Panasonic KX-TCD951RUB User manual

•|1•|
KX-TCD951RUB
Simplified
Digital Cordless Phone
Telephone Equipment
KX-TCD951RUB
(for Russia)
©2000 Kyushu Matsushita Electric Co., Ltd.
All rights reserved. Unauthorized copying and distribution is a violation of law.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians.
Any attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious injury
or death.
Please use this manual together with the original Service Manual for model KX-TCD951GB/KX-TCD955GC order
No.KM49910781C2. This Service Manual indicates the main differences between: Original KX-TCD951GB /KX-TCD955GC
and KX-TCD951RUB.
ORDER NO. KM40005622A1
Black Version
(Handset) (Base Unit)
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
0
WXYZ
9
INT'
OK
OK
C
PWR
RCL
PROG
RDL

•|3•|
KX-TCD951RUB
•¡LOCATION OF CONTROLS (Change from original page 3)
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
0
WXYZ
9
R
INT’
OK
C
Tone Button
Display
Talk Button
Cancel Button
Program Button
Recall Button
Charge Contacts
Intercom Button
Redial/Pause
Button
OK Button
Power Button
INT
OK
R
Navigator Key
C
The underlined parts has been added to the original.
•¡Battery Information (Change from original page 7)
•¡•¡
•¡•¡
•¡TO REDIAL AFTER CONFIRMING THE NUMBERS IN REDIAL MEMORY (Changw from original page 11)
The underlined parts has been added to the original.
3Press .
• The number is dialed automatically.
• If your line has rotary or pluse service, any access numbers entered after pressing will not be included when
redialing.
* Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.
When you replace the batteries, you must program the battery type selection.
(Model KX-TCD951RUB)

•|4•|
KX-TCD951RUB
3. Send batch file “SET FREQ nn” to set the clock frequency. The default value of nn is 80. Increase the value to
increase the frequency. The clock frequency must be 10,368.000 kHz ± 0.04 kHz.
•¡CHECK PROCEDURE (Change from original page 41)
TEST EQUIPMENT REQUIRED AND EQUIPMENT SETUP
Connect a 3.9V supply to the board J5 (+), J8 (–).
INITIAL POWER + BBIC TESTS
4. Check the 3.0V supply voltage (TP10). It must be 2.85 +/– 0.3V.
5. Connect RFCLK (TP56) to CH.1 on the scope. Send batch file RFCLK1.
6. Check if the clock waveform is 10,368.000 kHz,+/– 40Hz.
7. Send batch file “SELF TEST”. The first 4digits are FLASH ROM checksum, the next 2 digits are RAM test,
and must be 00
SET CLOCK FREQUENCY
1. Send batch file “RFCLK1”.
(Model KX-TCD951RUB)
•¡CABINET AND ELECTRICAL PARTS LOCATION (HANDSET) [Change from original page 54]
Addition
LCD121
121

•|7•|
12345678 9 10 11 12
G
F
E
D
C
B
A
H
KX-TCD951RUB KX-TCD951RUB
SCHEMATIC DIAGRAM (Base Unit) [Change from original page 17]

KX-TCD951RUB
•|8•|
12345678 9 10 11 12
G
F
E
D
C
B
A
H
KX-TCD951RUB
SCHEMATIC DIAGRAM (Handset) [Change from original page 18]