Panasonic TC26LX20 - 26" LCD TV User manual

Panasonic
LCD TV
Operating Instructions
Model No,
For assistance, please call : %800o21%PANA (7262)
or send eoraaH to : [email protected]
or vUsit us at www.panasonBc.com (U.S.A.}
For assistance, pmease call : 787-750-4300
or vUsUtus at www.panasonBc.com (Puerto Rico}
For assistance, pmease call : 1-800-561 °5505
or visit us at www.panasonic.ca (Canada)
Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference,
/ EspaSoJ-) [Resumen] TQBOOZSt

CAUTmON
A The lightning flash with arrow A The exclamation point wkMn a
head within a triangle isintended _ triangle is intended to tell the
to tell the user that parts inside
the product are a risk of electdc
shock to persons
[] Note to CATV System mnstaEler: This reminder is provided to direct the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
[] Important Safety instructions for LCD TV
1) Read these instructions.
All the safety and operating instructions should be read before the appliance is operated,
2) Keep these instructions
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the appliance and in the operating instructions should be adhered to,
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
For example, near a bathtub, wash bowl kitchen sink. or laundry tub. in a wet basement, or near a
swimming pool, and the like.
6) Clean only with dry cloth
Do not use liquid cleaners or aerosol cleaners, Use a dry cloth for cleaning.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation of the
product and to protect it from overheating. The openings should never be blocked by placing the
product on a bed, sofa. rug, or other similar surface.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's instructions have been adhered to.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other, A grounding type plug has two blades and a third grounding prong, The
wide blade or the third prong are provided for your safety. Ifthe provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles.
and the point where they exit from the apparatus.
11) Only use attachments /accessories specified by the manufacturer.
12) Use only with the cart. stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart /
apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
This will prevent damage to the producl due to lightning and power-line surges.
14) Refer all servicing toqualified service personnel Servicing is requiredwhen the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid hasbeen spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected
2

important Safety instructions
18) If an outside antenna is connected to the EXA_,_PLEOFANTENNA
television equipment, be sure the antenna system GROUNDINGA£ PER(_'_EO)
is grounded so as to provide some protection
against voltage surges and built up static
charges In the US. Selection 810-21 of the
National Electrical Code provides information
with respect to proper grounding of the mast and
supporting structure grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
17) An outsideantenna system should not be located ELECTRODESYSTEM
in the vicinity of overhead power lines or other (NECART250,PARTH)
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an
outside antenna system extreme care should be taken to keep from touching such power lines or circuits
as contact with them might be fatal,
18)Unplug this LCD TV from the wall outlet, and refer servicing to qualified service personnel under the
following conditions:
a When the power cord or plug is damaged or frayed
b If liquid has been spilled into the LCD TV.
c If the LCD TV has been exposed to rain or water.
d, Ifthe LCD TV does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as improper adjustment of other
controls may result in damage and wB often require extensive work by a qualified technician to restore
the LCD TV to normal operation.
e If the LCD TV has been dropped or the cabinet has been damaged,
f. When the LCD TV exhibits a distinct change in performance - this indicates a need for service
19) When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards
20)WARNHG: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
DO NOT PLACE LIQUID CONTAINERS (FLOWER VASES, CUPS, COS[vIETIOS, ETC.} ABOVE THE
SET. (INCLUDING ON SHELVES ABOVE, ETC,)
21) CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG WITH A RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE,
! Hmpou'tanfrHnfm'maBm_Regarding Use of Video Games, Computm's, Capfriose m' Other Fixed HmageDispHays.
The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel,
This beckground image is viewable oR normal programs in the form of a stationary fixed image, This type of
irreversible LCD panel deterioration can be limited by observing the following steps:
A. Reduce tbe brightness /contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
! This product utilizse tiu_-lsedselbeu',and has a fllnm'seueu_tlamp eou_taiu_ingasmall amount of mercury. Disposal of
these materials may be rsgula_;d in your community due Nosnviromnsntal coseidemfrioue. Fro'disposal or reDycling
iu_fm'matim_please contact your flocaflauthm'itise, m' the EIsetrm_iueh_duetu'iseAflHiance:www.sise.org_
3

Dear Panasonie Customer
Welcome to the Pa_asol_ic family of eustomers_
We hope that you will have many years of enjoyment /?om your new LCD T_
To obtain maximum be_csfit from your set, please read these instructions before
mahi_g alzy adjustments, a_zd retai_ them S_r f_¢ture ref_renee_
Retain your purchase receipt, and record the model number and serial _umber
of your set in the space provided on the rear cover of these i_structions.
For assistance, please call : 1-800-211oPANA (7262)
o_ send e-mail to : consurnerproducts@panasonie,com
or visit us at www, panasonic,eom (U.S,A,)
For assistance, please call : 787°750°4300
or visit us at www.panasonie.eom (Puerto Rico)
For assistance, pmease call : 1o800-561o5505
or visit us at www.panasonic.ea (Canada)
Federal Communication Commission Information ]
This equipment has been tested and found to comply with the limits for a TV Broadcast Receiver, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause or receive interference, which can be determined by turning
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the TV antenna,
Increase the separation between TV and other equipment
Connect TV into separate outlet from other equipment
Consult the dealer or an experienced radio /TV technician for help.
FCC Caution: Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications not expressly
approved by Matsushita Electric Corporation of America could result in harmful interference and would void
the user's authority to operate this equipment,
The Energy Star label, a symbol for energy efficiency, was created by the US
Environmental Protection Agency (EPA) and the U.S. Department of Energy
(DOE) to help customers identify products that can save them money and protect
the environment by saving energy. Energy Star compliant products generally
consume less energy than similar standard products.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC,
HI@H-DEFUNITUON MULTIME_IA UNTERFACE
4

Important Safety h_structions .............................. 2
SUPPLIED ACCESSORIES ................................... 5
h_stallation ............................................................. 6
Corlrlectiorls .......................................................... 7
Antenna Connection ..................................... 7
Cable Box Connection ................................... 8
Connecting Other Equipment ..................... 9
Connecting Headphones/Earphones ............... 10
HDMI Connection 11
Basic Conlrols ..................................................... 12
Remote Control ................................................. 12
Main Unit 14
Power ON /OFF ...................................................14
ASPECT Controls ................................................ 15
Photo ViewerTM ....................................................16
Thumbnail Mode ........................................ 17
Photo Viewer TM Setup Menu 18
Menu Operations .................................................20
Tuning Channels ........................................... 22
LOCK .............................................. 24
CLOSED CAPTION .................................. 27
INPUT LABEL .................................... 28
OTHER ADJUST ....................................... 28
PICTURE ADJUST ..................................... 29
POSITION/SIZE 31
AUDIO ADJUST 32
Operating peripheral equipment using
the remote control ............................................ 33
Programming the remote control code ......... 33
Infrared Code Index 34
Mode Operational Key Chart 37
=Manual de instrucciones [ Resumen ]--
h_stalaci6n de las pHas
del mando a distancia ................................. 39
Conexion ........................................................40
Conexi6n de antena ........................... 40
Conexi6n del receptor de TV por cable .... 41
Controles basicos ......................................... 42
Control remoto iluminado ....................... 42
Aparato principal 44
Cone×i6n /desconexi6n de HaaHimeu_taci6n... 44
Photo Viewer TM .............................................. 45
Modo de imagen miniatura 45
Oper_oiones COrl133enus .............................. 46
SintonizaciSn de canales ...................... 48
SUPPUED ACCESSORIES
Check the accessories before installations,
® Operating instruction book ® Remote Control Transmitter ® Balteries for the Remote
(EUR7603ZG0) Control Transmitter
.... &_,_ (2 x AA size)
® Warranty Card ® Service Center List ® Customer Card ® F-Type Antenna ® Ferrite core
(For U,S.A.) (For U.S.A ) Connector
(for4O-2V) (x 1) (for HDMI cable) ( × 1)
5

SUPPLIED ACCESSORIES /installation
IF{emote controt battery installation
Requires two AA batteries=
1. Open the buttery cover. 2. Install the batteries
Notethecorrectpoladty(+and -), 3 Replace the cover.
Two AA size
z_ Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control
transmitter.
1. Always use new batteries when replacing the old set.
2. Do not altempt to charge, short-circuit, disassemble, heat or burn used batteries.
3. Battery replacement is necessary when remote control acts sporadically or fails to operate this unit.
Notes:
® Do not drop, apply shock to or step on the remote control
® Do not spill water on the remote control.
Do not place objects between the remote control and remote control receiver
® Do not use remote controls for other equipment at the same time
® If the TV does not operate even when using the remote control from a close range,
the batteries. it is time to replace
Receiver Location
Locatefor comfortableviewing Avoid phcing wheresunlightor other brightlight (induding reflections}will fall on the screen
Use of sometypes of fluorescentlightingcan reduceremotecontrol transmitterrange,
Adequateventilationis essentialto preventinternalcomponentfailure Keepawayfrom areasof excessiveheator moisture
Optional External Equipment
TheVideo/Audio connectionbetweencomponentscanbemadewith shieldedvideoandaudiocables Forbestperformance
antennacablesshouldutilize 75ohm coaxialshieldedwire.Cablesare availablefrom yourdealer or electronicsupplystore
Before you purchase any cables, be sure you know what type of output and input connectors your various
components require Also determine the length of cable you'll need,
For optimum quality picture
When the LCD is exposed to light from outdoors or lighting fixtures, high-contrast pictures may not be displayed
clearly Turn off florescent lamps near the LCD and place in a location not exposed to outdoor light,
How to hang the LeD TV on the wal
This LCD TV is for use only with the following optional accessory Use with any other type of optional
accessories may cause instability which could result in the possibility of injury
_, Wall-hanging bracket TY-WK32LX20W
Always be sure to ask a qualified technician to carry out set-up
How to use the LCD stand
Adjust the stand to your desired angle. The stand angle can be adjusted between 20 <left to 20 ' right,
6

Cover removal and fitting
Removal FBtth_g
1. Push down books and
pu,thecoversUgh,y ,-'_" /
iiiiiiiiiiiiiiii_ii_2_
_ _:_ towardsyourselfto
_Jdisengagetheclaws(at
\_" 4 points).
2. Slowly pull out in the
downward direction,
1 Insert the claws
(at 4 points) at
the bottom end.
2. Push it until
hook will be
cricked
Note:
Separate the RF cable and the power cord to avoid interference appearing on the screen.
Antenna Connection
For proper reception of VHF /UHF channels, an external antenna is required For best reception an outdoor
antenna is recommended. The antenna mode must be set to TV (see page 22. MODE)
VHF Antenna UHF Antenna
Mixer
Antenna
Terminal
75 Ohm Coaxial Cable
Back of the TV
9e Antenna Connector
mCabJe /Antenna Connection
F-TypeAntenna Connector
Antenna Terminal \
on the Back of the TV
Incoming 75 Ohm Cable from Home
Antenna /Cable Company
/
7

Cable Box Connection
, For reception of came channels (01 - 125), connect the cable supplied by your local came company.
The antenna mode must be set to CABLE (see page 22. MODE)
oCertaincablesystems offsetsomechannelsto reduceinterferenceor have Premium(scrambled)channels.A cable
converter boxis requiredfor properreception.Checkwith yourlocal cablecompany for itscompatibilityrequkements.
oSet the TV channel to CH3 or CH4. came when using this connection,
I Cable Box
Back of the TV
CABLE BOX
t
Cable Box and VCR
_ [nconflng 75 Ohm Cable
from Cable Company
Back of the TV
CABLE BOX
Incoming 75 Ohm Cable
from Cable Company
VCR
[D
8

Connecting Other Equipment
I Rear hput Terminals
Back of the TV
S-VIDEO cable -
t_' tt' t1" _1" Super-VHS VCR CAMCORDER V_DEO GAME
Notes:
* When connecting video cables priority is given to the S-Video cable when both the S-VIDEO input
terminal and the VIDEO input terminal are connecled
oPlease make inquiries to video game manufacturers concerning component cables to connect with
video game console.
9

Rear Output Terminals
AUDIO cable
I
Back of the TV
Front input Terminals
Front of the TV
AUDIO cable
VIDEO cable
S-WDEO cable
Audio
OUT
CAMCORDER
_de_
_J out
O SVu_O VIDEO GAME
CONSOLE
Connecting Headphones /Earphones
Front of the TV
(Not supplied)
10

HDMI Connection
HDMI _ (High Definition Multimedia Interface) is the first all digital consumer electronics AiV interface that
supports uncompressed standard The HDMI terminal supports both video and audio information
You can connect an EIA /0EA-861 /861B 2compliant consumer electronic device, such as a Set Top
Box or DVD player with HDMI or DVl output terminal to the HDMI `_input terminal,
Input a High-bandwidth Digital Content Protection (HDCP) high-definition picture source to this HDMI
terminal, so you can display high-definition pictures on this TV in the digital form,
Set Top Box
HDMI or DVI
signal out
DVD player
HDMI cable
Audio cable Ferrite core
(small size) (supplied)
Notes:
, If file external device has DVl output only, use a
DVl to HDMI adapter cable 3to connect to the
HDMI terminal
, Connect the audio cables to the AUDIO IN
terminals for HDMI.
, Select the audio setting in HDMI IN (see page 32)
Attaching the ferdte core
1 2
Pull back the tabs (in two Put the cable
places) to open. and close.
No. of dots (H x V) Vertical scanning frequency (Hz)
1080i 1,920 x 1,080i 59.94 /60
720p 1,280 x 720p 59.94 /60
480p 720 x 480p 59.94 /60
640 x 480p 59.94 /60
480i 720(1,440) x 480i 5994 /60
This input terminal is not intended for use with corn _uters.
[] Compatible sampling frequency of AUDIO siglal (L.PCM} : 48 kNz /44.1 kNz /32 kNz
Notes:
, This HDMI connector is Type A.
, If you connect an equipment without a digital output terminal, connect to the COMPONENT VIDEO. S
VIDEO or VIDEO input terminal on the TV so you can enjoy an analog signal.
'_1, HDMI, the HDM! logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
'_2, EIA /CEA-861 /861B profiles compliance covers profiles for transmission of uncompressed digital
video including high bandwidth digital content protection.
>:_3.HDMI-DVl conversion cable (TYLSCHO3DH): available on Panasonic website (www.panasonic.com).
Consult your consumer electronics dealer for availability details.
11

Remote Control
POWER button
Press to turn the TV on or off (see page 14).
Note:
This does not work when the main power is off
(No light),
MUTE button
Press to mute the sound.
Press again to cancel mute
Mute is canceled when the power
volume level is changed is turned off or
Mode Selection buttons
(see page 33)
MENU button
(see page 20)
RECALL button
Press to display channel number, sleep
timer and other options,
R-TUNE button
Press to switch to previously viewed channel or to switch
between TV mode and another input mode.
SD button
Press to access Photo Viewer TM (see page 17}
Operation of other devices
(see pages 37, 38)
\/
12

Basic Controls
ASPECT button (see page 15)
-- TV/VIDEO button
Press to change the input mode.
SAP button
Press to select the audio mode. You can
also change the mode in the MENU screen
(see page 32).
I -]
_ STEREO--_ SAP --_ MONO
LIGHT button
Press to light the remote
control buttons.
The selected button blinks
when lit,
RETURN button
Return to previous MENU (TV mode).
EXiT button
GUIDE button (DBS mode)
PAGE button
Page up /down (DBS mode).
Skip + /-(DVD & CD mode)
Numbered buttons
Reduces volu[f_e --
Moves cursor to
the left during
menu mode.
Channel up
Moves cursor upward during menu mode
Choose menu and
submenu entry.
Moves cursor to
the right during
menu mode,
Channel dowrl
Movescursordownwardduring menumode.
-- SLEEP button (TV mode)
Set the sleep time to put the TV into standby mode
F 0 =----=_30 _ 60 =-------_90 -7
oWhen 3 minutes left, <'[] 3 "will flash ("2" for 2 minutes and "1" for
1 minute)
oThe SLEEP timer is cancelled when the power is turned off.
PROG = button (DBS or DTV mode)
When tuning digital channel, press the button to enter the minor
number in a compound channel number.
oTo enter the channel number
ex. CH 15-1: [1]i'_[5] i'_ [-]i_[1]i_[OK]
13

Basic Controls /Power ON /OFF
Main Unit
Power Undicator
Power on : Green
Power off : No Liqht
Power off (Standby): Red
SD CARD slot PC CARD slot Volume Up /Down
Main POWER swUtch Remote control sensor
Press to turn the TV's Within about 20 feet
main power on /off /6 meters) in front of the
(see below) TV set
EJECT button Cham_el Up /Down
Preparation outs ° [] _ [_
Connect the plug to the wall . o_] o
Notes:
oThe TV consumes some power as long as the power cord is inserted into the wall outlet,
oDo not remove or slide the ferrite core for the safety purpose.
On the main unit
Main POWER
switch
Press to turn the TV's main power on /off,
oPower indicator
Main power ON: Green
Main power OFF: No light
On the remote control
Remote control sensor
Power Indicator Press to turn the TV on /off.
,Power indicator
Power ON: Green
Power OFF (Standby): Red
• This does not work when the main
power is off (No light) (see above)
Note:
o The screen below is displayed for a few
moments when the TV is turned on
ZOOM
Note:
,Select the menu language before operating the TV
(see page 21, LANGUAGE),
14

This feature allows you to enjoy viewing the picture at its maximum size. including wide screen cinema
format picture.
ASPECT Each time you press the button:
0
Notes:
oThis feature does not work for 1080i and 720p input signals,
oThis feature does not work during Photo Viewer TMthumbnail
mode or single picture view mode.
oThe aspect setting is stored separately for TV. VIDE01. VIDE02,
COMPONENT1, COMPONENT2. HDMI and Photo Viewer _M
Slide Show (see page 18),
I_ 4 _1
0 0
I-- 4--I
}-- 4 _1
O(--',_jO I '4'
0 _J 0
X-J
NORMAL mode will display a 4:3
>icture at its standard 4:3 size without
any stretching,
JUST mode will display a 4:3 picture
at its maximum size but with aspect
correction applied to the sides of the
screen so that elongation is only
apparent at the left and right edges of
the screen The size of the picture will
depend on the original signal.
ZOOM mode magnifies the central
section of the picture.
FULL will display the picture at its
maximum size but with slight
elongation.
15

PhotoViewer_Mlets you display JPEG images recorded by digital still camera on SD card or other types
of memory card when it is inserted in the proper card slot.
I Compatible card type and card size I Folders and Fi_es
1
SD card slot |
® SD Card {512MB) ® MultiMediaCard(128MB
1
PCMCIA card slot
® SD Card (512MB) ® miniSD Card (128MB)
® MultiMediaCard(128MB}o Compact Flash (1GB)
® Smart Media (128MB) o Memory Stick {128MB)
® xD PictureCard(128MB)® FlashATA(128 MB)
The cards require standard PCMCIA card
adapter. (Some PC card adapter will not be
compatible)
miniSD Card requires miniSD adapter.
,Photo Viewer TMis not compatible with card type
hard disk (Micro Drive, Mobile type hard disk, etc).
,Memory cards are not supplied with this
television.
,When both SD card and PCMCIA card are
inserted in the slot, SD card has the priority.
[] Card Data Protection
,Do not remove the card while Photo Viewer T_4is
accessing the information (when the card icon
is flashing) Such action may damage the
memory card or the unit itself
,Before inserting or removing the PCMCIA card.
make sure that the TV is turned Off Otherwise,
it may damage the unit.
,Do not touch the terminals on the back of the
SD card /PCMCIA card
,Always insert a card in the correct direction,
Failure to do so may result in damage to the
card and this unit
,Do not subject the card to excessive pressure or
strong impacts
,Electrical interference, electrostatic discharges
and malfunctions of the unit or card may all
result in data loss or damage to the card,
,Stored data should be periodically backed up as
a protection against data corruption, data loss
or device malfunction. Please note that
Panasonic shall not accept any liability for
damage or loss of stored data.
, WARNING: As with any srnal obiect, an SD
card can be swallowed by young chtdren.
Do not allow chiMren to handle SD card.
Please remove SD card immediately after use.
,Photo Viewer _Mcan only show still images
recorded by a digital still camera with DCF' and
EXlF standard JPEG file.
DCF (Design rule for Camera File system)
Unified standard established by Japan
Electronics and Information Technology
Industries Association (JEITA)
,Memory cards must be formatted with FAT12 or
FAT16 in order to be viewed on TV. If the card
is not formatted, it may cause incompatibility
with certain memory card adapters. If this
happens, reformat the card using your digital
still camera. Reformatting the card will erase
the images stored in it. Refer to your camera
manual for more information.
,Maximum number of folders that can be
displayed: 100,
,Maximumnumber of files that can be displayed: 3000
,Picture resolution: Compatible in the range 64
x 64 - 8192 x 8192 (sub-sampling 4:2:2 or 4:2:0)
,If the image is imported from a PC. it must
follow the EX_F (Exchangeable Image File
Format) 2.0, 2.1.2.2 in addition to the DCF
format.
,The JPEG modified using a PC will not be
displayed on TV.
,The Photo Viewer TMcannot display Motion
JPEG and still image not DCF formatted (i.e.
TIFR BMP).
,If the file is partially corrupted it may be shown
in lower resolution
,The displayed image size depends on the
recorded size.
Example folder structure
JPEG images in all the folders are displayed
sequentially
Created automatically
I 100 PANA-- Folde_ name_ conr,ist of
I
I
I
i _101 f_ANA
i
Note:
,Folder and file names may vary according
to the digital still camera.
,Use the characters "a-z", "A-Z", "0-9" and
to name a directory or a file Do not use
two-byte characters or other special codes,
16

Photo Viewer TM
Inserting and removing a card
[] SD card sJot
hsert the card Remove the card
Lower
[] PCMCIA card slot
Turn the TV off before inserqng or removing a PCMCIAcard.
Insert the card Remove the card
1. Push the center upward
2. Insert it unit it of the card.
clicks in.
Push the
eject button
Jfthe eject buttol_ does not pop out
Push in PCMCIA card again, and
then push again the eject button
Note:
If PCMCIA card adapter is used,
remove it logether with the
adapter.
Thumbnail Mode
The thumbnail screen is the initial entry screen from the main menu.
oWhen both SD card and PCMCIA card are inserted, the TV plays SD card To play a PCMCIA card_
sebct "PC" in "Card" (see page 19) after inserting the PCMCIA card
1Insert the card into the appropriate slot (see above).
OR
pLAy Press to display the thumbnail screen.
Picture No. /Total No of pictures
File name, the date and the pixel (resolution
of the picture
RECA_ pAGE _UI_E
OQG) O
@ ® ®
® ®®
®® ®
REW FF
_us_ nEe
_'Oa VeReH r)Ra'ICLC_I
Q _ Q _
Note:
,It may take long time to display the thumbnail if there are Iotaof flies or the file size is large,
,The video disappears from the screen while the Photo Viewer TMaccess the
information from the card. After accessing the images from the card, a thumbnail
screen is displayed.
Select the thumbnail
image,
Single picture view mode
Press to display the
image in the single picture
view mode,
3-- Press to select the next or the previous picture.
,Press OK to return to the thumbnail screen.
To rotate the picture
While in the single picture view mode Press to rotate the
picture ninety degree.
17

Photo Viewer TM
Photo Viewer TM Setup Menu
This menu allows you to customize features in the Photo Viewer TMSetup Menu
While h_the thumbnail mode or the single pBcture vBew n_ode {see page 17)
1PLAY Press to display the Setup Menu
screen,
2
menu,
Slide Show
Select the settings of Interval, Sequence and Repeat before starting the slide show.
__ Press to select the sub-menu,
Press to adjust or activate the sub-menu.
[] hterval
Allows you to change the length of time that a slide is being displayed on
screen, (5Sec, 10Sec, 15Sec, 30Sec, 60Sec, 90Sec, lOMin).
[] Sequence (Order or Random}
[] Repeat (OFF or ON}
_/_..iiii Press to select Start,
Press to start the slide show,
I(_(_ 0/_,_!_ Press again to stop.
_______j Press ASPECT to change the aspect of the image (see page 15),
Rotate
(While h_the sUngle picture mew mode only)
Allows you to rotate the image (see also page 17).
_ Press to select Rotate.
Press to select Left or Right.
Press to activate the setting,
18

Photo Viewer TM
Zoom
(While in the single picture view mode only}
Lets you select the magnification of the single picture display.
1 Press toselect Zoom,
Press to select To Fit, x2 or x4.
t _'---_ Press to activate the setting.
2Press to move the image in the picture frame.
To cancel Zoom
Press OK to view the picture in normal magnification.
Card
Select either SD or PC when both cards are inserted in the slots.
Press to select Card.
Press to select SD or PC.
Photo Viewer TM Troubleshooting
Symptom Cause and remedy
oNot compatible format. Must be formatted with FAT 12 or FAT
16.
Cam_ot read the content of the card. oThe extension is not "JPGL
oThe folders not under DCF standard.
PC card cannot be ejected. Push the card all the way in, and eject.
Ifthe main image cannot be read (the file is partially corrupted),
Poor picture quality, the Photo viewer ]M will read the thumbnail. Please confirm the
format of the image.
Picture takes a long time to display. There are lots of images or the file size is large.
"Card is not inserted correctly=" Insert a card.
"This type of image is net supported=" The JPEG file iscorrupted and cannot be decoded,
"This type of format isnot supported." The card is not formatted with FAT 12 or FAT 16 or
if it is not DCF standard.
" _" Thumbnail and main picture cannot be shown.
"Photo Viewercannot support over 3000JPEG flies." Over 3000 image files.
"Photo Viewerca_motsupport over 8192x 8192pixeIs." Resolution over,
"This _,pe of card ie not sappmled." Incompatible card is inserted,
19

I
20
IPress to display MENU
screen
AUDIO ADJUST
I
SAP
PAGE GUIDE
ON SCREEN HELP qDStrUctJOW box
An On Screen Help box is displayed when a menu is displayed
on the TV. This Help box indicates which keys on the remote control
are used to navigate the menu shown.
LANGUAGE
I
or
LOCK
CLOSED CAPTION
INPUT LABEL
OTHER ADJUST
LOCK
_=:_INPUT LABEL
OTHER ADJUST