Panasonic KX-FP105RS User manual

©2000 Kyushu Matsushita Electric Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
KX-FP105RS
(for Russia)
Compact Plain Paper FAX
Please file and use this manual together with the service manual for Model No. KX-FP101AL, Order
No.KM79909316C3. This Service Manual indicates the main differences between; Original KX-FP101AL
and KX-FP105RS.
ORDER NO. KMF0002387A3

1 INTRODUCTION
1.1. AC CAUTION
Change from original page 4 (1.5. AC CAUTION)
For safety, before closing the lower cabinet, please make sure of the following precautions.
1.The earth lead is fixed with the screw.
2.The AC connector is connected properly.
3.Wrap the earth lead around the core 3 times.
(Bottom View)
1.2. PERSONAL SAFETY PRECAUTIONS
1.2.1. LIVE ELECTRICAL SECTIONS
Change from original page 4 (1.6.2. LIVE ELECTRICAL SECTIONS)
All the electrical sections of the unit supplied with AC power by the AC power cord are live.
Never disassemble the unit for service with the AC power supply plugged in.
CAUTION:
AC voltage is supplied to the primary side of the power supply unit. Therefore, always unplug the AC power cord before
disassembling for service.
(Bottom View)
2
KX-FP105RS

Change from original page 6 (1.8. FEATURES)
General
· Help function
Display:
1.HOW TO SET UP
2.EASY DIAL
3.FAX RECEIVING
· LCD (Liquid Crystal Display) readout
· TAM (Telephone answering machine) interface
Plain Paper Facsimile Machine
· 12 second transmission speed *
· A4, G3 compatible
· Automatic document feeder (15 sheets)
· 6 stations one-touch dialer
· Broadcast (up to 20 station) × 3
· Resolution : Standard/Fine/Super fine/Half tone (64 level)
· LCD Contrast : Normal/Darker
· Delayed transmission
· Overseas transmission function
· Remote FAX receiving using an extension phone
· 150-sheet paper capacity
· Automatic fax/phone switching
· Distinctive ring detection **
* The 12 second speed is based upon the ITU-T Test Chart on
the condition that memory transmission is performed.
** Subscription to distinctive ring services required.
Large Memory (28 pages) ... Performed by DRAM
Approx. 28 pages of memory reception
Approx. 25 pages of memory transmission
Integrated Telephone System
· On-hook dialing
· Monitor
· Voice muting
· Redialing function
· 100-Station telephone directory with Easy Dial
Copier function
· Multi-copy function (up to 99 copies)
· Enlargement and reduction
· Collate
· 64-Level halftone
· Electronic film indicator
1.3. FEATURES
3
KX-FP105RS

1.4. SPECIFICATIONS
Change from original page 7 (1.9. SPECIFICATIONS)
Applicable Lines: Public Switched Telephone Network
Document Size: Max. 216 mm (8 1/2") in width
Max. 600 mm (23 5/8") in length
Effective Scanning Width: 208 mm (8 3/16")
Recording Paper Size: A4: 210×297 mm (8 1/4"×11 11/16")
Effective Printing Width: 202 mm (7 15/16")
Transmission Time*: Approx. 12 sec./page (Original mode)**
Approx. 30 sec./page (G3 Normal mode)
Scanning Density: Horizontal:
8 pels/mm (203 pels/inch)
Vertical:
3.85 lines/mm (98 lines/inch)—STANDARD mode
7.7 lines/mm (196 lines/inch)—FINE/HALF TONE mode
15.4 lines/mm (392 lines/inch)—SUPER FINE Mode
Halftone Level: 64-level
Scanner Type: Contact Image Sensor (CIS)
Printer Type: Thermal Transfer Printing
Data Compression System: Modified Huffman (MH), Modified READ (MR), Modified Modified READ (MMR)
Modem Speed: 9,600/7,200/4,800/2,400 bps; Automatic Fallback
Operating Environment: 5—35°C (41—95°F), 20—80% RH(Relative Humidity)
Dimensions (H×W×D): 143×325×305 mm (5 5/8"×12 13/16"×12")
Mass (Weight): Approx. 4.0 kg (8.8 lb.)
Power Consumption: Standby: Approx. 6.5 W
Transmission: Approx. 15 W
Reception: Approx. 42 W (When receiving a 20% black document)
Copy: Approx. 45 W (When copying a 20% black document)
Maximum: Approx. 150 W (When copying a 100% black document)
Power Supply: 220—240 V AC, 50/60 Hz
Memory Capacity: Approx. 28 pages memory reception
Approx. 25 pages memory transmission
(Based on CCITT Test Chart in standard resolution, without using Error Correction
Mode.)
* Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the receiving
unit.
** The 12 second speed is based upon the CCITT Test Chart and original mode. (Refer to "1.11. CCITT Test Chart".) If the
capability of the other party’s machine is inferior to your unit, the transmission time may be longer.
Note:
· Any details given in these instructions are subject to change without notice.
· The pictures and illustrations in these instructions may vary slightly from the actual product.
Design and specifications are subject to change without notice.
4
KX-FP105RS

1.5. CCITT Test Chart
Change from original page 8 (1.11. ITU-T Test Chart (Actual size))
5
KX-FP105RS

1.6. LOCATION OF CONTROLS
1.6.1. OVERVIEW
Change from original page 9 (1.12.1. OVERVIEW)
Note:
· The document and recording paper will be ejected from the front of the unit. Do not put anything in front of the unit.
6
KX-FP105RS

1.6.2. CONTROL PANEL
Change from original page 10 (1.12.2. CONTROL PANEL)
7
KX-FP105RS

1.7. CONNECTIONS
Change from original page 11 (1.13. CONNECTIONS)
Note:
When you operate this product, the power outlet should be near the product and easily accessible.
8
KX-FP105RS

1.8. INSTALLATION
1.8.1. TO SELECT CHARACTERS WITH THE DIAL KEYPAD
Change from original page 18 (1.14.10. TO SELECT CHRACTERS WITH THE DIAL KEYPAD)
Note: A hyphen entered in a telephone number is counted as two digits.
9
KX-FP105RS

2 TROUBLESHOOTING GUIDE
2.1. PROGRAM MODE TABLE
Change from original pages 60, 61 ([2. Program Mode Table] in 2.3.3.3.2. Remote programming)
2. Program Mode Table
Code Function Set Value Default Remote
Setting
001 Set date and time mm/dd/yy hh:mm Jan/01/99 NG
002 Your logo --------- None NG
003 Your telephone number --------- None NG
004 Transmission report mode 1:Error / 2:ON / 3:OFF Error OK
006 FAX ring count 1~5 1OK
012 Remote TAM activation 1:ON / 2:OFF OFF ID=11 OK
013 Dialing mode 1:Pulse / 2:Tone Tone OK
018 Film remain --------- --------- NG
022 Auto journal print 1:ON / 2:OFF ON OK
023 Overseas mode ON / OFF OFF NG
025 Delayed transmission ON / OFF OFF NG
030 Silent FAX recognition ring 3 to 6 rings 3OK
031 Distinctive ring 1:OFF / 2:A / 3:B / 4:C / 5:D OFF OK
036 Rx reduction 1:72% / 2:86% / 3:92% / 4:100% 92% OK
039 LCD contrast 1:Normal / 2:Darker Normal OK
040 Silent detection 1:ON / 2:OFF ON OK
041 Remote FAX activation code ON / OFF ON ID=*9 NG
044 Receive alert 1:ON / 2:OFF ON OK
046 Friendly receive 1:ON / 2:OFF ON OK
049 Auto disconnect ON / OFF ON NG
058 Original setting 1:Normal / 2:Light / 3:Darker Normal OK
068 ECM selection 1:ON / 2:OFF ON OK
070 FAX pager ON / OFF OFF NG
076 FAX tone 1:ON / 2:OFF ON OK
077 Auto answer mode 1:FAX Only 2:TEL/FAX FAX Only OK
078 TEL/FAX ring 1 to 4 rings 1OK
079 Film detection 1:ON / 2:OFF ON OK
080 Set default YES / NO NO NG
501 Pause time set 001~600 x 100msec 050 OK
502 Flash time 01~99 x 10msec 070 OK
503 Dial speed 1:10pps / 2:20 pps 10pps OK
511 Vox sense 1:HIGH / 2:LOW HIGH OK
520 CED frequency select 1:2100Hz / 2:1100Hz 2100 OK
521 International mode select 1:ON / 2:OFF ON OK
522 Auto standby select 1:ON / 2:OFF ON OK
523 Receive equalizer select 1:0km / 2:1.8km / 3:3.6km / 4:7.2km 0km OK
524 Transmission equalizer select 1:0km / 2:1.8km / 3:3.6km / 4:7.2km 0km OK
550 Memory clear --------- --------- NG
551 ROM check --------- --------- NG
552 DTMF signal tone test ON / OFF OFF NG
553 Monitor on FAX communication 1:OFF / 2:Phase B / 3:ALL OFF OK
554 Modem test --------- --------- NG
555 Scanner test --------- --------- NG
556 Motor test --------- --------- NG
557 LED test --------- --------- NG
558 LCD test --------- --------- NG
559 Document jam detection 1:ON / 2:OFF ON OK
561 Key test --------- --------- NG
570 Break % select 1:61% / 2:67% 61% OK
571 ITS auto redial time set 00~99 14 OK
572 ITS auto redial line disconnection time set 001~999 30 OK
573 Remote turn-on ring number 01~99 15 OK
590 FAX auto redial time set 00~99 05 OK
591 FAX auto redial line disconnection time set 001~999sec 045 OK
592 CNG transmit select 1:OFF / 2:ALL / 3:AUTO ALL OK
593 Time between CED and 300 bps 1:75ms / 2:500ms / 3:1sec 75ms OK
594 Overseas DIS detection 1:1st / 2:2nd 1st OK
10
KX-FP105RS

Code Function Set Value Default Remote
Setting
595 Receive error limit value 001~999 100 OK
596 Transmit level set -15~00dBm -10 OK
598 Receiving Sensitivity 20~48 43 OK
599 ECM frame size 1: 256 byte / 2: 64 byte 256 byte OK
602 Warning list printing 1:ON / 2:OFF ON OK
700 EXT. TAM OGM Rec. time 01~99sec 10sec OK
701 No voice detect time 01~99X100msec 50 OK
717 Transmit speed select 1:9600/ 2:7200/ 3:4800/ 4:2400 9600bps OK
718 Receive speed select 1:9600/ 2:7200/ 3:4800/ 4:2400 9600bps OK
719 Ringer off in TEL/FAX mode 1:ON / 2:OFF ON OK
721 Pause tone detect 1:ON / 2:OFF ON OK
722 Redial tone detect 1:ON / 2:OFF ON OK
745 Power on film feed 1:ON / 2:OFF ON OK
763 CNG detect time for friendly reception 1:10s / 2:20s / 3:30s 30s OK
771 T1 timer 1:35s / 2:60s 35s OK
774 T4 Timer 00~99 X100ms 00 OK
815 Sensor & VOX test --------- --------- NG
852 Print test pattern --------- --------- NG
853 Top margin 1~9 --------- OK
854 Left margin 1~8 --------- OK
861 A4 size set 1:ON / 2:OFF ON OK
880 History list 1:Start --------- NG
890 TEL/FAX ring back tone 1:ON / 2:OFF ON OK
991 Setup list 1:Start --------- OK
994 Journal list 1:Start --------- OK
995 Journal 2 list 1:Start --------- OK
996 Journal 3 list 1:Start --------- OK
998 History list 1:Start --------- OK
999 Service list 1:Start --------- OK
OK means "can set".
NG means "can not set".
Note:
Refer to 2.4.4. SERVICE FUNCTION TABLE for descriptions of the individual codes.
Example:
If you want to set value in the "004 Transmission report mode", press the dial key number ,or corresponding to the Set
Value you want to select. (1:ERROR/2:ON/3:OFF)
11
KX-FP105RS

2.2. Digital Block Diagram Change from original page 63 (2.3.3.4.1. Digital Block Diagram)
IC501
ASIC
ADR[15:13]
RBA[6:0]
ADR[12:0]
DB[7:0]
XRD
XWR
XROMCS
XRAMCS
XMDMCS
IC502
ROM IC504 SRAM IC505 MODEM
A[17:0]
D[7:0]
XRD
XCS
A[16:0]
D[7:0]
XRD
XWR
XCS
A[4:0]
D[7:0]
XRD
XWR
XCS
XWDERR
INOUTGND
+5V
+3.3V
TO
OP-PANEL
KSTART,KLATCH
KSCLK,KTXD
KRXD,JOG1,JOG2
TO
CIS
F1,FTG
CISLEDON
VIDEO
TO
THRMAL
HEAD
THDAT,THCLK,THLAT
STB1,STB2,STB3
TM
+24V
TO
MOTOR
TM[3:0],TXE
TO
POWER
SUPPLY
+24V,+5V,PG,DG
OP-RESET
+24V
PDET
XRESETI
XORESET
XRESET
XBACKEN
RESET-
IC
+3V/BATT
+5V/BATT
VCC
BATT
+
-
24MHz
32.768KHz
TX
RX
TO
ANALOG
PCB
SP-AMP
TO
SPEAKER
A[12:0]
RBA[5:0]
A[11:0]
RBA[2:0]
A[4:0]
+5V
XRAS
XCAS
A[9:0]
D[7:0]
XRD
XWR
XRAS
XCAS
IC503
DRAM
A[7:4]
RBA[5:0]
FILMEND
PAPER
TOP
SENSOR
LED ON
PS501
32.256MHz
TO
POSITIO
N
SW
+5V
CN505
CN504
CN508
CN507
CN506
CN509
PS501
CN503
BA
G
DIR
IC550
CN501,502
MIDATA
MICLK
MILAT
IC551
ANALOG ASIC
You also need to check the signal lines listed here [List 1] when the unit fails to boot up the system. Those signal lines should remain normal. Other signal lines are not directly related to that failure even if they have faults or troubles.
12
KX-FP105RS

2.3. Analog Board Section
Change from original pages 71, 72 (2.3.3.5. Analog Board Section)
This chapter provides the testing procedures required for the analog parts. A signal route to be tested is determined depending
upon purposes. For example, the handset TX route begins at the handset microphone and the signal is output to the telephone line.
The signal mainly flowing on this route is analog. You can trace the signal with an oscilloscope. The signal flow on each route is
shown in the Check Sheet here. If you find a specific problem in the unit, for example if you cannot communicate with the H/S, trace
that signal route locally with the following Check Sheet and locate the faulty point.
Note:
{ }: Inside the digital board
13
KX-FP105RS

1.Defective ITS (Integrated Telephone System) Section
a.No handset and monitor
Perform a signal test in the ITS or the NCU section and locate a defective point (where the signal disappears) on each
route between the handset microphone and telephone line (sending), or between the telephone line and the handset
speaker (receiving), or between the telephone line and the speaker (monitor). Check the components at that point. "CHECK
SHEET" in 2.3.3.5. Analog Board Section is useful for this investigation.
b.No pulse dialing
c.No ring tone (or No bell)
d.No tone dialing
14
KX-FP105RS

2.4. USER MODE (The list below is an example of the SYSTEM SETUP
LIST the unit prints out.)
Change from original page 83 (2.4.3. USER MODE (The list below is an example of the SYSTEM SETUP LIST the unit prints
out. ) )
Note:
The above values are the default values.
15
KX-FP105RS

2.5. SERVICE FUNCTION TABLE
Change from original pages 84, 85 (2.4.4. SERVICE FUNCTION TABLE)
Code Function Set Value Effective Range Default Remarks
501 Pause time set X 100 msec 001~600 50 ----------
502 Flash time set X 10 msec 01~99 70 ----------
503 Dial speed select 1:10 pps 2:20 pps 1, 2 1 ----------
511 Vox sense 1:High 2:Low 1, 2 1When the TAM (or EXT TAM) does not
stop recording the ICM because noise is
detected on the telephone line, change
this setting to "LOW".
520 CED frequency select 1:2100 Hz 2:1100 Hz 1, 2 1See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
521 International mode select 1:ON 2:OFF 1, 2 1See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
522 Auto standby select 1:ON 2:OFF 1, 2 1The resolution reverts to the default when
transmission is complete.
523 Receive equalizer select 1:0.0km 2:1.8km
3:3.6km 4:7.2km 1~4 1When the telephone station is far from the unit or reception cannot be performed
correctly, adjust accordingly.
524 Transmission equalizer select 1:0.0km 2:1.8km
3:3.6km 4:7.2km 1~4 1When the telephone station is far from the unit or reception cannot be performed
correctly, adjust accordingly.
550 "Memory clear: To reset the value to the default one, except the top margin (853) and left
margin (854)." “START” input
552 DTMF single tone test 1:ON 2:OFF 1, 2 2See 2.5. TEST FUNCTIONS.
553 Monitor on FAX communication
select 1:OFF 2:PHASE B
3:ALL
1~3 1Sets wherher to monitor the line signal
with the unit´s speaker during FAX
communication or not.
554 Modem test See 2.5. TEST FUNCTIONS.
555 Scan check See 2.5. TEST FUNCTIONS.
556 Motor test 0 See 2.5. TEST FUNCTIONS.
557 LED test See 2.5. TEST FUNCTIONS.
558 LCD test See 2.5. TEST FUNCTIONS.
559 Document jam detection select 1:ON 2:OFF 1, 2 1See 2.2.1. Paper Jam.
561 KEY test See 2.5. TEST FUNCTIONS.
570 BREAK % select 1:61% 2:67% 1, 2 1Sets the % break of pulse dialing
according PBX.
571 ITS auto redial time set X number of times 00~99 14 Selects the number of times that ITS is
redialed (not including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 30 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of rings 01~99 15 Sets the number of rings before the unit
starts to receive a document in the TEL
mode.
590 FAX auto redial time set X number of times 00~99 5Selects the number of redial times during
FAX communication (not including the first
dial).
591 FAX auto redial time disconnection
time set X second 001~999 45 Sets the FAX redial interval during FAX communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO
1~3 2Lets you select the CNG output during
FAX transmission.
ALL: CNG is output at phase A.
AUTO: CNG is output only when
automatic dialing is performed.
OFF: CNG is not output at phase A.
593 Time between CED and 300bps 1: 75 msec
2:500 msec
3:1 sec
1~3 1See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
594 Overseas DIS detection select 1:detects at the 1st time
2:detects at the 2nd time 1, 2 1See Symptom/Countermeasure Table for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
595 Receive error limit value set X Number of times 001~999 100 Sets the number of acceptable error lines
when the FAX reconstructs the received
data.
596 Transmit level set X dBm - 15~00 -10 Selects the FAX transmission level.
598 Receiving sensitivity 43= -43 dBm 20~48 43 Used when there is an error problem.
599 ECM frame size 1:256 2:64 1, 2 1See 2.2.1. Paper jam
602 Warning LIST Printing 1:ON 2:OFF 1, 2 1Used to print a caution list when setting
the TEL/FAX mode and ring detection.
700 EXT. TAM OGM Rec.time X second 01~99 10 Set the start time of silent detection.
16
KX-FP105RS

Code Function Set Value Effective Range Default Remarks
701 No voice detect time X100 msec 01~99 50 Sets the silent call confirmation
detection time.
717 Transmit speed selection 1:9600BPS 2:7200BPS
3:4800BPS 4:2400BPS 1~4 1Adjusts the speed to start training during FAX transmission.
718 Receive speed selection 1:9600BPS 2:7200BPS
3:4800BPS 4:2400BPS 1~4 1Adjusts the speed to start training during FAX reception.
719 Ringer off in TEL/FAX mode 1:ON 2:OFF 1, 2 1Sets the ringer switch off when a call is
received in the TEL/FAX mode.
721 Pause tone detect 1:ON 2:OFF 1, 2 1Selects the tone detection for pause in
dialing.
722 Redial tone detect 1:ON 2:OFF 1, 2 1Selects the tone detection mode after
redialing.
745 Power ON film feed 1:ON 2:OFF 1, 2 1When the power is turned on, the film is
wound to take up any slack.
763 CNG detect time for friendly
reception 1:10 sec 2:20 sec
3:30 sec
1~3 3Selects the CNG detection tome of
friendly reception.
771 T1 timer 1:35 sec
2:60 sec 1, 2 1Sets a higher value when the response from the other party needs more time
during FAX transmission.
774 T4 Timer 00~99(X100 msec) 00~99 0Use this function when delay occurs
on the line and communication does
not work well.
815 Sensor & Vox check See 2.5. TEST FUNCTIONS.
852 Print test pattern See 2.5. TEST FUNCTIONS.
853 Top margin 1~9 -------- ----------
854 Left margin 1~8 -------- ----------
861 A4 size set 1:ON 2:OFF 1, 2 1Use only at the factory.
880 History list See 2.4.6. HISTORY.
881 Journal 2 list See 2.4.7.3. PRINTOUT EXAMPLE.
882 Journal 3 list See 2.4.7.3. PRINTOUT EXAMPLE.
890 TEL/FAX ring back tone 1:ON 2:OFF 1, 2 1Selects whether the TEL/FAX 1st ring
back tone is ON or OFF in the TEL/FAX
mode.
17
KX-FP105RS

2.6. SERVICE MODE SETTINGS (Example of a printed out list)
Change from original page 86 (2.4.5. SERVICE MODE SETTINGS (Example of a printed out list))
Note:
The above values are the default values.
18
KX-FP105RS

2.7. Descriptions of the HISTORY Report
Change from original page 88 (2.4.6.1. Descriptions of the HISTORY Report)
(1) ROM VERSION
EPROM version
(2) SUM
EPROM internal data calculation.
(3) YOUR LOGO
The user logo recorded in the unit. If it is not recorded, NONE will be displayed.
(4) YOUR TELEPHONE NUMBER
The user telephone number recorded in the unit. If it is not recorded, NONE will be displayed.
(5) FAX PAGER NUMBER
If you program a pager number into the unit, the pager number will be displayed here.
(6) FACTORY - CUSTOMER
This shows how many days from factory production until the user turns ON the unit.
(7) MONTH
The shows the very first month, date, year and time set by the user after they purchased the unit.
(8) DAY
The shows the very first month, date, year and time set by the user after they purchased the unit.
(9) YEAR
The shows the very first month, date, year and time set by the user after they purchased the unit.
(10) TIME
The shows the very first month, date, year and time set by the user after they purchased the unit.
(11) USAGE TIME
The amount of time the unit has been powered ON.
(12) FACTORY - NOW
This shows how many days from factory production until the user prints out this history list.
(13) TEL MODE
The amount of time the TEL mode setting was used.
(14) FAX MODE
The amount of time the FAX mode setting was used.
(15) TEL/FAX MODE
The amount of time the TEL/FAX mode setting was used.
(16) ANS/FAX MODE
The amount of time the ANS/FAX mode setting was used.
(17) FINAL RECEIVE MODE
The last set receiving mode by the user.
(18) TONE/PULSE SELECTION
The most recently used setting used, either TONE or PULSE.
(19) RECEIVE REDUCTION
The compression rate when receiving.
(20) SETTING NO. OF DIRECTORY
The recorded directory stations (one touch and JOG DIAL).
(21) NUMBER OF COPY
The number of pages copied.
(22) NUMBER OF RECEIVE
The number of pages received.
(23) NUMBER OF SENDING
The number of pages sent.
(24) Not Used
19
KX-FP105RS

2.8. BUTTON CODE TABLE
Change from original page 97 (2.5.2. BUTTON CODE TABLE)
Note:
These codes (00, 01) are only for the data in the History Report.
20
KX-FP105RS