Panasonic TX-PR42U10 User manual

ORDER NO.PCZ0907119CE
Plasma Television
Model No. TX-PR42U10
GPF12DE C assis
A WARNING
This service information is desi ned for experienced repair technicians only and is not desi ned for use by the eneral public.
It does not contain warnin s or cautions to advise non-technical individuals of potential dan ers in attemptin to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by A in the Schematic
Dia rams, Circuit Board Dia rams, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced
with manufacturer's specified parts to prevent shock, fire or other hazards. Do not modify the ori inal desi n without permission of
manufacturer.
Panasonic' © Panasonic Corporation 2009.
Unauthorized copyin and distribution is a violation
of law.
All manuals and user guides at all-guides.com
all-guides.com

TABLE OF CONTENTS
1 Safety Precautions------------------------------------------------
1.1. General Guidelines ----------------------------------------
1.2. Touch-Current Check--------------------------------------
2 Warning-----------------------------------------------------------------
2.1. Prevention of Electrostatic Dischar e (ESD)
to Electrostatically Sensitive (ES) Devices ------
2.2. About lead free solder (PbF) --------------------------
3 Service Navigation -------------------------------------------------
3.1. Service Hint---------------------------------------------------
PAGE
------- 3
------- 3
------- 3
------ 4
3.2. Applicable si nals --------------------
4 Specifications ----------------------------------
5 Service Mode -----------------------------------
5.1. How to enter into Service Mode -
5.2. Service tool mode---------------------
5.3. Hotel mode-------------------------------
6 Troubles ooting Guide ---------------------
6.1. Check of the IIC bus lines ----------
6.2. Power LED Blinkin timin chart -
6.3. No Power ----------------------------------
6.4. No Picture ----------------------------------------
6.5. Local screen failure --------------------------
7 Service Fixture & Tools----------------------------
7.1. SC ji -----------------------------------------------
8 Disassembly and Assembly Instructions -
8.1. Remove the Rear cover--------------------
8.2. Remove the P-Board--------------------------------------
8.3. Remove the Side terminal cover and Rear
terminal cover------------------------------------------------
8.4. Remove the Tuner unit ■
8.5. Remove the A-Board —
8.6. Remove the Speakers -
8.7. Remove the Control button unit
8.8. Remove the GK-Board ------------
8.9. Remove the SU-Board--------------
10. Remove the SD-Board--------------
11. Remove the SC-Board--------------
12. Remove the SS2-Board -----------
13. Remove the SS-Board--------------
8.21. Replace the plasma panel —
9 Measurements and Adjustments
9.1. Adjustment Procedure ---------
9.2. Adjustment --------------------------
10 Block Diagram----------------------------
10.1. Main Block Dia ram ------------
10.2. Block (1/4) Dia ram ------------
10.3. Block (2/4) Dia ram ------------
10.4. Block (3/4) Dia ram ------------
10.5. Block (4/4) Dia ram ------------
11 Wiring Connection Diagram --------
-- 4
-- 5
-- 6
-- 6
-- 7
-- 8
-- 9
-- 9
11
12
13
13
14
15
16
17
18
18
19
19
19
14. Remove the Han er metals and the Stand
brackets---------------------------------------------------------
8.15. Remove the C1-Board -----------------------------------
8.16. Remove the C2-Board -----------------------------------
8.17. Remove the Plasma panel section from the
Cabinet assy ( lass)---------------------------------------
8.18. Remove the S-Board--------------------------------------
8.19. Remove the Front lass ---------------------------------
8.20. Remove the K-Board--------------------------------------
19
-20
20
-21
21
-21
-21
-22
-22
22
-23
23
-23
-23
24
24
25
25
25
- 26
-26
29
- 33
33
34
35
36
37
- 39
11.1. Caution statement.
11.2. Wirin (1) -------------
11.3. Wirin (2 )-------------
11.4. Wirin (3 )-------------
12 Sc ematic Diagram --------------------------------------
12.1. Schematic Dia ram Note----------------------
12.2. P-Board (1/2) Schematic Dia ram --------
12.3. P-Board (2/2) Schematic Dia ram --------
12.4. GK, K and S-Board Schematic Dia ram-
12.5. A-Board (1/20) Schematic Dia ram -------
12.6. A-Board (2/20) Schematic Dia ram -------
12.7. A-Board (3/20) Schematic Dia ram -------
12.8. A-Board (4/20) Schematic Dia ram -------
12.9. A-Board (5/20) Schematic Dia ram ------
12.10. A-Board (6/20) Schematic Dia ram -------
12.11. A-Board (7/20) Schematic Dia ram -------
12.12. A-Board (8/20) Schematic Dia ram -------
12.13. A-Board (9/20) Schematic Dia ram -------
12.14. A-Board (10/20) Schematic Dia ram-
12.15. A-Board (11/20) Schematic Dia ram-
12.16. A-Board (12/20) Schematic Dia ram-
12.17. A-Board (13/20) Schematic Dia ram-
12.18. A-Board (14/20) Schematic Dia ram-
12.19. A-Board (15/20) Schematic Dia ram-
12.20. A-Board (16/20) Schematic Dia ram-
12.21. A-Board (17/20) Schematic Dia ram-
12.22. A-Board (18/20) Schematic Dia ram-
12.23. A-Board (19/20) Schematic Dia ram-
12.24. A-Board (20/20) Schematic Dia ram-
12.25. C1-Board (1/2) Schematic Dia ram -
12.26. C1-Board (2/2) Schematic Dia ram -
12.27. C2-Board (1/2) Schematic Dia ram -
12.28. C2-Board (2/2) Schematic Dia ram -
12.29. SC-Board (1/4) Schematic Dia ram -
12.30. SC-Board (2/4) Schematic Dia ram -
12.31. SC-Board (3/4) Schematic Dia ram -
12.32. SC-Board (4/4) Schematic Dia ram -
12.33. SS-Board (1/2) Schematic Dia ram --
PAGE
---- 39
---- 39
---- 40
---- 41
---- 43
---- 43
---- 44
---- 45
---- 46
---- 47
---- 48
---- 49
---- 50
---- 51
---- 52
---- 53
---- 54
---- 55
---- 56
---- 57
---- 58
---- 59
---- 60
---- 61
---- 62
---- 63
---- 64
---- 65
---- 66
---- 67
---- 68
---- 69
---- 70
---- 71
---- 72
---- 73
---- 74
---- 75
12.34. SS-Board (2/2) and SS2-Board Schematic
Dia ram ----------------------------------------------------------- 76
13 Printed Circuit Board----------------------------------------------- 77
13.1. P-Board------------------------------------------------------------77
13.2. GK, K, S and SS2-Board ----------------------------------- 80
13.3. A-Board ------------------------------------------------------------ 81
13.4. C1-Board-----------------------------------------------------------83
13.5. C2-Board-----------------------------------------------------------84
13.6. SC-Board----------------------------------------------------------85
13.7. SS-Board----------------------------------------------------------88
14 Exploded View and Replacement Parts List ------------ 91
14.1. Exploded View and Mechanical Replacement
Parts List---------------------------------------------------------- 91
14.2. Electrical Replacement Parts List-----------------------98
2
All manuals and user guides at all-guides.com

1 Safety Precautions
1.1. General Guidelines
1. When servicin , observe the ori inal lead dress. If a short circuit is found, replace all parts which have been overheated or
dama ed by the short circuit.
2. After servicin , see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicin , make the followin leaka e current checks to prevent the customer from bein exposed to shock hazards.
4. When servicin , observe the ori inal lead dress. If a short circuit is found, replace all parts which have been overheated or
dama ed by the short circuit.
5. After servicin , see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
6. After servicin , make the followin leaka e current checks to prevent the customer from bein exposed to shock hazards.
1.2. Touc -Current C eck
1. Plu the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measurin network for touch currents between each exposed metallic part on the set and a ood earth round
such as a water pipe, as shown in Fi ure 1.
3. Use Leaka e Current Tester (Simpson 228 or equivalent) to measure the potential across the measurin network.
4. Check each exposed metallic part, and measure the volta e at each point.
5. Reserve the AC plu in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUGH CURRENT) expressed as volta e U1 and U2, does not exceed the followin values:
For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak);
For d. c.: U1 = 1.0 V,
Note:
The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
mA d. c.
The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies reater than 100 kHz.
7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.
Measuring network for TOUCH CURRENTS
COLD
WATER PIPE
(EARTH GROUND)
Rs=
1500Q_ L Cs= 0.22|jF
10kQ
-1 k 1
------- 1
Ro=
----------------
J 500Q 'U1 =
r
= 0.022|jF (V)
JQ LjJ JUUii U1 —|— и.и^гфГ ^ V J | U2 (V)
APPLIANCES
EXPOSED
METAL PARTS
Resistance values in ohms (Q)
V: Voltmeter or oscilloscope
(r.m.s. or peak readin )
Input resistance: > 1 MQ
Input capacitance: < 200 pF
Frequency ran e: 15 Hz to 1 MHz and d.c. respectively
NOTE - Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms.
Fi ure 1
3
All manuals and user guides at all-guides.com

2 Warning
2.1. Prevention of Electrostatic Disc arge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be dama ed easily by static electricity. Such components commonly are called Elec
trostatically Sensitive (ES) Devices. Examples of typical ES devices are inte rated circuits and some field-effect transistors and
semiconductor [chip] components. The followin techniques should be used to help reduce the incidence of component dama e
caused by electrostatic dischar e (ESD).
1. Immediately before handlin any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touchin a known earth round. Alternatively, obtain and wear a commercially available dischar in ESD wrist strap,
which should be removed for potential shock reasons prior to applyin power to the unit under test.
2. After removin an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi
num foil, to prevent electrostatic char e buildup or exposure of the assembly.
3. Use only a rounded-tip solderin iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
enerate electrical char e sufficient to dama e ES devices.
5. Do not use freon-propelled chemicals. These can enerate electrical char es sufficient to dama e ES devices.
6. Do not remove a replacement ES device from its protective packa e until immediately before you are ready to install it. (Most
replacement ES devices are packa ed with leads electrically shorted to ether by conductive foam, aluminum foil or compara
ble conductive material).
7. Immediately before removin the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handlin unpacka ed replacement ES devices. (Otherwise ham less motion such as the brush
in to ether of your clothes fabric or the liftin of your foot from a carpeted floor can enerate static electricity (ESD) sufficient
to dama e an ES device).
4
All manuals and user guides at all-guides.com

Note: Lead is listed as (Pb) in t e periodic table of elements.
In t e information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
T e Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
T at is Tin (Sn), Silver (Ag) and Copper (Cu) alt oug ot er types are available.
This model uses Pb Free solder in it's manufacture due to environmental conservation issues. For service and repair work, we'd
su est the use of Pb free solder as well, althou h Pb solder may be used.
PCBs manufactured usin lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
• Pb free solder has a hi her meltin point than standard solder. Typically the meltin point is 50 ~ 70 °F (30~40 °C) hi her. Please
use a hi h temperature solderin iron and set it to 700 ± 20 °F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too hi h (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applyin Pb sol
der. If this is not practical, be sure to heat the Pb free solder until it melts, before applyin Pb solder.
• After applyin PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see fi ure below)
component component
remove all of the ^1П\
excess solder
2.2. About lead free solder (PbF)
slice
\
solder
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+A +Cu (tin, silver, copper) solder. How
ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
5
All manuals and user guides at all-guides.com

3 Service Navigation
3.1. Service Hint
Board Name Function
P Power Supply
A DC-DC Converter, Tuner
Speaker out, AV Terminal, AV Switch,
Di ital Si nal Processor, SYSTEM MPU, HDMI Switch
Peaks-AVC, Ethernet
Format Converter, Plasma AI, Sub-Field Processor
K Remote receiver, Power LED
S Power Switch
GK Key Switch
Board Name Function
C1 Data Driver (Lower Ri ht)
C2 Data Driver (Lower Left)
SC Scan Drive
SS Sustain Drive
SS2 Sustain out (Lower)
SU Scan out (Upper)
Non-serviceable.
SU-Board should be exchan ed for service.
SD Scan out (Lower)
Non-serviceable.
SD-Board should be exchan ed for service.
6
All manuals and user guides at all-guides.com
all-guides.com

3.2. Applicable signals
COMPONENT (Y, PB, PR), HDMI
* Mark: Applicable input si nal for Component (Y, PB, PR) and HDMI
Si nal name COMPONENT HDMI
525 (480) / 60i * *
525 (480) / 60p * *
625 (576) / 50i * *
625 (576) / 50p * *
750 (720) / 60p * *
750 (720) / 50p * *
1,125 (1,080) / 60i * *
1,125 (1,080) / 50i * *
1,125 (1,080) / 60p *
1,125 (1,080) / 50p *
1,125 (1,080) / 24p *
PC (from HDMI terminal)
Applicable input si nal for PC is basically compatible to HDMI standard timin .
Si nal name Horizontal frequency (kHz) Vertical frequency (Hz)
640 x 480 @60 Hz 31.47 60.00
750 (720) / 60p 45.00 60.00
1,125 (1,080) / 60p 67.50 60.00
Note
• Si nals other than above may not be displayed properly.
• The above si nals are reformatted for optimal viewin on your display.
• PC si nal is ma nified or compressed for display, so that it may not be possible to show fine detail with sufficient clarity.
7
All manuals and user guides at all-guides.com

4 Specifications
Power Source
Power Consumption
Power Consumption in Standby condition
Display panel
Aspect Ratio
Visible screen size
Number of pixels
Sound Speaker
Audio Output
Headp ones
Receiving Systems / Band name
Aerial - Rear
Operating Conditions
Connection Terminals
AV1 (Scart terminal)
AV2 (Scart terminal)
AV3 VIDEO
S-VIDEO
AUDIO L - R
COMPONENT
VIDEO
AUDIO L - R
Ot ers
HDMI1 / 2
Card slot
Output
AUDIO L - R
DIGITAL AUDIO OUT
Dimensions (W x H x D)
Mass
Note
AC 220-240 V, 50 / 60 Hz
350 W
0.4 W
16:9
106 cm (dia onal) 921 mm (W) x 518 mm (H)
2,073,600 (1,920 (W) x 1,080 (H)) [5,760 x 1,080 dots]
160 mm x 40 mm x 2 pcs, 6 Q
20 W (10 W + 10 W), 10 % THD
M3 (3.5 mm) stereo mini Jack x 1
PAL B, G, H, I, SECAM B, G, SECAM L, L’
VHF E2 - E12
VHF A - H (ITALY)
UHF E21 - E69
CATV S1 - S10 (M1 - M10)
CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2
VHF R6 - R12
PAL 525/60
M.NTSC
NTSC (AV input only)
• TV si nals may not be received in some areas.
VH F / UHF
VHF H1 - H2 (ITALY)
CATV (S01 - S05)
CATV S11 - S20 (U1 - U10)
VHF R3 - R5
UHF E21 - E69
Playback of NTSC tape from some PAL Video recorders (VCR)
Playback from M. NTSC Video recorders (VCR)
Playback from NTSC Video recorders (VCR)
Temperature:
Humidity: 0 °C - 35 °C 20 % - 80 % RH (non-condensin )
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
RCA PIN Type x 1
Mini DIN 4-pin
RCA PIN Type x 2
Y
Pb, Pr
RCA PIN Type x 2
1.0 V [p-p] (75 Q)
Y:1.0 V [p-p] (75 Q) C:0.286 V [p-p] (75 Q)
0.5 V [rms]
1.0 V [p-p] (includin synchronization)
± 0.35 V [p-p]
0.5 V [rms]
TYPE A Connectors HDMI™ (Version 1.3a with x.v.Colour™)
• This TV supports [HDAVI Control 4] function.
SD Card slot x 1
RCA PIN Type x 2 0.5 V [rms] (hi h impedance)
PCM / Dolby Di ital, Fiber optic
1.029 mm x 704 mm x 334 mm (With Pedestal)
1.029 mm x 661 mm x 100 mm (TV only)
27.0 k Net (With Pedestal)
25.0 k Net (TV only)
Desi n and Specifications are subject to chan e without notice. Mass and Dimensions shown are approximate.
8
All manuals and user guides at all-guides.com

5 Service Mode
5.1. How to enter into Service Mode
While pressin [VOLUME ( - )] button of the main unit, press [0] button of the remote control three times within 2 seconds.
Software version ■
Picture adjustment ----------
White balance adjustment
Option settin -----------------
A i -------------------------------
Service tool
SERVICE
ADJUST
WB-ADJ
OPTION
AGING
SRV-TOOL
1
Peaks SOFT *.*** OPTION 1 1c
Peaks EEP OPTION 2 ef
LSI DATA OPTION 3 01
STBY SOFT Model ID 05
STBY EEP 02203100
STBY ROMCOR 00000040
PDP SOFT RB Cn+ 000
PDP EEP
PDP FPGA
PDP PDROM
Press
[1]
Button
I Sub Item
1 1
Ia d ju s t" i '
'CONTRAST i '0000i
YMAX
5.1.1. Key command
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[RED] button...All Sub items Selection in forward direction
[GREEN] button...All Sub items Selection in reverse direction
[VOL] button...Value of sub items chan e in forward direction ( + in reverse direction ( - )
9
All manuals and user guides at all-guides.com

5.1.2. Contents of adjustment mode
• Value is shown as a hexadecimal number.
• Preset value differs dependin on models.
• After enterin the adjustment mode, take note of the value in each item before startin adjustment.
Main item Sub item Sample data Remark
ADJUST CONTRAST 000
COLOR 2B
TINT 00
SUB-BRT 80С
H-POS 0
H-AMP 0
V-POS 0
V-AMP 0
WB-ADJ R-CUT 80
G-CUT 80
B-CUT 80
R-DRV DD
G-DRV FC
B-DRV D5
ALL-CUT 80
ALL-DRV FC
OPTION Panel-Type 42FHD Factory
Boot ROM Preset
STBY-SET 00
EMERGENCY ON
Y/С Delay
OPT 1 00011100
OPT 2 11101111
OPT3 00000001
AGING RGBW
Vertical line
All white (COUNTER)
All white
All red
All reen
All blue
ON/OFF
Dia onal lamp W
Dia onal lamp R
Dia onal lamp G
Dia onal lamp В
1% WINDOW
COLOR BAR
A В zone/checkerd 4 trio
SCROLL BAR
2dot width border
Low setup red
Low setup reen
Low setup blue
SRV-TOOL see next
Destinations TX-PR**U10
Russia
Checksum 6741
EDID e2 2b1b—-
5.1.3. How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
10
All manuals and user guides at all-guides.com

5.2. Service tool mode
5.2.1. How to access
1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.
Display of TD2Microcode version —
Display of Flash ROM maker code -
Display of SOS History ----------------
SRV-TOOL
TD2Microcode:00500985
Flash ROM : 1 - 227E
PTCT : 00 . 00 . 00 . 00 . 00 Time 00000:40 On/Off 0000022 . POWER ON Time, On/Off
Press [MUTE] button (3sec)
5.2.2. Display of SOS History
SOS History (Number of LED blinkin ) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1 st occurrence after shipment.
This indication will be cleared by [Self-check indication and forced to factory shipment settin ].
5.2.3. POWER ON Time, On/Off
Note : To display Time, On/Off menu, hi hli ht position, then press MUTE for 3sec.
Time : Cumulative power on time, indicated hour : minute by decimal
On/Off : Number of On/Off switchin by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
5.2.4. Exit
1. Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.
11
All manuals and user guides at all-guides.com
all-guides.com

5.3. Hotel mode
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu
In order to display the Hotel mode setup menu, please
enter the followin command (wit in 2 second).
[TV] : Vol. [Down] + [REMOTE] : AV (3 times)
Then, the Hotel mode setup menu is displayed.
Hotel Mode
Hotel Mode 1 Off
_______________________ |
Initial INPUT 1 Off 1
Intial POS 1 Off 1
Intial VOL Level Гот |
Maximum Vol Level 1 63 |
Button Lock Гот |
Remote Lock ГШ |
Select
^o E X IT
иой- Chan e
~ °RETURN
3. To exit the Hotel mode setup menu
Disconnect AC power cord from wall outlet.
4. Explain the Hotel mode setup menu
item Function
Hotel Mode Select hotel mode ON/OFF
Initial INPUT Select input si nal modes.
Set the input, when each time power is switched
on.
Selection :
Off/TV/AV1/AV2/AV2S/AV3/AV3S/COMPONENT/
HDMI1/HDMI2
• Off: ive priority to a last memory. However,
Euro model is compulsorily set to TV.
• AVnS/AVnC: only Euro model selectable
• PC: selectable with VGA option
Initial POS Select pro ramme number.
Selection :
Off/0 to 99
• Off: ive priority to a last memory
Initial VOL level Adjust the volume when each time power is
switched on.
Selection/Ran e :
Off/0 to 63
• Off: ive priority to a last memory
Maximum VOL
level Adjust maximum volume. Ran e :
0 to 63
Button lock Select local key conditions.
Selection :
Off/SETUP/MENU/ALL
• Off: alto ether valid
• SETUP: only F-key is invalid
(Tunin uide(menu) can not be selected.)
• MENU: only F-key is invalid
(only Volume/Mute can be selected.)
• ALL: alto ether invalid.
Remote lock Select remote control key conditions.
Selection :
Off/SETUP/MENU
• Off: alto ether valid
• SETUP: only Setup menu is invalid
• MENU: Picture/Sound/Setup menu are invalid
12
All manuals and user guides at all-guides.com

6 Troubles ooting Guide
Use the self-check function to test the unit.
1. Checkin the IIC bus lines
2. Power LED Blinkin timin
6.1. C eck of t e IIC bus lines
6.1.1. How to access
Self-check indication only:
Produce TV reception screen, and while pressin [VOLUME ( - )] button on the main unit, press [OK] button on the remote control
for more than 3 seconds.
Self-check indication and forced to factory shipment settin :
Produce TV reception screen, and while pressin [VOLUME ( - )] button on the main unit, press [MENU] button on the remote con
trol for more than 3 seconds.
6.1.2. Screen display
6.1.3. C eck Point
Confirm the followin parts if NG was displayed.
Display Ref. No. Description P.C.B.
ADV IC4510 AD/HDMI A-Board
ADAV IC2106 Sound Processor A-Board
TUN TU8301 Tuner A-Board
GENX IC1100 GenX (STB MCU) A-Board
MEM1 IC1101 EEPROM (GenX) A-Board
MEM2 IC8502 EEPROM (Peaks) A-Board
AVSW IC3001 Audio/Video SW A-Board
PDP-PANEL IC9003 MICOM A-Board
TEMP IC4800 Temp Sensor A-Board
VIF TU8301 Tuner A-Board
6.1.4. Exit
Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.
13
All manuals and user guides at all-guides.com

6.2. Power LED Blinking timing c art
1. Subject
Information of LED Flashin timin chart.
2. Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
14
All manuals and user guides at all-guides.com

6.3. No Power
First check point
There are followin 2 states of No Power indication by power LED.
1. No lit
2. Red is lit then turns red blinkin a few seconds later. (See 6.2.)
15
All manuals and user guides at all-guides.com

6.4. No Picture
No Picture
Check NG
16
All manuals and user guides at all-guides.com
all-guides.com

6.5. Local screen failure
Plasma display may have local area failure on the screen. Fi -1 is the possible defect P.C.B. for each local area.
Fi -1
17
All manuals and user guides at all-guides.com

7 Service Fixture & Tools
7.1. SC jig
Purpose:
To find the failure board (SC or SU/SD) when the power LED is blinkin 7 times.
SC jig:
Jumper connector to connect to SC50 connector on SC board
Part number:
TZSC09187
How to use:
Caution: Remove SC jig from SC board after inspection.
1. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.
Note: The board will be dama ed if all connector is not removed (for example; remove connector only for SU board and stay
connectin with SD board. The board will be dama ed.)
2. Connect SC ji to connector SC50 at left bottom side of SC board
3. Turn of the TV/Display Unit and confirm the power LED blinkin .
LED blinkin : Possible cause of failure is in SC board
No LED blinkin (Li htin or no li htin ): Possible cause of failure is in SU or SD board
4. After inspection, turn off the TV/Display Unit and wait a few minutes to dischar e.
5. Remove SC ji from SC board.
Remark: This SC ji can be used for all 2009 Plasma TV and Plasma Display.
18
All manuals and user guides at all-guides.com

8 Disassembly and Assembly Instructions
8.3.
8.1. Remove t e Rear cover
1. See Service Hint (Section 3)
8.2. Remove t e P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for dis
char e from electrolysis capacitors.
1. Unlock the cable clampers to free the cable
2. Disconnect the connectors (P2, P6, P7, P9, P11, P25,
P34 and P35).
3. Remove the screws (x9 and remove the P-Board.
Remove t e Side terminal
cover and Rear terminal cover
1. Remove the claw (x 1 ^ ).
2. Remove the Side terminal cover.
3. Remove the Adjustment cover.
4. Remove the screws (x4 ^ , хЗ О , x2 >=►)
5. Remove the Rear terminal cover.
19
All manuals and user guides at all-guides.com

1. Unlock the cable clampers to free the cable.
2. Disconnect the connectors (A1, A7, A8, A11, A12 and
A25).
3. Disconnect the flexible cables (A20, A31, A32 and A88).
4. Remove the screws (x2 x1 O ) and remove the
Tuner unit.
8.4. Remove t e Tuner unit
A32 A31 A20 A25 A8 A7 Tuner unit
А1 A12 A1
1. Remove the Tuner unit. (See section 8.4.)
2. Remove two EDGE SADDLES at top of case.
Twist the EDGE SADDLE to press up at the back and pull
down the front side.
3. Remove the screws (x4 and remove the A-Board.
Caution :
Press up the case not to touch the le of clamper to the A
board.
Pay attention two metal projection О from back side when
removal and assemble.
8.5. Remove t e A-Board
A-Board
20
All manuals and user guides at all-guides.com