Panasonic NV-MD9000EN User manual

ORDERNO. VMD0207046C8
Digital Video Camera/Recorder
NV-MD9000EN
N-MECHANISM
SPECIFICATIONS
2002 Matsushita ElectricIndustrial Co., Ltd. All rights reserved.
1

Unauthorized copying and distribution isaviolation of law.
1. INTRODUCTION
1.1. INTRODUCTION
This service manual contains technical information whichwill allowservice personnel's to
understand and service this model.Please place orders using the parts list and not the drawing
reference numbers.
If the circuit is changedormodified, this information will be followedbysupplement service
manual tobe filedwithoriginal service manual.
Information forN-Mechanismshouldbe referdtothe anothermanual as below.
OrderNo. : VMD0105012C8
Information forMIC shouldbe referdtothe anothermanual as below.
OrderNo. : VMD0209047C8
Note 1:
These movie cameras use AC Adaptoris VSK0581-A.
The service manual forAC Adaptoris separate volume.
OrdernumberforAC Adaptor..........VSK0581-A : VMD0105013C8
Note 2:
1) This service manual does not containthe following information, because of the impossibility
of sevicing at component level.
1. SchematicDiagram, Block Diagram and C.B.A. layout of Main
C.B.A./ Mother C.B.A.
2. Parts List for individual parts of MainC.B.A./ Mother C.B.A.
3. Exploded View and Parts List for individual parts of Mechanism
Unit.
2) The following categoryare recycle module part. Please send themtoCentral RepairCenter.
*MainC.B.A. (VEP03F85F)
*MotherC.B.A. (VEP06F10A)
Whena part replacement is requiredforrepairing eachMainC.B.A. and/ orMechanismblock,
replace the assemblyparts.
(MainC.B.A., MotherC.B.A. and/ orMechanismUnit)
The following circuits are containedinMainC.B.A.
1. MainConnection Circuit
2

2. Drive Circuit
3. Video 1Circuit
4. Video 2Circuit
5. Control Circuit
6. LCD Circuit
7. Head/ Rec Amp Circuit
8. Power Circuit
9. Camera Circuit
10. Lens Drive Circuit
The following circuits are containedinMotherC.B.A.
1. Mother Connection Circuit
2. Ex Input Circuit
3. HPAmp Circuit
4. MF Ring Circuit
About leadfree solder(PbF)
Distinction of PbF PCB:
PCBs (manufactured) using leadfree solderwill have a PbF stampon the PCB.
Caution:
-Pb free solder has ahigher melting point than standard solder;
Typicallythe melting point is50-70°F (30-40°C)higher. Please use
ahigh temperature soldering iron. Incase of the soldering iron
with temperature control,please set itto 700±20°F (370±10°C).
-Pb free solder will tend to splash when heated too high (about
1100°F/ 600°C).
Whensoldering orunsoldering, please completelyremove all of the solderon the pins orsolder
area, and be sure toheat the soldering points withthe Pbfree solderuntil it melts enough.
2. CAUTION FOR AC CORD (VJA0940 TYPE)
2.1. INFORMATIONFORYOUR SAFETY
IMPORTANT
Yourattention is drawntothe fact that recording of pre-recordedtapes ordiscs orother
3

publishedorbroadcast material mayinfringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose this
equipment to rainor moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOTREMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. Nouserserviceable parts inside. Refer
servicing toqualifiedservice personnel.
2.2. CAUTIONFORAC MAINSLEAD
Foryoursafety, please readthe following text carefully.
This appliance is suppliedwitha mouldedthree-pinmains plug foryoursafetyand convenience.
A 5-ampere fuse is fittedinthis plug.
Shouldthe fuse needtobe replacedplease ensure that the replacement fuse has a rating of 5
amperes and it is approvedbyASTA orBSI toBS1362
Check forthe ASRA mark orthe BSI mark on the bodyof the fuse.
If the plug contains a removable fuse coveryou must ensure that it is refittedwhenthe fuse is
replaced.
If you lose the fuse cover, the plug must not be useduntil a replacement coveris obtained.
A replacement fuse covercanbe purchasedfromyourlocal Panasonic Dealer.
If the fittedmouldedplug is unsuitable forthe socket outlet inyourhome thenthe fuse should
be removedand the plug cut off and disposedof safety.
There is a dangerof severe electrical shock if the cut off plug is insertedintoany13-ampere
socket.
If a newplug is tobe fittedplease observe the wiring code as shownbelow.
If inanydoubt, please consult a qualifiedelectrician.
2.2.1. Important
The wires inthis mains leadare colouredinaccordance withthe following code:
Blue Neutral
Brown Live
As the colours of the wires inthe mains leadof this appliance maynot correspond withthe
colouredmarkings identifying the terminals inyourplug, proceedas follows:
The wire whichis colouredBLUE must be connectedtothe terminal inthe plug whichis marked
withthe letterN orcolouredBLACK.
The wire whichis colouredBROWN must be connectedtothe terminal inthe plug whichis
4

markedwiththe letterLorcolouredRED.
Underno circumstances shouldeitherof these wires be connectedtothe earthterminal of the
three pinplug, markedwiththe letterE orthe EarthSymbol.
2.2.2. Beforeuse
remove the ConnectorCoveras follows.
2.2.3. Howtoreplace the Fuse
1. Remove the Fuse Cover with ascrewdriver.
2. Replace the fuse and attach the Fuse cover.
3. SERVICE CAUTION
3.1. EEPROMDATAFORSPAREPARTS OFTHEMAINC.B.A.
Whenthe MainC.B.A. is replaced, the fixedand average data must be changedbyTatsujinkit
according tothe Movie Camera’s suffix.
Then, confirm and/oradjust the VTR and Camera section one byone.
3.2. SERVICEEXTENSIONCABLES
This models is requiredthe following extension cables forall connections.
Note 1:
Use the following extension cables whenchecking oradjusting individual circuit boards except
module Parts.
(MainC.B.A. and MotherC.B.A.)
5

Howtouse extension cables.
Fig. T1-1
3.3. LOCATIONFORSPARECONNECTORSOFTHEMAINC.B.A. &
MOTHERC.B.A.
3.3.1. MAIN C.B.A.
3.3.2. MOTHER C.B.A.
4. PREPARATION FOR ELECTRICAL ADJUSTMENT
1. Unlock the locking tab and remove the EVRconnector as shown
in Fig. E1 .
2. Then connect the following cables as shownin Fig. E2 .
Fig. E1
6

Fig. E2
Fig. E3
5. SERVICE MODE
5.1. New Error Code Display
Conventionally, the errorcode has beendisplayedautomaticallyon the EVForLCD Monitor
whenundesirable conditions have occurred. Withthe NewErrorCode Display, the errorcode
has not beendisplayedautomaticallyas follows except some errorcodesF31(Data
Transmission Error), U10(Dew) and U11(HeadClogging).
7

Note:
1. The onlysome error codes F31, U10 and U11 has displayed
automaticallyon the EVF or LCD monitor as usual.
2. The Power LEDalso has been flashed for 1min. when undesirable
condetions have occurred.(See below)
5.2. Viewing Error Code
Whendisplaying the ErrorCode on the EVForLCD Monitor, pushthe FADE/STOP and REC
START/PAUSE buttons simultaneouslyformore 3 seconds.
Note:
When the cassette tape isinserted, thisoperation will not be
worked.
8

6. HOW TO REPLACE THE LITHIUM BATTERY
(PROCEDURE)
1. Remove the Mother C.B.A.. (Refer to DisassemblyProcedures.)
2. Unsolder the Lithium Battery“ML920S” and then replace the new
one. (See Fig. B1 .)
Fig. B1
Note:
The lithiumbatteryis a critical component. (Type No.: ML920S ManufacturedbyPanasonic.)
It must neverbe subjectedtoexcessive heat ordischarge.
It must therefore onlybe fittedinequipment designedspecificallyforits use.
Replacement batteries must be of the same type and manufacture.
Theymust be fittedinthe same mannerand location as the original battery, withthe correct
polaritycontacts observed.
Donot attempt tore-charge the oldbatteryorre-use it foranyotherpurpose.
It shouldbe disposedof inwaste products destinedforburial ratherthanincineration.
9

7. OPERATING GUIDE
8. ADJUSTMENT PROCEDURES
8.1. DISASSEMBLE FLOWCHART
This flowchart indicates the disassemblysteps the cabinet parts, C.B.A. and Mecha. Unit in
ordertoaccess tobe serviced. Whenreinstalling, perform the steps inthe reverse order.
Fig. F1
10