Panasonic NV-GS70EG User manual

ORDERNO.VM0304018C8
Digital VideoCamera/Recorder
NV-GS70EG / NV-GS70EGM/ NV-GS70B / NV-GS70EN/ NV-
GS70A/ NV-GS70ENT
A-MECHANISM
SPECIFICATIONS
1

1. INTRODUCTION
1.1. INTRODUCTION
Note1:
1)Thisservice manual does notcontainthefollowing information, because oftheimpossibilityof
sevicing atcomponentlevel.
1. SchematicDiagram, Block Diagramand C.B.A. layoutofMain
C.B.A./ Sub C.B.A.
2. Parts List forindividual parts ofMainC.B.A./ Sub C.B.A.
3. ExplodedView and Parts List forindividual parts ofMechanism
Unit.
2)Thefollowing categoryis/arerecyclemodulepart. Please send it/them toCentral Repair
2

Center.
*MainC.B.A. (VEP03G39B)
*Sub C.B.A. (VEP23584B)
Whenapartreplacementisrequiredfor repairing eachMainC.B.A. and/ or Mechanism block,
replace theassemblyparts.
(MainC.B.A., Sub C.B.A. and/ or Mechanism Unit)
Thefollowing circuitsarecontainedinMainC.B.A.
1. MainConnection Circuit
2. DriveCircuit
3. Video1Circuit
4. Video2Circuit
5. Control Circuit
6. ExInputCircuit
7. LCD Circuit
8. Head/ Rec AmpCircuit
9. PowerCircuit
Thefollowing circuitsarecontainedinSub C.B.A.
1. Sub Connection Circuit
2. Process Circuit
3. DSCCircuit
4. LensDriveCircuit
5. SensorCircuit
1.2. ABOUTLEADFREE SOLDER(PbF)
Distinction ofPbF PCB: PCBs(manufactured)using leadfree solderwill have aPdF stampon the
PCB.
Caution:
-Pbfree solderhas ahighermelting pointthanstandardsolder,
Typicallythemelting pointis50-70°F(30-40°C)higher.
Please use ahigh temperaturesoldering iron. Incase ofsoldering
iron withtemperaturecontrol, please set itto700±20°F(370±10°C).
-Pbfree solderwill tend tosplashwhenheatedtoo high (about
1100°F/ 600°C).
Whensoldering or unsoldering, please completelyremove all ofthesolderon thepinsor solder
area, and besuretoheatthesoldering pointswiththePbfree solderuntil itmeltsenough.
3

2. CAUTIONFORACCORD (VJA0940 TYPE)
2.1. INFORMATIONFORYOUR SAFETY
IMPORTANT
Your attention isdrawntothefactthatrecording ofpre-recordedtapes or discs or other
publishedor broadcastmaterial may infringecopyrightlaws.
WARNING
To reduce therisk offireorshock hazard, do notexpose this
equipmenttorainormoisture.
CAUTION
To reduce therisk offireorshock hazardand annoying
interference, use therecommendedaccessories only.
FORYOUR SAFETY
DONOTREMOVE THE OUTERCOVER
Topreventelectricshock, do notremove thecover. Nouserserviceablepartsinside. Refer
servicing toqualifiedservice personnel.
2.2. CAUTIONFORACMAINSLEAD
For your safety, please readthefollowing textcarefully.
Thisappliance issuppliedwithamouldedthree-pinmainsplug for your safetyand convenience.
A5-amperefuse isfittedinthisplug.
Shouldthefuse needtobereplacedplease ensurethatthereplacementfuse has arating of5
amperes and itisapprovedbyASTAor BSItoBS1362
Check for theASRAmarkor theBSImarkon thebodyofthefuse.
Iftheplug containsaremovablefuse coveryou mustensurethatitisrefittedwhenthefuse is
replaced.
Ifyou lose thefuse cover, theplug mustnotbeuseduntil areplacementcoverisobtained.
Areplacementfuse covercanbepurchasedfrom your local PanasonicDealer.
Ifthefittedmouldedplug isunsuitablefor thesocketoutletinyour homethenthefuse shouldbe
removedand theplug cutoff and disposedofsafety.
Thereisadangerofsevereelectrical shock ifthecutoff plug isinsertedintoany13-ampere
socket.
Ifanewplug istobefittedplease observe thewiring codeas shownbelow.
Ifinanydoubt, please consultaqualifiedelectrician.
2.2.1. Important
Thewires inthismainsleadarecolouredinaccordance withthefollowing code:
Blue Neutral
Brown Live
4

Asthecoloursofthewires inthemainsleadofthisappliance may notcorrespond withthe
colouredmarkingsidentifying theterminalsinyour plug, proceedas follows:
ThewirewhichiscolouredBLUE mustbeconnectedtotheterminal intheplug whichismarked
withtheletterNor colouredBLACK.
ThewirewhichiscolouredBROWNmustbeconnectedtotheterminal intheplug whichis
markedwiththeletterLor colouredRED.
Underno circumstances shouldeitherofthese wires beconnectedtotheearthterminal ofthe
three pinplug, markedwiththeletterE or theEarthSymbol.
2.2.2. Beforeuse
remove theConnector Coveras follows.
2.2.3. Howtoreplace theFuse
1. RemovetheFuse Coverwithascrewdriver.
2. Replace thefuse and attachtheFuse cover.
3. SERVICE CAUTION
3.1. EEPROMDATAFORSPAREPARTSOFTHEMAINC.B.A.
WhentheMainC.B.A. isreplaced, thefixedand averagedatamustbechangedbyTatsujinkit
according totheMovieCamera’ssuffix.
Then, confirm and/or adjusttheVTRand Camerasection onebyone.
3.2. SERVICEEXTENSIONCABLES.
Thismodelsisrequiredthefollowing extension cables for all connections.
Note1:
5

Use thefollowing extension cables whenchecking or adjusting individual circuitboardsexcept
moduleParts.
(MainC.B.A. and Sub C.B.A.)
Howtouse extension cables.
Fig. T1-1
6

3.3. LOCATIONFORSPARECONNECTORSOFTHEMAINC.B.A.&
SUB C.B.A.
3.3.1. MAINC.B.A.
3.3.2. SUB C.B.A.
4. PREPARATIONFORELECTRICALADJUSTMENT
1. Unlock thelocking taband removetheEVRconnectoras shownin
Fig. E1.
7

2. Thenconnect thefollowing cables as shownin Fig. E2.
Fig. E1
Fig. E2
Fig. E3
5. SERVICE MODE
5.1. New ErrorCodeDisplay
Conventionally, theerror codehas beendisplayedautomaticallyon theEVFor LCD Monitor
whenundesirableconditionshave occurred. WiththeNewError CodeDisplay, theerror code
8

has notbeendisplayedautomaticallyas followsexceptsomeerror codesF31(DataTransmission
Error), U10(Dew)and U11(HeadClogging).
Note:
1. Theonlysomeerrorcodes F31, U10 and U11 has displayed
automaticallyon theEVForLCD monitoras usual.
2. ThePowerLEDalsohas beenflashedfor1min. whenundesirable
conditionshaveoccurred.(See below)
5.2. Viewing ErrorCode
Whendisplaying theError Codeon theEVFor LCD Monitor, pushtheFADE/STOP and REC
START/PAUSE buttonssimultaneouslyfor more3seconds.
Note:
Whenthecassette tapeisinserted, thisoperation will notbeworked.
9

6. HOWTO REPLACE THE LITHIUMBATTERY
(PROCEDURE)
1. RemovetheSideCase (L)C.B.A.. (RefertoDisassembly
Procedures.)
2. UnsoldertheLithiumBattery“ML920S/F9D”and thenreplace the
new one. (See Fig. B1.)
Fig. B1
Note:
Thelithium batteryisacritical component. (TypeNo.:ML920S/F9DManufacturedbyPanasonic.)
Itmustneverbesubjectedtoexcessive heator discharge.
Itmustthereforeonlybefittedinequipmentdesignedspecificallyfor itsuse.
Replacementbatteries mustbeofthesametypeand manufacture.
They mustbefittedinthesamemannerand location as theoriginal battery, withthecorrect
polaritycontactsobserved.
Donotattempttore-chargetheoldbatteryor re-use itfor anyotherpurpose.
Itshouldbedisposedofinwasteproductsdestinedfor burial ratherthanincineration.
10

7. ADJUSTMENTPROCEDURES
7.1. DISASSEMBLEFLOWCHART
Thisflowchartindicates thedisassemblystepsthecabinetparts, C.B.A. and Mecha. Unitinorder
toaccess tobeserviced. Whenreinstalling, perform thestepsinthereverse order.
11

Fig. F1
7.2. DISASSEMBLYPROCEDURES
Flow-Chartfor DisassemblyProcedure
No. Item / Part Fig. Removal
(Screw,Connector,Flex. &
Other)
1 Front
Case Unit Fig. D2 ItPushes 1and itRemoves GripBeltPiece.
Fig.
D3 1-Screw(A), 1-Screw(B), 1- Screw(C)
Fig.
D4 1-Screw(D)
1-Connector FP4801
FrontCase Unit
2 SideCase
(R) Unit/
LCD Unit
Fig.
D5 2-Screws(E)
Fig.
D6 2-Screws(F), 1-Screw(G)
Fig.
D7 1-Screw(H)
3-ConnectorsFP601,
FP3401, FP6503
SideCase (R) Unit/ LCD Unit
12

No. Item / Part Fig. Removal
(Screw,Connector,Flex. &
Other)
3RearCase
Unit Fig. D8 1-Screw(I), 1-Screw(J), 1- Screw(K), 1-Screw(L)
Fig.
D9 1-Screw(M)
Fig.
D10 2-ConnectorsFP1001, FP6502
RearCase Unit
4LensUnit Fig.
D11 1-Screw(N)
2-ConnectorsFP701, PS201
LensUnit
5 Sub C.B.A.
/ EVFUnit Fig. D12 2-ConnectorsFP3401, FP4002
Sub C.B.A.
3-Screws(O)
1-Connector FP603
EVFUnit
6Main
C.B.A. Fig. D13 1-Screw(P)
7-ConnectorsFP2201,
FP2202, FP2203, FP2204,
FP5001,
FP6501, FP6504
MainC.B.A.
7Jack
C.B.A. Fig. D14 2-Screws(Q)
1-Connector FP6201
Jack C.B.A.
8Mecha.
Unit Fig. D15 CassetteCoverOpen
3-Screws(R)
Mecha. Unit
9Front
C.B.A. Fig. D16 dischargedisposal
Itmoves Flashtothe
direction ofthearrow
2-Screws(S)
2-ConnectorsFP6501,
FP7002
FrontC.B.A.
13

No. Item / Part Fig. Removal
(Screw,Connector,Flex. &
Other)
10 Monitor
C.B.A. Fig. D17 2-Screws(T)
Fig.
D18 3-Screws(U)
RearCover
Fig.
D19 2-Screws(V)
SideCase (R) Unit
Fig.
D20 2-Screws(W)
8-Tabs
LCD Case (Upper)Unit
1-Connector FP903
LCD HingeUnit
Fig.
D21 LCD Case (Lower)
Fig.
D22 1-Connector FP901
2-SolderPortion
2-Tabs
Monitor C.B.A.
11 EVFC.B.A. Fig.
D23 1-Screw(X), 1-Screw(Y)
HotShoeUnit
Fig.
D24 2-Screws(Z)
2-SlidePies
SlideFrame
Fig.
D25 2-Screws(a)
EVFHingeUnit
Fig.
D26 6-Tabs
ViewADJ. Unit
EVFCase (Upper)/ EVF
Case (Lower)
Fig.
D27 3-Tabs
LensPolarization SeetHold/
LensPolarization Seet
Fig.
D28 3-Tabs
EVFC.B.A.
Fig. D1
14

Fig. D2
Fig. D3
15

Fig. D4
Fig. D5
Fig. D6
16

Fig. D7
Fig. D8
17

Fig. D9
Fig. D10
18

Fig. D11
Fig. D12
19

Fig. D13
Fig. D14
20