is connected to the video
unit, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Part 1 of
the Canadian Electrica! Code, in USA Section 810
of the Nationa! Electrical Code, provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-201
ELECTRIC
SERVICE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
Le
POWER SERVICE GROUNDING
T ELECTRODE SYSTEM
NEC — NATIONAL ELECTRICAL COOE (NEC ART 250, PART H)
14. Lightning — For added protection of this video unit
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it frorn the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the video unit due to lightning and power-line
surges.

Important Safeguards
15. Power Lines — An outside antenna system should b. If any liquid has been spilled onto, or objects
not be located in the vicinity of overhead power have fallen into the video unit.
lines or other electric light or power circuits, or c. If the video unit has been exposed to rain or
where it can fall into such power lines or circuits. water.
When installing an outside antenna system, d. If the video unit does not operate normally by
extreme care should be taken to keep from following the operating instructions. Adjust only
touching such power lines or circuits as contact those controls that are covered by the operating
with them might be fatal. instructions, as an improper adjustment of other
16. Overloading — Do not overload wall outlets and controls may result in damage and will often
extension cords as this can result in a risk of fire or require extensive work by a qualified technician
electric shock. to restore the video unit to its normal operation.
17. Objects and Liquids — Never push objects of any e. If the video unit has been dropped or the cabinet
kind into this video unit through openings as they has been damaged.
may touch dangerous voltage points or short out t. When the video unit exhibits a distinct change in
parts that could result in a fire or electric shock. performance — this indicates a need for service.
Never spill liquid of any kind onto the video unit. 20. Replacement Parts — When replacement parts are
18. Servicing — Do not attempt to service this video required, be sure the service technician has used
unit yourselt as opening or removing covers may replacement parts specified by the manufacturer or
expose you to dangerous voltage or other hazards. have the same characteristics as the original part.
Refer all servicing to qualified service personnel. Unauthorized substitutions may result in fire,
19. Damage Requiring Service — Unplug this video electric shock or other hazards.
unit
from
the
wall
outlet
and
refer
servicing
to
21.
Safety
Check—
Upon
completion
of
any
service
or
qualified service personnel under the following repairs to this video unit, ask the service technician
conditions: to perform safety checks to determine that the
a. When the power-supply cord or plug is video unit is in safe operating order.
damaged.
Precautions
USE & LOCATION
* TO AVOID SHOCK HAZARD ... Your Camcorder and power supply should not be exposed to rain or moisture.
Do not connect the power supply or operate your Camcorder if it gets wet. Your Camcorder has been designed
for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or
a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts
of your Camcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug
your Camcorder from the power supply before cleaning.
* DO NOT AIM YOUR CAMCORDER AT THE SUN OR OTHER BRIGHT OBJECTS.
* DO NOT LEAVE THE CAMCORDER WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF THE EVF.
* DO NOT EXPOSE YOUR CAMCORDER TO EXTENDED HIGH TEMPERATURE ... Such as, in direct sunlight,
inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your
Camcorder.
* AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm
place, moisture may form on the tape and inside the unit.
* DO NOT LEAVE YOUR CAMCORDER OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.
* STORAGE OF YOUR CAMCORDER ... Store and handle your Camcorder in a manner that will not subject it to
unnecessary movement (avoid shaking and striking). Your Camcorder contains a sensitive pick-up device which
could be damaged by improper handling or storage.
CARE
* TO CLEAN YOUR CAMCORDER ... Do not use strong or abrasive detergents when cleaning your Camcorder
body.
* TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial camcorder
lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.
* TO PROTECT THE FINISH OF YOUR CAMCORDER ... Before handling your Camcorder, make sure your
hands and face are free from any chemical products, such as suntan lotion, as it may damage the finish.
peuejs Buas

Table of Contents
Getting Started
Things You Should Know ........................... MINI A nd 2
Important Safeguards .................... sse T —— M TE sasi
Precautions ............. D E OET SON E EEE PO IAEA evn
Self Demo Mode ........... ON EE TONER HORA Peu HN KE MES 7
Quick Operation Guide ........................ nsus iude n su. DOES ROME «deua Seni i
Supplying Power ............................ RS O O is 9
Cassette Information sese eee e ias 12
0201581 ar T E
Setting the e e Qu —— m 14
Electronic Viewfinder/LCD Monitor Indications ..................... NTC S a 18
Attaching the Shoulder Strap and Remote Control Holder sese 21
Built Auto Cin ist apte ce Rodas ee AS .. 22
Basic Operation
Camera: Recordin gesaat Ar rd tete A 23
8-Function Remote Control... e eee 28
Playing Back your Recordings ................... esee EEE RE ET 29
Special Features
Four-Speed Power Zoom sss esse eee ee eee A re 33
Backlight .............. A . 33
FOCUS EM O A E A ON EN 34
High Speed Shutter ....................... A E E E 35
FAO DETUR tata cita — — 36
(llela BI a Clg eec IPC rtm 38
Digital Zoom cxi ee eee ee A dps esa dand 39
Digital Electronic Image Stabilization System ................................... m Me. ... 40
Still / Strobe / Wide .................... D T CREE 41
Digital Wipe ......... ET vende p ruins e LL C Re ta Sk ED EIE UE 0... 42
Security Mode... sese see —— A TENTE TT FN 43
Audio Sensitivity sorses eisdem nte La es 44
Time Lapse uc iden A ee A — E 45
Tally Lamp coria T A E E EE 46
Intelligent Ter: o re es 7
Message Mode sss sese RTT TT 50
Copying your Tapes (dubbing) .20..... eee eee 51
Using the Digital Still Camera sese eee eee eee ee 52
PLE GON OCU ON a. o neo tecto A A ees AT A 58
For Your Information
Palmcorder Accessory System ............ rH UR MERE 61
Palmcorder Accessory Order Form ............................. p RE ENTERS — —— 62
Notes Regarding Operations :.. 5: ossi oss hates paces e te Secr dose dsqi SE Ad ive ii » 63
SCC INCAS A asco A arate S A E DUAE 2. 64
Before Requesting Service ................. C E e 65
Request for Service Notice ......... cd n Lit d eL iM DI I d n NU A ..66
Index of Controls ......................... e Tu NOE ER ERE 67
GON app Mole eria n jt EMT Mum wile
Warranty- ee PC Re |
Spanish Quick Use Guide/Guia Para Uso Rapido. TU pcs
6

Self Demo Mode
If the screen at right appears in the
EVF/LCD Monitor, the Self Demo mode
is on. To turn it off, please follow the EVF Screen
steps below.
Panasonic
ITS VHS!
SO ITS TAPES PLAY
IN YOUR VCR
23x HI-DEFINITION LENS
300x 50x DIGITAL ZOOM
DIGITAL STABILIZATION
DEDICATED 5-HEAD
DIGITAL PHOTOSHOT
1 Set the POWER switch to CAMERA.
2 Hold down the STOP button for more
than 5 seconds.
Note:
* The Self Demo mode will automatically
turn itself off if a battery is attached
(see page 9) and a cassette tape is
inserted (see page 12).
* Inserting a tape alone (or attaching a
partially charged battery ) will only
temporarily turn the Self Demo mode off.
* The Self Demo mode will temporarily stop
for 30 seconds when a function key other
than Power, Tape Speed Selector, Light,
Message, and Digital Select is pressed.
To turn the Self Demo mode on, follow
the steps below.
* With the DISPLAY button held down, slide
the POWER switch to CAMERA and wait
for the Self Demo screen to appear in the
EVF/LCD Monitor.
7
paiupie Bua

Quick Operation Guide
Camera Recording
Charge the Battery Pack fully before operation (see page 9).
(—_ SpE
a I Attach a fully charged Battery
9 (see page 9).
d
1
Slide
the
TAPE
EJECT
switch
to
open
door.
3 Insert cassette (see page 12).
E NR here to close door.
5 Set POWER switch to CAMERA.
Built-In Lens Cover opens and POWER
Lamp lights.
O siae TAPE SPEED Selector to SP or
SLP (see page 12).
POWER | | |
Samp Caria looking into the Viewfinder,
adjust the Vision Adjustment Control
to your eyesight.
8 Press RECORD/PAUSE to start
recording.
Press RECORD/PAUSE again to
pause recording (see page 23).
1 Set the POWER switch to VCR.
ai] | 2 Press the REWIND/SEARCH to rewind
lape.
K Press PLAY to start playback.
Z cus STOP to stop playback.

Supplying Power
Charge the Battery Pack
Charge the Battery Pack fully
before operation.
Q)
(Œ
m:
=
Q
o
Lea
RM
S)
D
o
1 Plug in the AC Adaptor.
POWER Lamp lights.
Insert the Battery
(& Align the right side of the Battery with
the line on the AC Adaptor.
(B Press the Battery down and slide it in
the direction of the arrow.
CHARGE Lamp lights. When charging is
done (about one and a half hours) the
lamp goes out.
3 Remove the Battery
Slide the Battery out and lift up.
Note:
After recharging the Battery Pack about 5 times, — * The useful operation time of the Battery will
use the BATTERY REFRESH feature as gradually decrease after repeated use and
explained on page 10. recharging. The Battery is no longer
serviceable if the operation time is very short,
even after a sufficient charge.
Use the Battery Pack
With a fully charged Battery Pack, you will have a maximum of about 1.8 hours of
continuous use (LCD monitor is off) or about 1 hour of continuous use (LCD monitor is
on). (The actual operating time may vary due to operation conditions. If the Built-in Light
is used, battery operating time decreases.)
(& Align the Battery with the top of the
mounting surface.
(B) Press it into place until it locks with a
Y click.
(
SS
I
Attach
the
Battery
U
2 Remove the Battery
While sliding the BATTERY RELEASE
A button, remove the Battery.
9

Supplying Power
Battery Refresh Feature
This feature completely discharges the Battery before recharging begins.
To maintain your Battery's operating capacity, use the refresh feature after about every five charges.
CHARGE Lamp
I Plug in the AC Adaptor.
s The POWER Lamp remains lit as long as the
AC Adaptor is plugged in.
2 Place the Battery into
the AC Adaptor.
N pies the BATTERY REFRESH
button.
The CHARGE Lamp flashes until
discharge is complete and then stays lit
until the Battery is fully charged.
4 Remove the Battery.
* Should you accidentally press the BATTERY
REFRESH button, remove the Battery and
then re-insert it to begin charging.
* It takes about 7 and a half hours when both
Battery Refresh and recharging are
erformed.
Battery Care i
Caution: To avoid damage to the Battery:
* Charge only with specified charger. * Do not drop or jar Battery.
* Battery can be charged within a temperature * Use Battery with specified units only.
range of 50? F (10? C) and 95° F (35? C). * If Battery is used in extremely high
* Battery may be warm after charging or just temperatures, a safety device will
after use. This is normal. automatically prevent operation.
* Do not use an insufficiently charged or worn-
Gut Battery: To prolong battery life:
* While not in use, remove Battery from the
Camcorder and AC Adaptor and store in a
cool, dark, dry place.
* Keep Battery terminals clean.
Safety precautions:
* Do not get the Battery near, or dispose of in
fire.
* Do not directly connect (short circuit) the
positive (+) and negative (-) terminals.
* Never attempt to disassemble or reassemble
the Battery.
U.S.A. CONSUMERS:
ATTENTION:
The product you have purchased is powered by a nickel cadmium battery which is
recyclable. At the end of its useful life, under various state and local laws, it is illegal to
dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY
Md — for information on how to recycle this battery.

Supplying Power
AC Adaptor
pouels Humay
DC Power Cable
DC IN 1 Connect VCR DC OUT on the
Connector AC Adaptor to DC IN on the
Camcorder with the DC Power
Cable (supplied).
POWER Lamp
Plug in the AC Adaptor.
VER Oe OUT Connector + The POWER Lamp will fight.
Notes:
* AC Adaptor cannot be used to power the Camcorder while charging the Battery.
* While not in use, unplug the AC Adaptor from the AC outlet. (When plugged into an AC outlet, the
AC Adaptor consumes 1.2W of electric power when not in use.)
C
I Connect a PV-C16 Car Battery Cord
(optional) to DC IN on the Camcorder.
[et First, start your car engine, and then
DC IN í insert the Car Battery Cord plug into
: your cigarette lighter socket.
* A fuse is located in the lighter plug end of
the cord.
Should fuse replacement be necessary
use the exact current rating (in amps).
Notes:
* This cord can only be used in vehicles
equipped with DC 12V (negative ground)
batteries. Use only the specified car battery
cord. If you are not sure, check with your local
car/truck dealer.
* To avoid blowing the fuse, be sure to start your
car engine before inserting the cigarette lighter
plug of the Car Battery Cord into the lighter
Socket.
Cigarette Lighter
Socket (12V)
Car Battery Cord Cigarette
(optional) Lighter Plug * Because the car is running while your
Camcorder is in operation, make sure
you're in a well ventilated area.
* Disconnect the cigarette lighter plug when
your Camcorder is not being used.
11

Cassette Information
Cassette Insertion/Removal
1 Turn the Tape Wheel in the direction
of the arrow until there is no slack.
2 Attach the Battery (see page 9).
p- ae
d Do
e) side the TAPE EJECT switch to open
the door.
74 usan the cassette vertically with its
window side facing out.
5 Press here to close the door.
* To remove the cassette, slide the TAPE EJECT switch.
Record/Playback Time
Use tapes with the [YHSIM mark in this unit.
Tape Speed Selector Cassette type
SLP (Super Long Play) 1 hour 1 hour
30 minutes
* SLP may have slightly more picture noise during playback.
Erase Protection Tab
Cassettes have a record tab to ensure that recordings are not accidentally erased.
TAPE SPEED Selector
1 To prevent accidental erasure,
break off the tab with a screwdriver.
(If slide type, slide tab open.)
2 To record again,
cover the hole with adhesive tape.
(If slide type, slide tab closed.)

MENU Mode Setting
--- MENU --- PAGE 1/2
LAM ; ON
STAND-BY RELEASE ; OFF
STOCK DET
SELECT: PUSH W/A KEY
SET : PUSH DISPLAY KEY
END : PUSH MENU KEY
--- MENU --- PAGE 2/2
A
TIME LAPSE ; OFF
SELECT: PUSH V/A KEY
SET : PUSH DISPLAY KEY
END : PUSH MENU KEY
MENU Mode
Before you begin...
* Connect the Camcorder to a power source.
* Set the POWER switch to CAMERA.
1 Press the MENU button to display
the MENU mode.
CLOCK SET
¥
SELECT: PUSH W/a KEY
SET : PUSH DISPLA
> PUSH MENU KEY
2 Press UP A or DOWN ¥ repeatedly
to select a menu item.
3 Press the DISPLAY button to set your
selection.
Zu the MENU button to exit the
Menu mode.
Note:
* The Camcorder will exit the Menu mode if,
after activation, none of the UP/IDOWN(A/V),
DISPLAY, or MENU buttons are pressed
within 5 minutes.
(D PROGRAMMED REC (see page 27).
You can program the Camcorder to
start and stop recording at a preset
time.
(2) TITLE (see pages 47-49).
AUTO/MANUAL : 16 items
PHRASE : 10 items
(3) TALLY LAMP (see page 46).
The Tally Lamp comes on during
recording when set to ON.
(4) STAND-BY RELEASE (see page 25).
To resume recording from Stand-by
mode, when set to ON.
© CLOCK SET (see pages 14-16).
To set the clock, select CLOCK SET.
(6) TIME LAPSE (see page 45).
To set the TIME LAPSE, when
set to ON.
13
C)
(D
=
-
(©
o
+
£D
=i
(D
¡o

Setting the Clock
Setting the clock is divided into four sections: Time Zone, Daylight Saving Time, Date
and Time, and Clock Battery. Follow instructions in the order presented.
Setting the Time Zone Before you begin...
* Connect the Camcorder to a power source.
The Camcorder is set to Eastern time * Set the POWER switch to CAMERA.
zone at the factory. If you live, or are Note:
traveling, in a different time zone, follow +. When the POWER switch is set to VCR. the
the steps to select the appropriate time CLOCK SET menu will be displayed.
zone from the menu screen. * The Camcorder's clock may lose or gain up
to two minutes per month. Please adjust as
necessary (refer to page 16).
1 Press the MENU button to display
the MENU mode. Press UP A or
DOWN Y a to select
¥
SELECT: PUSH V/A KEY
SET — : PUSH Y
END : PUSH MENU KEY
2 Press the DISPLAY button to display
the CLOCK SET menu. Press UP A or
DOWN Y qo to select
+++ CLOCK SET ---
; EASTERN
T ; AUTO b. S. T. : AUT!
DATE/TIME ; 12:00: 00AM
JAN 1 1
Press the DISPLAY button to display
the SELECT TIME ZONE menu. Press
UP A or DOWN Y repeatedly to
select desired time zone.
--- SELECT TIME ZONE ---
ATLANTIC PACIFIC
SELECT: PUSH Y/A KEY
SET : PUSH DISPLAY KEY|
E ss the DISPLAY button to fix the
NE ae oe A ; Time Zone. The CLOCK SET menu
i $00 9:00 10:00) 11:00 12:00 1:00 32:00 appears. Press the MENU button to
Note:
display
the
MENU.
When
you
travel
outside
the
eight
time
zone
To
exit
from
the
MENU
mode,
press
chart
above,
please
set
the
clock
manually
the
MENU
button.
{see page 16).
14

Setting the Clock
Setting the Daylight Saving Time
The clock will automatically adjust to daylight saving time.
Before you begin...
* Connect the Camcorder to a power source.
* Set the POWER switch to CAMERA.
Note:
* When the POWER switch is set to VCR, the
CLOCK SET menu will be displayed.
The Camcorder is preset to Daytight
EMITE AUTO RIETI OIRE
the clock to be automatically adjusted to
daylight saving time, please select OFF
by following steps 1-4.
* Daylight saving time feature will not function
if time zone is set to Hawaii or Samoa.
1 Press the MENU button to display the
MENU mode. Press UP A or DOWN Y
repeatedly to select[eWe]A El3N.
SELECT: PUSH V/a KEY
SET ; PUSH DISPLAY KEY
END ; PUSH MENU KEY
9 2 raas the DISPLAY button to display
the CLOCK SET menu. Press UP A or
DOWN Y repeatedly to select EMEA.
-- CLOCK SET ---
TIME ZONE ; EASTERN
; AUTO
DATE / TIME ; 12:00: 00AM
JÀN 1 1998
SELECT: PUSH Y/A KEY
: PUSH DISPLAY KEY
END : PUSH MENU KEY
Press the DISPLAY button to display
the DAYLIGHT SAVING TIME menu.
Spring (First Sunday in April): Press UP A or DOWN Y to select
In DAYLIGHT SAVING TIME: AUTO mode, AUTO or OFF.
the clock is automatically moved ahead one
hour.
* - DAYLIGHT SAVING TIME - -
Normal Time pe 2:00 a.m.
Daylight Saving CE 4
Time 3:00 a.m. 4:00 a.m. Press the DISPLAY button to fix the
OFF
SELECT: PUSH V/A KEY
SET : PUSH DISPLAY KEY
Autumn (Last Sunday in October): DAYLIGHT SAVING TIME setting.
In DAYLIGHT SAVING TIME: AUTO mode, The CLOCK SET menu appears.
the clock is automatically turned back one Press the MENU button to display the
hour. MENU.
ligh a 1:00 a.m. 2:00 a.m. l .
Daylight Saving To exit from the MENU mode, press
dime : the MENU button.
TRG
1:00 a.m. 2:00 a.m.
15

Setting the Clock
NKITIIPTPELTENPUTTETYTEITPYM Before you begin...
* Connect the Camcorder to a power source.
The date and time are calculated, including < Set the POWER switch to CAMERA.
leap year, up to DEC 31 2096.
slz
PAM ca 0
JAN
o
19
98
Note:
* When the POWER switch is set to VCR, the
CLOCK SET menu will be displayed.
1 Press the MENU button to display
the MENU mode. Press UP A or
DOWN ¥ ann to select
S T.
TALLY LAMP ` ; ON
STAND-BY RELEASE : OFF
CLOCK SEL]
SELECT; PUSH Y/A KEY
SET : PUSH DISPLAY KEY
END : PUSH MENU KEY
2 Press the DISPLAY button to display
the CLOCK SET menu. Press UP 4
or DOWN Y repeatedly to select
DATE/TIME
-- CLOCK SET ---
TIME ZONE ; EASTERN
D. S. T.
OATES TIMER 12: MA 00AM
Dou the DISPLAY button to display
the DATE/TIME SETTING menu.
ME iip
Az. 00: 08AM
JAN 1 1998
SELECT: PUSH V/A KEY
SET : PUSH DISPLAY KEY,
ts
M-
AS
4 Press UP A or DOWN Y repeatedly
(or hold down) to enter the desired
numbers, then press the DISPLAY
button to fix that portion and move on.
Adjust the flashing digits for the hour,
minute, month, day, and year.
When you finish setting the year, the
clock starts operating, and the CLOCK
SET menu appears.
Press the MENU button to display the
MENU.
To exit from the MENU mode, press
the MENU button.

Setting the Clock
Replacing the Battery
The date and time operates on a miniature
battery preinstalled in the underside of your
Camcorder.
pull the Battery Tray out of the
Battery Compartment.
j While pinching the stopper tabs,
Underside View
2 Remove the Battery by bending
@ O the locking tab outward.
ES
3 Place the new Battery into the
Battery tray with the ® mark facing
down. Press down until it snaps into
place.
* Do not reverse the polarity.
E aes the Battery Tray until both
triangle marks meet.
Note:
* Make sure your Camcorder is off when
replacing the Battery.
* Keep the Battery out of the reach of
children as swallowing it may be harmful.
* Improperly installed, discharged, or
missing battery will cause “CLOCK
BATTERY” to appear when the DISPLAY
button is pressed.
* Battery life is approximately 5 years.
WARNING:
Replace battery with Panasonic PART NO.
VSBW0004 (CR2025) only. Use of another
battery may present a risk of fire or explosion.
Caution-battery may explode if mistreated.
Dispose of used battery promptly. Keep away
from children. Do not recharge, disassemble or
dispose of in fire.
17

Electronic Viewfinder/LCD Monitor Indications
Tape/Battery Remaining
The tape remaining and battery charge level can be displayed during recording.
1 Set the POWER
switch to CAMERA.
2 Press DISPLAY repeatedly
to select the desired display.
EVF/LCD Monitor Indications
Battery Charge Tape
Remaining: Remaining:
-Bd- (No tape)
FULL MEER G ma FULL
ENRO OG) NEN
12:004M
JAN 1 1598
aA&— = v Fourt t Second
EMPTY Bd — press press
ES -hd- EMPTY <== e Third
* It will take several seconds for the tape press
remaining indicator to operate after the
tape starts moving.
Recording the Date and Time
1 Set the POWER 2 press DISPLAY
switch to CAMERA. "sma aez sP twice to change
When placed in REC the display to date
only. Press once
or twice more to
remove the date/
time display.
Record mode, the
time and date will be
recorded on the
tape.
Note:
Only the Date and/or Time indications are recorded on the Tape.
Display-Off Mode
This feature allows you to remove all Electronic Viewfinder/LCD
Monitor Indications except Intelligent Titler (see pages 47-49).
Before inserting a tape, press DISPLAY and STOP together
for more than one second to remove the indications except
time and date".
To display the Indications again, turn the Camcorder Power IRN,
off and then on again.
* To remove the time and date, press the DISPLAY button
repeatedly.
18

Electronic Viewfinder/LCD Monitor Indications
EIS @
c ©
VCR-MODE
WIDE
12:00:00AM
AN 1 1998
(D Battery Remaining Indication Xx 3: (see page 18):
When a battery recharge is necessary, “WARNING LOW BATTERY” will
appear in the EVF. The external Power Lamp will start to flash and the
Camcorder will automatically turn OFF in 15 seconds.
@ Tape Remaining Indication
* If the Camcorder is in the camera mode (RECORD), with no cassette tape
inserted, or the record tab is missing, “les” will flash for one minute and
"CHECK TAPE?’ will appear for 5 seconds.
» As the tape reaches the end during recording, “ESF will flash and “TAPE
END" will appear for 5 seconds as a warning.
(3 10-Second Reminder
An elapsed time indicator appears one second for every 10 seconds that
recording continues. This is a reminder of how long you have been shooting a
particular scene and can help keep your recordings fresh and interesting.
0:00 0:10 0:20 ..... 59:50
A) * The 10-Second Reminder will reset to 0:00
(return to 0:00 and continue) whenever you press the RECORD/PAUSE
button.
@ TAPE SPEED Indication (see pages 12, 45)
Indicates the tape speed (SP or SLP or T.LAPSE).
© Operating Mode Indications
REC (record)
(Appears in large then small characters.)
PAUSE
(Appears in large then small characters.)
FF (fast forward)
PLAY
REW (rewind)
19

Electronic Viewfinder/LCD Monitor Indications
6S PSO ©
(6 Zoom Magnification level (see page 33).
@ Digital E.1.S. Indication (see page 40).
Digital Wipe Indication (see page 42).
(9) Digital Zoom Indication (see page 39).
@ Negative/Positive Indication (see page 38).
@ Still/Strobe Indication (see page 41).
(3 VCR-MODE Indication
Appears for one minute if the POWER switch is set to VCR or the RECORD/PAUSE
button is pushed in VCR MODE.
(3 DEW Indication
If excessive moisture condenses in the unit, “WARNING DEW DETECTED" will
appear, Power Lamp will flash, and the Camcorder will automatically turn OFF in 15
seconds.
Wait until the indicator no longer flashes when your Camcorder is turned on before
use.
(3 Time Lapse Indication (see page 45).
(5 Security Mode Indication (see page 43).
(8 Message Mode Indication (see page 50).
(5 Wide Screen Indication (see page 41).
(8 Date and Time Indication (see page 16).
(9 Backlight Indication (see page 33).
¿9 Manual Focus Indication (see page 34).
€) Light ON/OFF Indication (see page 22).
@ High Speed Shutter Indication (see page 35).
@ Fade Indication (see page 36).
@ Color Digital Fade Indication (see page 37).
®© Color Digital Filter Indication (see page 38).
20