Panasonic KX-TG1805NZ User manual

This unit is Caller ID compatible. To display the caller’s phone
number, you must subscribe to Caller ID service.
Charge the batteries for about 7 hours before initial use.
Please read these operating instructions before using the unit and save them for
future reference.
Operating Instructions
Model No. KX-TG1805NZ
Digital Cordless Phone

Introduction
2
Introduction
Thank you for purchasing a new Panasonic digital cordless phone.
For your future reference
Attach or keep original receipt to assist with any repair under warranty.
Note:
LIn the event of problems, you should contact your equipment supplier in the first instance.
Serial No. (found on the bottom of the base unit)
Date of purchase
Name and address of dealer

Table of Contents
3
Preparation
Accessory information . . . . . . . . . . . . . . .4
Important information . . . . . . . . . . . . . . . .5
Controls and displays . . . . . . . . . . . . . . . .6
Connections . . . . . . . . . . . . . . . . . . . . . . .7
Battery installation . . . . . . . . . . . . . . . . . .8
Battery charge . . . . . . . . . . . . . . . . . . . . .8
Battery replacement . . . . . . . . . . . . . . . . .9
Turning the power on/off. . . . . . . . . . . . . .9
Setting the date and time . . . . . . . . . . . . .9
Making/Answering Calls
Making calls . . . . . . . . . . . . . . . . . . . . . .11
Answering calls . . . . . . . . . . . . . . . . . . .12
Phonebook
Using the phonebook . . . . . . . . . . . . . . .14
Handset Settings
Guide to handset settings. . . . . . . . . . . .16
Ringer setup . . . . . . . . . . . . . . . . . . . . . .17
Night mode . . . . . . . . . . . . . . . . . . . . . . .17
Display setup . . . . . . . . . . . . . . . . . . . . .18
Call options. . . . . . . . . . . . . . . . . . . . . . .18
Other options . . . . . . . . . . . . . . . . . . . . .19
Base Unit Settings
Guide to base unit settings. . . . . . . . . . .21
Ringer setup . . . . . . . . . . . . . . . . . . . . . .22
Call options. . . . . . . . . . . . . . . . . . . . . . .23
Other options . . . . . . . . . . . . . . . . . . . . .25
Caller ID Service
Using Caller ID service. . . . . . . . . . . . . .26
Caller list. . . . . . . . . . . . . . . . . . . . . . . . .26
Call minder . . . . . . . . . . . . . . . . . . . . . . .27
Multi-unit Operation
Operating additional units. . . . . . . . . . . .28
Registering a handset to a base unit . . .28
Intercom between handsets . . . . . . . . . .30
Transferring calls between handsets . . .30
Useful Information
Wall mounting . . . . . . . . . . . . . . . . . . . .31
Available character entries. . . . . . . . . . .32
Troubleshooting . . . . . . . . . . . . . . . . . . .34
Specifications . . . . . . . . . . . . . . . . . . . . . 37
Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Preparation
4
Accessory information
Included accessories
Additional/replacement accessories
General Warning:
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has
accepted that the item complies with minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in all respects with
another item of Telepermitted equipment of a different make or model, nor does it imply that
any product is compatible with all of Telecom’s network services.
Important Notice:
Under power failure conditions, this telephone may not operate. Please ensure that a
separate telephone, not dependent on local power, is available for emergency use.
AC adaptor
PQLV19AL
Telephone line cord Rechargeable batteries
(AAA size)
HHR-4EPT
Handset cover Operating instructions
Model No. Description
HHR-4EPT 2 rechargeable nickel metal hydride (Ni-MH) batteries
KX-TGA120AZ Additional Digital Cordless Handset
KX-A272 DECT repeater

Preparation
5
Important information
General
LUse only the AC adaptor included with this
product, noted on page 4.
LDo not connect the AC adaptor to any AC
outlet other than a standard 220–240 V
AC outlet.
LThis product is unable to make calls when:
– The portable handset battery(ies) need
recharging or have failed.
– There is a power failure.
– The key lock feature is turned on.
– The call bar feature is turned on (only
phone numbers stored in the unit as
emergency numbers can be called).
LDo not open the base unit or handset
other than to replace the battery(ies).
LThis product should not be used near
emergency/intensive care medical
equipment and should not be used by
people with pacemakers.
LCare should be taken that objects do not
fall onto, and liquids are not spilled into,
the unit. Do not subject this product to
excessive smoke, dust, mechanical
vibration or shock.
Environment
LDo not use this product near water.
LThis product should be kept away from
heat sources such as radiators, cookers,
etc. It should also not be placed in rooms
where the temperature is less than 5 °C or
greater than 40 °C.
LThe AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the unit and is
easily accessible.
Warning:
LTo prevent the risk of electrical shock, do
not expose this product to rain or any
other type of moisture.
LUnplug this unit from power outlets if it
emits smoke, an abnormal smell or makes
unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped and contact an
authorised service centre.
Location
LFor maximum distance and noise-free
operation, place your base unit:
– Away from electrical appliances such as
TVs, radios, personal computers or
other phones.
– In a convenient, high and central
location.
Battery caution
LWe recommend using the battery(ies)
noted on page 4. Use only rechargeable
battery(ies).
LDo not mix old and new batteries.
LDo not dispose of the battery(ies) in a fire,
as they may explode. Check local waste
management codes for special disposal
instructions.
LDo not open or mutilate the battery(ies).
Released electrolyte from the battery(ies)
is corrosive and may cause burns or injury
to the eyes or skin. The electrolyte may be
toxic if swallowed.
LExercise care when handling the
battery(ies). Do not allow conductive
materials such as rings, bracelets or keys
to touch the battery(ies), otherwise a short
circuit may cause the battery(ies) and/or
the conductive material to overheat and
cause burns.
LCharge the battery(ies) in accordance
with the information provided in these
operating instructions.
LOnly use the included base unit (or
charger) to charge the battery(ies). Do not
tamper with the base unit (or charger).
Failure to follow these instructions may
cause the battery(ies) to swell or explode.

Preparation
6
Controls and displays
Controls
Handset
ACharge contact
B{k} (Phonebook)
C{C} (Talk)
DNavigator key
L {e}{v}: To search for the desired
item in menus.
L{>}: To select the desired item or
move the cursor to the right.
L{<}: To return to the previous screen
or move the cursor to the left.
E{R} (Redial/Pause)
F{R}(Recall)
GReceiver
HDisplay
I{j/OK}(Menu/OK)
J{ih} (Off/Power)
K{C/T}(Clear/Mute)
L{INT}(Intercom)
MMicrophone
Note:
LUp to 3 menu items can be displayed at a
time. To select a menu item not shown on
the current page, scroll up or down by
pressing the navigator key, {e} or {v},
respectively.
Base unit
A{x} (Page)
BCharge contact
C
h
T
i
N
a
L
M
C
D
E
F
BJ
G
K
A
H
I
A
B

Preparation
7
Displays
Display icons
Various icons appear on the handset display
to indicate the current status of the unit.
Connections
When the AC adaptor is connected, a short
beep will be heard. If it is not heard, check
the connections.
Important:
LUse only the AC adaptor and telephone
line cord supplied with this unit.
Note:
LAfter connection, you must charge the
batteries to make or answer calls (page
8).
LNever install telephone wiring during a
lightning storm.
LThe AC adaptor must remain connected
at all times. (It is normal for the adaptor to
feel warm during use.)
LThe AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight
of the adaptor may cause it to become
disconnected.
Display
icon
Meaning
wWithin range of a base unit
LWhen flashing: Handset
is searching for base unit.
(out of range of base unit,
handset is not registered
to base unit, no power on
base unit)
LHandset is accessing base
unit. (intercom, paging,
changing base unit settings,
etc.)
kHandset is on an outside
call.
oCall bar is on. (page 19)
5Battery strength
[VE] Voice enhancer is set to
high or low tone. (page 12)
[N] Night mode is on. (page 18)
[X] Key lock is on. (page 12)
[2] Handset number: The left
icon shows handset 2
example. (page 18)
0New call minder message
received (call minder users
only; page 27)
Line is being used by
another handset.
(220–240 V, 50 Hz)
To telephone
network
Hooks

Preparation
8
Battery installation
1Insert the batteries negative (T)
terminal first.
2Close the handset cover.
Note:
LUse only rechargeable batteries (page 4).
Battery charge
Place the handset on the base unit for
about 7 hours before initial use.
When charging, the battery icon is shown as
follows.
When the batteries are fully charged, 5
remains on the display.
Note:
LIt is normal for the handset to feel warm
during charging.
LIt takes 7 hours to fully charge the
batteries, however, you can use the
handset before the batteries are fully
charged.
LClean the charge contacts (page 6) of the
handset and base unit with a soft, dry
cloth once a month, otherwise the
batteries may not charge properly. Clean
more often if the unit is exposed to grease,
dust or high humidity.
Battery strength
Note:
LWhen 7flashes, recharge the handset
batteries. 7will continue to flash until
the batteries have been charged for at
least 15 minutes.
Battery icon Battery strength
5High
6Medium
7Low
When flashing: Needs
to be charged.

Preparation
9
LIf the handset is turned off, it will be turned
on automatically when it is placed on the
base unit.
Battery life
After your Panasonic batteries are fully
charged, you can expect the following
performance:
Ni-MH batteries (700 mAh)
Note:
LActual battery performance depends on a
combination of how often the handset is in
use (talking) and how often it is not in use
(standby).
LBattery operating time may be shortened
over time depending on usage conditions
and ambient temperature.
Battery replacement
If 7flashes even after the handset
batteries have been charged for 7 hours, the
batteries must be replaced.
Important:
LWe recommend the use of Panasonic
rechargeable batteries noted on page 4. If
you install non-rechargeable batteries and
start charging, the batteries may leak
electrolyte.
LDo not mix old and new batteries.
1Press the notch on the handset cover
firmly and slide it in the direction of the
arrow.
2Remove the old batteries positive (S)
terminal first and install the new ones.
See page 8 for battery installation.
Turning the power on/off
Power on
Press {ih} for about 1 second.
LThe display will change to the standby
mode.
Power off
Press {ih} for about 2 seconds.
LThe display will go blank.
Setting the date and time
Important:
LConfirm that the AC adaptor is connected.
LEnsure that wis not flashing.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Set Date & Time”, then press
{>}.
4Enter the current day, month and year by
selecting 2 digits for each.
Example: 17 May, 2005
Press {1}{7}{0}{5}{0}{5}.
Operation Operating time
While in use (talking) 20 hours max.
While not in use
(standby)
170 hours max.

Preparation
10
5Enter the current hour and minute by
selecting 2 digits for each.
LYou can select “AM”,“PM”or 24-hour
time entry by pressing {*} repeatedly.
Example: 3:30 PM
Press {0}{3}{3}{0}, then press {*}
repeatedly until “03:30 PM”is
displayed.
6Press {j/OK}.
7Press {ih}.
Note:
LTo correct a digit, press {<} or {>} to
move the cursor, then make the
correction.
LThe date and time may be incorrect after a
power failure. In this case, set the date
and time again.

Making/Answering Calls
11
Making calls
1Lift the handset and dial the phone
number.
LTo correct a digit, press {C/T}, then
enter the correct number.
2Press {C}.
3When finished talking, press {ih} or
place the handset on the base unit.
To adjust the receiver volume
Press {e} or {v} while talking. 4 volume
levels are available for the receiver.
Redial feature
Previously dialled phone numbers (each 24
digits max.) can be redialled.
To redial the last number dialled
Press {R}, then press {C}.
Note:
LYou can also press {C} before pressing
{R}.
To make a call using the redial list
The last 10 phone numbers dialled are
stored in the redial list.
1Press {R}.
LThe last number dialled will be
displayed.
2Press {e} or {v} repeatedly to select
the desired number.
LTo exit the list, press {ih}.
3Press {C}.
To edit a number in the redial list before
calling it
1Press {R}.
2Press {e} or {v} repeatedly to select
the desired number, then press
{j/OK}.
3Select “Edit and Call”, then press
{>}.
4Press {<} or {>} to move the cursor,
then edit the number.
LPlace the cursor on the number you
wish to erase, then press {C/T}.
LPlace the cursor to the right of where
you want to insert a number, then
press the appropriate dial key.
5Press {C}.
To erase numbers in the redial list
1Press {R}.
2Press {e} or {v} repeatedly to select
the desired number, then press
{j/OK}.
3Select “Erase”, then press {>}.
LIf you want to erase all numbers in the
list, select “Erase All”, then press
{>}.
4Select “Yes”, then press {>}.
5Press {ih}.
To store a number from the redial list into
the phonebook
1Press {R}.
2Press {e} or {v} repeatedly to select
the desired number, then press
{j/OK}.
3Select “Add Phonebook”, then press
{>}.
4Enter a name (16 characters max.; see
page 32 for character entry), then press
{j/OK}.
5Edit the phone number if necessary,
then press {j/OK}.
6Select “Save”, then press {>}.
7Press {ih}.

Making/Answering Calls
12
Other features
Voice enhancer
You can change the tone quality of the
receiver while you are on a call. 3 settings
are available.
1Press {j/OK}during a call.
2Select the desired setting, then press
{>}.
Note:
LIf you select “High Tone”or “Low
Tone”,“[VE]”is displayed.
Mute
You can mute your voice during a
conversation. While mute is turned on, you
will be able to hear the other party, but the
other party will not be able to hear you.
1To mute your voice, press {C/T}.
2To return to the conversation, press
{C/T}again.
Key lock
The handset can be locked so that no calls
or settings can be made. Incoming calls can
be answered, but all other functions are
disabled while key lock is on.
To turn key lock on, press {j/OK}for about
2 seconds.
L“[X]”is displayed.
LTo turn key lock off, press {j/OK}for
about 2 seconds.
Note:
LCalls to emergency numbers (page 23)
cannot be made until key lock is turned
off.
LKey lock is turned off when the handset is
turned off.
R button (to use the recall feature)
{R}is used to access optional telephone
services. Contact your service provider for
details.
Note:
LIf your unit is connected to a PBX (private
branch exchange), pressing {R}can allow
you to access certain features of your host
PBX such as transferring an extension
call. Consult your PBX dealer for details.
LYou can change the recall time (page 23).
Call waiting
Call waiting is a service offered by your
service provider whereby a second caller
can be answered while online with the first
caller. To answer the second caller, press
{R}. To return to the first caller, press {R}
again. Please consult your service provider
for details of this service.
Pause button (for PBX/long distance
service users)
A pause is sometimes required when
making calls using a PBX or long distance
service.
Example: If you have to dial {0}before
dialling outside numbers manually, you will
probably pause after dialling {0}until you
hear a dial tone.
1Press {0}.
2Press {R}.
3Dial the phone number, then press
{C}.
Note:
LPressing {R} 1 time creates 1 pause.
Press {R} repeatedly to create longer
pauses. To change pause length, see
page 23.
Answering calls
1Lift the handset and press {C} when
the unit rings.
LYou can also answer a call by pressing
any dial key from {0}to {9},{*},{#},
or {INT}.(Any key answer feature)

Making/Answering Calls
13
2When finished talking, press {ih} or
place the handset on the base unit.
Auto talk feature
You can answer calls simply by lifting the
handset off the base unit. You do not need to
press {C}. To turn this feature on, see
page 19.
To adjust the ringer volume when an
outside call comes in
Press {e} or {v} when an outside call
comes in.
Note:
LThe ringer volume cannot be adjusted if
the handset is on the base unit.
Other features
Handset locator
Using this feature, you can locate the
handset if it has been misplaced.
1Press {x} on the base unit.
LThe base unit will page the handset
for about 1 minute.
2To stop paging, press {x} on the base
unit or press {ih} on the handset.

Phonebook
14
Using the phonebook
The phonebook allows you to make calls
without having to dial manually. You can add
20 names and phone numbers to the
phonebook and search for phonebook
entries by name.
Adding entries to the phonebook
1Press {k}, then press {j/OK}.
2Select “New Entry”, then press {>}.
3Enter the party’s name (16 characters
max.; see page 32 for character entry),
then press {j/OK}.
4Enter the party’s phone number (24
digits max.), then press {j/OK}.
5Select “Save”, then press {>}.
6Press {ih}.
Note:
LIf there is no space to store new entries,
“Memory Full”will be displayed. Erase
unnecessary entries (page 14).
To edit/correct a mistake
Press {<} or {>} to place the cursor on the
number or character you wish to erase, then
press {C/T}. Place the cursor to the right of
where you want to insert a number or
character, then press the appropriate dial
key.
Note:
LPress and hold {C/T}to erase all
numbers or characters.
Finding and calling a phonebook
entry
Phonebook entries can be searched for by
scrolling through all phonebook entries.
Once you have found the desired entry,
press {C} to dial the phone number.
Scrolling through all entries
1Press {k}.
2Press {e} or {v} repeatedly to display
the desired entry.
Editing entries in the phonebook
Phonebook entries can be edited after you
have saved them. You can change the name
and phone number.
Changing a name and phone number
1Find the desired entry (page 14), then
press {j/OK}.
2Select “Edit”, then press {>}.
3Edit the name if necessary (16
characters max.; see page 32 for
character entry), then press {j/OK}.
4Edit the phone number if necessary (24
digits max.), then press {j/OK}.
5Select “Save”, then press {>}.
6Press {ih}.
Erasing entries from the
phonebook
Erasing an entry
1Find the desired entry (page 14), then
press {j/OK}.
2Select “Erase”, then press {>}.
3Select “Yes”, then press {>}.
4Press {ih}.
Erasing all entries
1Press {k}, then press {j/OK}.
2Select “Erase All”, then press {>}.
3Select “Yes”, then press {>}.
4Select “Yes”again, then press {>}.
5Press {ih}.

Phonebook
15
Chain dial
This feature allows you to dial phone
numbers in the phonebook while you are on
a call. This feature can be used, for
example, to dial a calling card access
number or bank account PIN that you have
stored in the phonebook, without having to
dial manually.
1While on a call, press {k}.
2Press {e} or {v} repeatedly to select
the desired entry.
3Press {>} to dial the number.

Handset Settings
16
Guide to handset settings
For your reference, a chart of all items which can be customised for the handset is printed
below.
LWhen customising the handset, the current item or setting is indicated by >.
Note:
LUp to 3 menu items can be displayed at a time. To select a menu item not shown on the
current page, scroll up or down by pressing the navigator key, {e} or {v}, respectively.
Handset settings
menu
Sub-menu Sub-menu 2 Default setting Page
Set Date & Time — — page 9
Ringer Setup Ringer Volume Maximum page 17
Ext. Ringtone Ringtone 1 page 17
Int. Ringtone Ringtone 1 page 17
Night Mode Start/End 23:00/06:00 page 17
On/Off Off page 17
Ring Delay 60 sec. page 18
Display Setup Standby Display Off page 18
Contrast Level 3 page 18
Call Options Call Bar Off page 18
Auto Talk Off page 19
Registration Register H.set — page 28
Other Options Handset PIN 0000 page 19
Keytones On page 19
Reset Handset —page19

Handset Settings
17
Ringer setup
Ringer volume
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Ringer Setup”, then press
{>}.
4Select “Ringer Volume”, then press
{>}.
5Press {e} or {v} repeatedly to select
the desired volume.
6Press {>}.
7Press {ih}.
Note:
LThe handset will ring for intercom calls
and when paged even if the ringer is
turned off.
Changing ringtones
You can change the ringtone used by the
handset.
“Ext. Ringtone”: Selects the ringtone for
outside calls.
“Int. Ringtone”: Selects the ringtone for
intercom calls.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Ringer Setup”, then press
{>}.
4Select the desired item, then press {>}.
5Select the desired ringtone, then press
{>}.
6Press {ih}.
Night mode
Night mode allows you to select a block of
time during which the handset will not ring
for outside calls. This feature is useful for
times when you do not want to be disturbed,
for example, while sleeping. Night mode can
be set independently for the handset and the
base unit (page 22).
Set the date and time beforehand (page 9).
Setting the start and end time for night
mode
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Ringer Setup”, then press
{>}.
4Select “Night Mode”, then press {>}.
5Select “Start/End”, then press {>}.
6Enter the desired hour and minute you
wish to start this feature by selecting 2
digits for each.
LIf you use 12-hour time entry, select
“AM”or “PM”by pressing {*}
repeatedly before entering the time.
7Enter the desired hour and minute you
wish to end this feature by selecting 2
digits for each.
LIf you use 12-hour time entry, select
“AM”or “PM”by pressing {*}
repeatedly before entering the time.
8Press {j/OK}.
9Press {ih}.
Turning night mode on/off
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Ringer Setup”, then press
{>}.

Handset Settings
18
4Select “Night Mode”, then press {>}.
5Select “On/Off”, then press {>}.
6Select “On”or “Off”, then press {>}.
7Press {ih}.
Note:
LWhen the night mode is turned on, “[N]”
is displayed.
Setting the ring delay for night mode
This setting allows the handset to ring during
night mode if the caller waits long enough.
After the selected amount of time passes,
the handset will ring, useful when someone
urgently needs to speak with you. If you
select “No Ringing”, the handset will not
ring during night mode.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Ringer Setup”, then press
{>}.
4Select “Night Mode”, then press {>}.
5Select “Ring Delay”, then press {>}.
6Select the desired setting, then press
{>}.
7Press {ih}.
Display setup
Selecting the standby mode
display
“Handset Number”: The current handset
number is displayed.
“Off”: Only the current date and time are
displayed.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Display Setup”, then press
{>}.
4Select “Standby Display”, then
press {>}.
5Select the desired setting, then press
{>}.
6Press {ih}.
Note:
LIf “Handset Number”is selected and the
current handset number is 2, “[2]”is
displayed.
Changing the display contrast
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Display Setup”, then press
{>}.
4Select “Contrast”, then press {>}.
5Press {e} or {v} repeatedly to select
the desired contrast, then press {>}.
6Press {ih}.
Call options
Turning call bar on/off
This feature prohibits making outside calls.
When call bar is turned on, only intercom
calls and calls to emergency numbers (page
23) can be made.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Call Options”, then press
{>}.
4Select “Call Bar”, then press {>}.
5Enter “0000”(default handset PIN).
LIf you changed the PIN, enter it (page
19).
6Select “On”or “Off”, then press {>}.

Handset Settings
19
7Press {ih}.
Note:
LWhen call bar is turned on, ois
displayed.
Turning auto talk on/off
When this feature is turned on, you can
answer calls simply by lifting the handset off
the base unit. You do not need to press
{C}.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Call Options”, then press
{>}.
4Select “Auto Talk”, then press {>}.
5Select “On”or “Off”, then press {>}.
6Press {ih}.
Other options
Changing the handset PIN
(Personal Identification Number)
For security, the handset PIN must be
entered when changing certain settings. The
default PIN is “0000”.
Important:
LIf you change the PIN, please make note
of your new PIN. The unit will not reveal
the PIN to you. If you forget your PIN,
consult your nearest Panasonic service
centre.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Other Options”, then press
{>}.
4Select “Handset PIN”, then press
{>}.
5Enter the current 4-digit handset PIN.
6Enter the new 4-digit handset PIN, then
press {j/OK}.
7Press {ih}.
Turning keytones on/off
Keytones are tones heard when keys are
pressed. Includes confirmation tones and
error tones.
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Other Options”, then press
{>}.
4Select “Keytones”, then press {>}.
5Select “On”or “Off”, then press {>}.
6Press {ih}.
Note:
LIf keytones are turned off, error tones will
not sound when you enter the wrong PIN
or when memory is full.
Resetting the handset to its
default settings
1Press {j/OK}.
2Select “Handset Setup”, then press
{>}.
3Select “Other Options”, then press
{>}.
4Select “Reset Handset”, then press
{>}.
5Enter “0000”(default handset PIN).
LIf you changed the PIN, enter it (page
19).
6Select “Yes”, then press {>}.
7Press {ih}.
Note:
LThe following items will be deleted or reset
to their default settings:

Handset Settings
20
– Settings listed on page 16
– Redial list
– Voice enhancer
LThe following items will be retained:
– Phonebook entries
– Date and time