Panasonic KX-TG7331FX User manual

PNQW1226ZA DC0708DN0 FX-3/4
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
(220-240 V AC, 50 Hz)
To telephone
line
DSL/ADSL filter
(For DSL/ADSL service
users)
Hook
Plug
Press plug firmly.
“Click”
Use only the supplied Panasonic
AC adaptor PQLV207CE.
Use only the supplied
telephone line cord.
Base unit
Model No. KX-TG7331FX
KX-TG7341FX
Quick Guide
To use this unit in your country, first change the unit’s region setting to match your
country. Change the unit’s display language as needed.
Refer to “Changing the unit’s region setting” in the operating instructions.
TG7331_7341FX(e)_QG.fm Page 1 Friday, July 11, 2008 9:47 AM

– 2 –
Battery installation/Battery charge
Charge for about 7 hours.
Note:
LUSE ONLY Ni-MH batteries AAA (R03) size.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Operating tips
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select items
shown on the display by pressing {^}, {V},
{<}, or {>}.
To adjust the receiver or speaker volume,
press {^} to increase the volume, or press {V}
to decrease the volume repeatedly while
talking.
Soft keys
The handset features 3 soft keys. By pressing
a soft key, you can select the feature shown
directly above it on the display.
Rechargeable
Ni-MH ONLY
* Model shown is KX-TG7331.
“Charging”is
displayed.
{V}
{^}
Volume up
Volume down
{<}{>}
TG7331_7341FX(e)_QG.fm Page 2 Friday, July 11, 2008 9:47 AM

– 3 –
Display language (Handset) (default: English)
16 display languages are available.
You can select “Deutsch”, “English”, “Magyar”, “Polski”, “SlovenČina”,
“ČeŠtina”, “Hrvatski”, “Slovenscina”, “Eesti”, “LIETUVIŠKAI”,
“LatvieŠu”, “Românã”, “БЪЛГАРСКИ”, “Srpski”, “МАКЕДОНСКИ”, or “Shqip”.
1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Display Setup”iM
4{V}/{^}: “Select Language”iM
5{V}/{^}: Select your desired language. iMi{ih}
Note:
LIf you select a language you cannot read: {ih} iKi{^} 2 times iM
i{V} 2 times iM2 times i{V}/{^}: Select your desired language. i
Mi{ih}
Dialling mode (Handset) (default: Tone)
1K(middle soft key)
2{V}/{^}: “Base Unit Setup”iM
3{V}/{^}: “Dial Mode”iM
4{V}/{^}: Select the desired setting. iMi{ih}
Date and time (Handset)
1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Time Settings”iM
4{V}/{^}: “Set Date & Time”iM
5Enter the current date, month, and year.
6Enter the current hour and minute.
7Mi{ih}
TG7331_7341FX(e)_QG.fm Page 3 Friday, July 11, 2008 9:47 AM

– 4 –
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
To hang up {ih}
To adjust the receiver/
speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial
list
j(right soft key) i{V}/{^}: Select the desired
phone number. i{C}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
Handset ringer volume 1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Ringer Setup”iM
4{V}/{^}: “Ringer Volume”iM
5{V}/{^}: Select the desired volume. iMi
{ih}
Making/Answering calls (Base unit)
Making calls {s} iDial the phone number.
Answering calls {s}
To hang up {s}
To adjust the speaker
volume
Press {^} or {V} repeatedly while talking.
Redialling the last number
dialled
{s} i{R}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
To adjust the base unit ringer
volume
Press {^} or {V} repeatedly to select the desired
volume.
LTo turn the ringer off, press and hold {V} until the
unit beeps.
TG7331_7341FX(e)_QG.fm Page 4 Friday, July 11, 2008 9:47 AM

– 5 –
Phonebook (Handset)
Adding entries 1n(left soft key) iK
2{V}/{^}: “New Entry”iM
3Enter the party’s name (16 characters max.). i
M
LYou can change the character entry mode by
pressing /.
4Enter the party’s phone number (24 digits max.).
iM2 times i{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1n(left soft key)
2{V}/{^}: Select the desired entry.
LYou can scroll through the phonebook entry by
pressing and holding {V} or {^}.
3{C}
Answering system (Base unit): KX-TG7341
Answering on/off Press {s}to turn on/off the answering system.
Listening to messages {6}
Frequently asked questions
Question Cause/solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit’s AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
LThe handset is not registered to the base unit.
Register it (page 8).
Why can I not make calls? LThe dialling mode may be set incorrectly. Change
the setting (page 3).
What should I do when the
handset does not turn on?
LMake sure the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
Basic operations
TG7331_7341FX(e)_QG.fm Page 5 Friday, July 11, 2008 9:47 AM

– 6 –
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 17 hours max.
Not in use (standby): 150 hours max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 1 is
displayed, but
3 is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
What should I do to display
caller information?
LYou must subscribe to a Caller ID service. Contact
your service provider/telephone company for
details.
LThe message “You must first subscribe
to Caller ID.” will be displayed until you
receive caller information after subscribing to a
Caller ID service.
What should I do when noise
is heard, sound cuts in and
out?
LYou are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
LMove closer to the base unit.
LIf you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your
DSL/ADSL provider for details.
What should I do when the
operating time seems to be
shorter even after I fully
charged the batteries?
LClean the battery ends (S, T) and the charge
contacts with a dry cloth, and charge again.
Frequently asked questions
Question Cause/solution
TG7331_7341FX(e)_QG.fm Page 6 Friday, July 11, 2008 9:47 AM

– 7 –
What do I need to do to
erase y(Missed call) from
the display?
LThere are unviewed missed calls remaining. View
them and erase yin the following way.
1K(middle soft key)
2{V}/{^}: “Caller List”iM
3Press {V} to search from the most recent call, or
press {^} to search from the oldest call.
Frequently asked questions
Question Cause/solution
TG7331_7341FX(e)_QG.fm Page 7 Friday, July 11, 2008 9:47 AM

– 8 –
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. If for some reason the
handset is not registered to the base unit, re-register the handset.
1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Register H.set”iM
Press and hold {x} for about 5 seconds,
until the registration tone sounds.
LThe next step must completed within
90 seconds.
NKX-TG7331
NKX-TG7341
Wait until “Enter Base PIN”is displayed. i
Enter the base unit PIN (default: “0000”). i
M
LWhen the handset has been registered
successfully, wstops flashing.
Handset
M
Base unit
{x}
{x}
Handset
M
TG7331_7341FX(e)_QG.fm Page 8 Friday, July 11, 2008 9:47 AM

– 9 –
Optional services (Caller ID and SMS)
If you subscribe to a Caller ID service,
caller information will be displayed when a call is received, or
when viewing missed calls.
To use SMS, you must subscribe to a Caller ID and/or an appropriate service
such as SMS.
SMS (Short Message Service)
012345
TG7331_7341FX(e)_QG.fm Page 9 Friday, July 11, 2008 9:47 AM

– 10 –
Notes
TG7331_7341FX(e)_QG.fm Page 10 Friday, July 11, 2008 9:47 AM