Panasonic DMC-TZ80EB User manual

© Panasonic Corporation 2016.
Unauthorized copying and distribution is a violation
of law.
ORDER NO.DSC1602001CE
B26
Digital Camera
Model No. DMC-TZ80EB
DMC-TZ80EE
DMC-TZ80EF
DMC-TZ80EG
DMC-TZ80EP
DMC-TZ80GA
DMC-TZ80GC
DMC-TZ80GN
DMC-TZ81EG
DMC-ZS60P
DMC-ZS60PP
DMC-ZS60GH
Colours
Product Color
(S)....................Silver Type (Except GC)
(K)....................Black Type

2
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1)---------3
1.4. How to Discharge the Capacitor on Top P.C.B.
Unit-------------------------------------------------------------4
2Warning--------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. How to Replace the Lithium Battery-------------------6
3 Service Navigation------------------------------------------------7
3.1. Introduction --------------------------------------------------7
3.2. Important Notice --------------------------------------------7
3.3. Service Notes -----------------------------------------------9
3.4. General Description About Lead Free Solder
(PbF) -------------------------------------------------------- 10
3.5. How to Define the Model Suffix (NTSC or PAL
model)------------------------------------------------------- 11
4 Specifications ---------------------------------------------------- 16
5 Location of Controls and Components------------------ 18
6 Service Mode ----------------------------------------------------- 19
6.1. Error Code Memory Function ------------------------- 19
7 Troubleshooting Guide---------------------------------------- 22
7.1. Wi-Fi Module (Top P.C.B. Unit) ----------------------- 22
8 Service Fixture & Tools --------------------------------------- 23
8.1. Service Fixture and Tools ------------------------------ 23
8.2. When Replacing the Main P.C.B. -------------------- 23
8.3. Service Position ------------------------------------------ 24
9 Disassembly and Assembly Instructions --------------- 25
9.1. Disassembly Flow Chart-------------------------------- 25
9.2. P.C.B. Location ------------------------------------------- 25
9.3. Disassembly Procedure -------------------------------- 26
9.4. Lens Disassembly Procedure ------------------------- 35
9.5. Assembly Procedure for Lens ------------------------ 37
9.6. Removal of the MOS Unit ------------------------------ 41
10 Measurements and Adjustments -------------------------- 42
10.1. Introduction ------------------------------------------------ 42
10.2. Before Disassembling the unit ------------------------ 42
10.3. Details of Electrical Adjustment----------------------- 44
10.4. After Adjustment------------------------------------------ 51
11 Maintenance ------------------------------------------------------ 52
11.1. Cleaning Lens, Viewfinder and LCD Panel -------- 52
12 Block Diagram --------------------------------------------------- 53
12.1. Overall Block Diagram ---------------------------------- 53
12.2. System Control Block Diagram ----------------------- 54
12.3. Audio/Video Process/ HDMI Block Diagram ------ 55
12.4. Lens/Flash Block Diagram ----------------------------- 56
12.5. Power (1) Block Diagram------------------------------- 57
12.6. Power (2) Block Diagram------------------------------- 58
13 Wiring Connection Diagram -------------------------------- 59
13.1. Interconnection Schematic Diagram ---------------- 59
14 Schematic Diagram -------------------------------------------- 61
15 Printed Circuit Board------------------------------------------ 61
16 Exploded View and Replacement Parts List----------- 61

3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is
essential that these critical parts should be replaced with
manufacturer's specified parts to prevent X-RADIATION,
shock fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from
accidents resulting in personal injury from electrical
shocks. It will also protect AC Adaptor from being
damaged by accidental shorting that may occur during
servicing.
3. When servicing, observe the original lead dress. It a short
circuit is found, replace all parts which have been
overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed
metallic cabinet part on the equipment such as
screwheads, connectors, control shafts, etc. When the
exposed metallic part has a return path to the chassis, the
reading should be between 1Mand 5.2M. When the
exposed metal does not have a return path to the chassis,
the reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5k, 10 W resistor, in parallel with a 0.15F
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 mA. In case a measurement
is outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure 1

4
1.4. How to Discharge the Capacitor on Top P.C.B. Unit
CAUTION:
1. Be sure to discharge the capacitor on Top P.C.B. Unit.
2. Be careful of the high voltage circuit on Top P.C.B. Unit when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Install the insulation tube onto the lead part of Resistor (ERG5SJ102:1k/5W).
(an equivalent type of resistor may be used.)
3. Place a resistor between both terminals of capacitor on the Top P.C.B. Unit for approx. 5 seconds.
4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1

5
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

6
2.3. How to Replace the Lithium Battery
2.3.1. Replacement Procedure
1. Remove the Battery P.C.B. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. B9401 at foil side of Battery P.C.B.)
and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
Note:
The Lithium battery includes electric lead terminals.
Note:
The lithium battery is a critical component.
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
Note:
Above caution is applicable for a battery pack which is for DMC-TZ80/TZ81/ZS60 series, as well.

7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which will allow service personnel's to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. Important Notice
3.2.1. About lens block
The image sensor (MOS) unit which are connected to the lens unit with 3 screws. 2 of these 3 screws are locked, after performing
the Optical tilt adjustment. During servicing, if one of MOS fixing screws are loosened, the Optical tilt adjustment must be
performed. (About the Optical tilt adjustment, refer to the "10.3.2 Adjustment Specifications" for details.)
• Using the Extension cable, perform the Optical tilt adjustment according to the following procedure.
1. Remove the Frame Plate Unit. (Refer to Disassembly
Procedures.)
2. Remove the Speaker from the Frame.
3. Using the Rear Operation FPC, connect the Main
P.C.B. to Rear Operation P.C.B. Unit.
4. Using the Extension cable, connect the Main P.C.B. to
LCD Unit.
5. Using the Extension cable, connect the Main P.C.B. to
Lens Unit Flex.
6. Insulation Sheet is inserted between the LCD Unit,
Rear Operation P.C.B. Unit and the Main P.C.B.
7. The Main P.C.B. is lifted, perform the Optical tilt
adjustment.

8
3.2.2. About VENUS ENGINE (IC6001) < Located on the Main P.C.B. >
• The VENUS ENGINE (IC6001) consists of two IC chips, which are fixed together with solder.
(It is so called, "Package On Package" type of IC.)
Caution:
• During servicing, do not press down hard on the surface of IC6001.
3.2.3. About Flash ROM (IC6003) and Charging Control Microcomputer (IC1502)
When the Flash Rom or Charging Control Microcomputer is replaced, it is need to adjust the firmware of the Charging Control
Microcomputer to the one of the Flash ROM.
For details, refer to "10.3.2. Adjustment Specifications".
It may takes about 10 seconds. While doing the adjustment, don't turn the power off forcibly.
(It cause the Charging Control Microcomputer crush, then the camera can not turn on.)
3.2.4. About Flexible Cable and Connector
Do not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.
Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.

9
3.3. Service Notes
3.3.1. About Wi-Fi Function
The page number in this chapter does not show the page number of this service manual.
3.3.2. Important Notice of Servicing
This Camera unit has the personal information of wireless LAN connection the customer has registered.
For the protection of private information, please erase the personal information after the completion of repair by "INITIAL
SETTING".
In addition, please print out the following documents, and pass to the customer with the Camera unit.
Printing Material [Leaflet for Customer]

10
3.4. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 °C (86 °F) more than that of the
normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
• (Definition: The letter of is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 °C
(662±86 °F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
SVKZ000001-----------(0.3mm 100g Reel)
SVKZ000002-----------(0.6mm 100g Reel)
SVKZ000003-----------(1.0mm 100g Reel)
Note:
* Ingredient: Tin (Sn) 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%. (Flex cored)
The letter of is printed either foil side or components side on the P.C.B. using the lead free solder.
(See right figure)

11
3.5. How to Define the Model Suffix (NTSC or PAL model)
There are six kinds of DMC-TZ80/TZ81/ZS60, regardless of the colours.
• a) DMC-TZ85 (Japan domestic model.)
• b) DMC-ZS60P/PP
• c) DMC-TZ80EB/EF/EG/EP, TZ81EG
• d) DMC-TZ80EE
• e) DMC-TZ80GN
• f) DMC-TZ80GA/GC, ZS60GH
What is the difference is that the "INITIAL SETTINGS" data which is stored in Flash ROM mounted on Main P.C.B.
3.5.1. Defining methods
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
Note:
After replacing the Main P.C.B., be sure to achieve adjustment.

12
3.5.2. INITIAL SETTINGS:
After replacing the Main P.C.B. and/or Flash-ROM, make sure to perform the initial settings after achieving the adjustment by
ordering the following procedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTION.
2. PROCEDURES:
• Precautions: Read the above "CAUTION" carefully.
• Preparation:
1. Attach the fully charged Battery.
2. Set the mode dial to the PROGRAM AE mode.
* If the mode dial position is other than PROGRAM AE mode, it does not display the initial settings menu.
•Step 1. The temporary cancellation of "INITIAL SETTINGS":
While keep pressing "RIGHT of Cursor button", MENU/SET button and DISPLAY button simultaneously, turn the Power on.
•Step 2. The cancellation of "INITIAL SETTINGS":
Press PLAYBACK button to switch to the playback screen. (Keep pressing the button.)
Press " UP of Cursor button" additionally, then turn the Power off.
The LCD displays the " ! " mark before the unit powers down.
•Step 3. Turn the Power on:
Turn the Power on.

13
•Step 4. Display the "INITIAL SETTINGS" menu:
* If the unit is other than PROGRAM AE mode, it does not display the initial settings menu.
While keep pressing MENU/SET and “ RIGHT of Cursor button" simultaneously, turn the Power off.
The "INITIAL SETTINGS" menu is displayed.
There are two kinds of "INITIAL SETTINGS" menu form as follows:
[CASE 1. After replacing MAIN P.C.B.]
There are three kinds of menu from as follows:
[Except for "DMC-TZ80EG, EF, EB, EP and TZ81EG" models : (SEP0684AC is used as a Main P.C.B.)]
When Main P.C.B. has just been replaced, all of the model suffix are displayed as follows. (Three pages in total)
[Only for "DMC-TZ80EG, EF, EB, EP and TZ81" models : (SEP0684AD is used as a Main P.C.B.)]
When Main P.C.B. has just been replaced, only 5 model suffix are displayed as follows. (Two pages in total)
To display the "TZ81" model suffix, press the DELETE button.

14
[CASE 2. Other than "After replacing Main P.C.B."]
To display the "TZ81" model suffix, press the DELETE button.
•Step 5. The cancellation of "STRICT MODE":
Press DISPLAY button, then Strict in the upper right corner of the LCD display will disappear.
•Step 6. Chose the model suffix in "INITIAL SETTINGS": (Refer to "CAUTION")
[Caution: After replacing Main P.C.B.]
(Especially, other than "DMC-TZ80EG/EF/EB/EP and DMC-TZ81" models)
The model suffix can be chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.
Therefore, select the area carefully.
Select the area with pressing "UP / DOWN of Cursor buttons".

15
•Step 7. Set the model suffix at "INITIAL SETTINGS":
Press the "RIGHT of Cursor buttons".
The only set area is displayed. Press the "RIGHT of Cursor buttons" after confirmation.
(The unit is powered off automatically.)
Note:
It may cause the following error indication without cancellation of "STRICT MODE".
In this case, press DISPLAY button after disappearing error indication.
•Step 8. CONFIRMATION:
Confirm the display of "PLEASE SET THE CLOCK" in concerned language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
1) As for your reference, major default setting condition is as shown in the following table.
• Default setting (After "INITIAL SETTINGS")
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-TZ85 (Japan domestic model) NTSC Japanese Year/Month/Date
b) DMC-TZ80EB PAL English Date/Month/Year
c) DMC-TZ80EE PAL Russian Date/Month/Year
d) DMC-TZ80EF PAL English Date/Month/Year
e) DMC-TZ80EG PAL English Date/Month/Year
f) DMC-TZ80EP PAL English Date/Month/Year
g) DMC-TZ80GA PAL English Date/Month/Year
h) DMC-TZ80GC PAL English Date/Month/Year
i) DMC-TZ80GN PAL English Date/Month/Year
j) DMC-TZ81EG PAL English Date/Month/Year
k) DMC-ZS60P NTSC English Month/Date/Year
l) DMC-ZS60PP NTSC English Month/Date/Year
m) DMC-ZS60GH PAL English Date/Month/Year

16
4 Specifications
The following specification is for DMC-ZS60P/PP, ZS100P/PP.
Some specifications may differ depending on model suffix.

17

18
5 Location of Controls and Components
The following description is for DMC-ZS60P/PP, ZS100P/PP.
Some description may differ depending on model suffix.
The page number in this chapter does not show the page number of this service manual.

19
6 Service Mode
6.1. Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to Flash ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
•Preparation:
1. Attach the fully charged Battery, and insert the memory card (32MB or more).
2. Set the mode dial to the PROGRAM AE mode.
Note:
*Since this unit has built-in memory, it can be performed without inserting Memory Card.
•Step 1. The temporary cancellation of "INITIAL SETTINGS":
While keep pressing "RIGHT of Cursor button", MENU/SET button and DISPLAY button simultaneously, turn the Power on.
•Step 2. Execute the error code display mode:
Press the "PLAYBACK button, "LEFT of Cursor button" and MENU/SET button simultaneously.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display Error code display CAMERA INFO Normal display .....

20
3. Error Code List
The error code consists of 8 bits data and it shows the following information.
Attribute Main item Sub item Error code Contents (Upper) Error Indication
High
4 bits
Low
4 bits
Check point (Lower) Detecting
device
Part/Circuit
LENS Lens drive Focus 1C*0 0?01 HP High detect error
(Focus encoder always detects High, and not becomes
Low)
FOCUS L LENS FPC/
DSP
Mechanical lock, FP9004-(43) signal line or IC6001
(VENUS ENGINE)
0?02 HP Low detect error
(Focus encoder always detects Low, and not becomes
High)
FOCUS H
Mechanical lock, FP9004-(43) signal line or IC6001
(VENUS ENGINE)
Zoom 0?10 Collapsible barrel Low detect error
(Collapsible barrel encoder always detects High.)
ZOOM L ZOOMm/
LENSu
Mechanical lock, FP9004-(43) signal line or IC6001
(VENUS ENGINE)
0?20 Collapsible barrel High detect error
(Collapsible barrel encoder always detects Low.)
ZOOM H
Mechanical lock, FP9004-(43) signal line or IC6001
(VENUS ENGINE)
0?30 Zoom motor sensor error. (Initialized or Terminated) ZOOM ENC
Mechanical lock, FP9004-(4) signal line or IC6001
(VENUS ENGINE)
0?40 Zoom motor sensor error. (During monitor mode.)
Mechanical lock, FP9004-(4) signal line or IC6001
(VENUS ENGINE)
0?50 Zoom motor sensor error. (During monitor mode with slow
speed.)
Mechanical lock, FP9004-(4) signal line or IC6001
(VENUS ENGINE)
0?60 Detection of zoom misregistration by impact such as fails. (No indication) (No indication)
Lens Unit
OIS 1000 PSD (X) error. Hall element (X axis) position detect error in
OIS unit.
OIS X LENSu NG
OIS Unit
2000 PSD (Y) error. Hall element (Y axis) position detect error in
OIS unit.
OIS Y
OIS Unit
3000 GYRO (X) error. Gyro (IC7101 : X axis) detect error on
Main P.C.B.
GYRO X GYRO NG
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
4000 GYRO (Y) error. Gyro (IC7101 : Y axis) detect error on
Main P.C.B.
GYRO Y
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
5000 GYRO (R) error, Gyro (IC7101 : R axis) detect error on
Main P.C.B.
GYRO R
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
6000 Drive voltage (X) error. OISX REF LENSu/LENS
FPC
LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE)
AD value error, etc.
7000 Drive voltage (Y) error. OISY REF
LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE)
AD value error, etc.
8000 OIS GYRO - Digital communication error. (No indication) (No indication)
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
Lens 18*1 0000 Power ON time out error. LENS DRV LENSu
Lens drive system
18*2 0000 Power OFF time out error.
Lens drive system