Panasonic KX-TG2730S - 2.4 GHz DSS Expandable Cordless... User manual

2.4GHz Multi-Handset Cordless Phone System
Model No. KX-TG2730S
Pulse-or-tone-dialing capability
Operating Instructions
Charge the battery for about 15 hours before initial use.
PLEASE READ BEFORE USE AND SAVE.
Contents:
Location of Controls 2
Connections 5
Battery Installation/Battery Charge 6
Recording a Greeting Message 7
Making/Answering calls with the Handset 8
Making/Answering calls with the Base Unit 9
Caller ID Service 9
Automatic Answering Operation 10
Listening to Messages 10
Important Safety Instructions 11
FCC and Other Information 13

–2–
Please read IMPORTANT SAFETY
INSTRUCTIONS on page 11 before use.
Read and understand all instructions.
Location of Controls
■Handset
INTERCOM
TRANSFER
CLEAR
SP-PHONE
HOLD
FUNCTION
REDIAL
CALLWAIT
2
1
3
4
5
6
78
TONE
0
9
CONF
TALK
OFF
FLASH
PAUS E
Back side
Speaker
Headset Jack
(TONE) Button
(TALK) Button
(Speakerphone)
Button
Button
CONF (Conference)/FUNCTION
Microphone
Charge Contacts
Antenna
Display
(OFF) Button
(HOLD/CLEAR)/
(INTERCOM/TRANSFER)
Button
(PAUSE/REDIAL)
Button
Soft Keys
Navigator Key
( , , , )
(FLASH/CALL!WAIT) Button

–3–
■Base unit
123
ERASE
STOP
HOLDCONF
NEWMESSAGE/SLOWTALK
MAILBOX
MIC
DIGITAL
SPREADSPECTRUM
CHARGE
MULTI HANDSET
0
REDIAL
/
PAUSE
MUTE
TONE
DIGITALSPPHONE
FLASH/
CALL WAIT
1
3
2
456
8
7
9
TRANSFER
INTERCOM
PRIVACY
MEMO
GREETING
PROGRAM RINGER/
AUTO
RINGER
LOUD/
ROOM
MONITOR
IN USE
Display
MIC (Microphone)
CHARGE Indicator
(PROGRAM) Button
(RINGER/AUTO) Button
(DIGITALÒSP-PHONE) Button and
Indicator
(MUTE) Button and Indicator
(FLASH/CALLÒWAIT) Button
(REDIAL/PAUSE) Button
IN USE Indicator
(INTERCOM/TRANSFER)
Button
(PRIVACY) Button and Indicator
(HOLD) Button
(CONF) (Conference) Button

–4–
■Base unit
MIC
CHARGE
ERASE
STOP
MULTI HANDSET
123
NEWMESSAGE/SLOWTALK
MAILBOX
HOLDCONF
REDIAL
/
PAUSE
MUTE
TONE
DIGITAL SPPHONE
FLASH/
CALL WAIT
DIGITAL
SPREADSPECTRUM
TRANSFER
INTERCOM
0
1
3
2
456
8
7
9
PRIVACY
RINGER
LOUD/
MEMO
GREETING
PROGRAMRINGER/
AUTO
ROOM
MONITOR
IN USE
(ERASE) Button (STOP) Button
(GREETING) Button
(ANSWERÒON) Button
and Indicator
(MEMO) Button ROOM MONITOR/INTERCOM
Indicator
Antenna
(TONE) Button
Antenna
Charge
Contacts
(MAILBOX) Buttons
Navigator Key
( , , , )

–5–
Connections
■Connect the AC adaptor and the telephone line cord.
•USE ONLY WITH Panasonic AC ADAPTOR PQLV10.
•The AC adaptor must remain connected at all times. (It is normal for the
adaptor to feel warm during use.)
Hook
Telephone Line Cord
AC Adaptor
Power Outlet (AC 120 V, 60 Hz)
Single-Line Telephone Jack (RJ11C)
Fasten the AC adaptor cord to
prevent it from being
disconnected.
Raise the antennas.

–6–
Battery Installation/Battery Charge
■Recharge
Recharge the battery when:
–"Recharge battery" is displayed,
–" " flashes on the display, or
–the handset beeps every minute while it is in use.
•Clean the handset and the base unit charge contacts with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease,
dust or high humidity. If not, the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the
base unit until "Recharge battery" is displayed and/or " " flashes.
This will maximize the battery life.
•The battery cannot be overcharged.
■Battery installation
1 Install the battery in the handset.
2 Close the handset cover.
■Battery charge
To power the handset, charge the battery.
Place the handset on the base unit for about 15 hours before initial use.
A nickel cadmium battery that is recyclable powers the product
you have purchased. At the end of its useful life, under various
state and local laws, it is illegal to dispose of this battery into
your municipal waste stream. Please call
1-800-8-BATTERY for information on how to recycle this
battery.

–7–
You can record a personal greeting message of up to 2 minutes. If a greeting
message is not recorded, one of two pre-recorded greetings will be played
when a call is received.
•All messages (greeting, incoming, etc.) are stored in digital memory. The
total recording time is about 15 minutes. We recommend you record a
brief greeting message in order to leave more time for recording new
messages.
1 Press and hold (GREETING) until a long beep is heard.
2 After the long beep, talk clearly, about 8 inches (20 cm) away from the MIC
(microphone).
3 When finished, press (GREETING).
•If you do not record a greeting message, one of two messages will be played
when a call is received, depending on the caller’s recording time.
Recording a Greeting Message

–8–
■To make a call
1 Press or .
2 Dial a telephone number.
3 To hang up, press (OFF) or place the handset on the base unit.
•If "No link to base. Walk closer to base and try again" is
displayed and an alarm tone sounds in step 1, move closer to the base unit
or place the handset on the base unit, and try again.
•To redial the last number, press or , then press
(PAUSE/REDIAL).
•To adjust the receiver volume/speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD/CLEAR).
•To release the hold, press (HOLD/CLEAR).
■To answer a call
Press or .
Making/Answering Calls with the Handset

–9–
Making/Answering Calls with the Base Unit
■To make a call
1 Press (DIGITAL!SP-PHONE).
2 Dial a telephone number.
3 Talk into the MIC (microphone).
4 To hang up, press (DIGITAL!SP-PHONE).
•To redial the last number, press (DIGITAL!SP-PHONE), then press
(REDIAL/PAUSE).
•To adjust the speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD).
•To release the hold, press (DIGITAL!SP-PHONE).
■To answer a call
Press (DIGITAL!SP-PHONE), then talk into the MIC (microphone).
Caller ID Service
This unit is compatible with a Caller ID service offered by your telephone
company.
After subscribing to a Caller ID service, the calling party’s information will be
shown on the handset display after the first ring.
The unit can record information of up to 30 different callers in the caller list.
The Caller List information is sorted from the most recent to the oldest call.
When the unit receives the 31st call, the oldest call is deleted.
If your unit is connected to a PBX system which does not support Caller ID
services, you cannot access those services. Please consult your equipment
supplier.

–10–
Automatic Answering Operation
■ How to use the mailboxes
The unit accommodates three mailboxes (Mailbox 1, 2 and 3). A caller can
leave a message in a specified mailbox. If a mailbox is not specified,
messages are recorded in the mailbox 1.
■ When a caller calls
The caller can select a mailbox by pressing (#) and (1) (Mailbox 1), pressing
(#) and (2) (Mailbox 2) or pressing (#) and ( ) (Mailbox 3), while the greeting is
played. The caller can then record a message in the mailbox after a beep.
OR
The caller waits until the greeting finishes, and records a message after a
beep. The message will be recorded in the Mailbox 1.
■ Setting the unit to answer calls
Press (ANSWER!ON) to turn on the answering system.
•The indicator lights and “Answer set”is heard.
Listening to Messages
You can see the total number of recorded messages on the base unit display.
If the ANSWER ON indicator flashes and the mailbox icon(s) ( ,
and ) flash(es) on the display, new messages have been recorded in
the mailbox(es).
To listen to the messages, press (MAILBOX!1), (MAILBOX!2) or (MAILBOX! ).
•When you have new messages, the unit announces the number of new
messages and plays them back.
•When you have no new messages, the unit plays back all recorded
messages.
BOX 3
BOX 2BOX 1