Panasonic Viera TH-37PV60EY User manual

TV
REC VCR DVD
VCR
TEXT
N
EXIT
TV/AVGUIDE
F.P. INDEX HOLD
1 2 3
4 5 6
7 8 9
C0
PROGRAMME
DIRECT TV REC
ASPECT
MENU
OK
6
Operating Instructions
Plasma Television
English Please read these instructions before operating your set and retain them for future reference.
The images shown in this manual are for illustrative purposes only.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection
points, where they will be accepted on a free of charge basis. Alternatively, in some countries you
may be able to return your products to your local retailer upon the purchase of an equivalent new
product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate
waste handling. Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method
of disposal.
Printed in Czech Republic
Model No. TH-37PV60EY
TH-42PV60EY
Customer’s Record
The model number and serial number of this product may be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record
of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number Serial Number

2
3
Viewing Advanced FAQs, etc.Quick Start Guide
Contents
Turn your living room into a home theatre!
Experience an amazing level of multi-media excitement
•Safety Precautions ······································ 4
(Warning & Caution)
•Notes ··························································· 5
•Maintenance ··············································· 5
Be Sure to Read
Basic Features
•Watching TV ·············································· 11
•Viewing Teletext ········································ 12
•Watching VCR, DVD and Satellites ·········· 14
Advanced Features
•How to Use Menu Functions ····················· 15
(picture, sound quality, etc.)
•Displaying PC Screen on TV ····················· 19
•Editing and Setting Channels ···················· 20
•Restore Settings ······································· 22
•Owner ID ··················································· 23
•Q-Link Functions ······································· 24
•HDMI Functions ········································ 25
•External Equipment ··································· 28
Enjoy your TV!
•Technical Information ································ 30
•FAQs ························································· 32
•On screen messages ································ 33
•Index ························································· 34
•Licence ······················································ 34
•Specifications ············································ 35
FAQs, etc.
Accessories/Options ············ 6
Identifying Controls ·············· 7
Basic Connection ·················· 8
Auto Setup ······························ 10
Enjoy rich multi-media
Camcorder
Amplifier with
Speaker system
VCR DVD player
DVD recorder
Personal
computer
Satellite receiver
Quick Start Guide
Sharp pictures with HDMI terminal
Control DVD recorder / VCR via TV with Q-Link connection (p. 24)
Create home theatre and DVD recorder link-ups with
"Control with HDMI" without complicated settings!

4 5
Safety Precautions
4 : 3
12
AC 220-240 V
50 / 60 Hz
Do not display a still picture for a long time
This causes the image to remain on the plasma
screen ("after-image").
This is not considered a malfunction and is
not covered by the warranty.
To prevent after-image, the screen saver is
automatically activated after a few minutes if no signals
are sent or no operations are performed. (p. 32)
Electronic equipment
In particular, do not place video equipment near the unit
(electromagnetic interference may distort images / sound).
Equipment with an infrared sensor
This TV also emits infrared rays (this may affect
operation of other equipment).
Keep the unit away from these equipment
Warning & Caution
Typical still images
Channel number and other logos
Image displayed in 4:3 mode
Video game
Computer image
Notes
IMPORTANT: THE MOULDED MAINS PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the mains plug which is
marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the mains plug
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the mains plug
which is marked with the letter L or coloured RED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and replace the fuse.
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your mains plug, proceed as follows.
WARNING: – THIS APPARATUS MUST BE EARTHED.
IMPORTANT: – The wires in this mains lead are coloured in accordance with the following code: –
Green-and-Yellow: Earth
Blue: Neutral Brown: Live
If a new mains plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
If the fitted moulded mains plug is unsuitable for the socket outlet in your home, then the fuse shall be
removed and the mains plug cut off and disposed of safety. There is a danger of severe electrical shock
if the cut off mains plug is inserted into any 13 amp socket.
If the mains plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the mains plug must not be used until a replacement cover is obtained.
A replacement fuse cover may be purchased from your local Panasonic Dealer.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is
fitted in this mains plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating
of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
ASA
or the BSI mark on the body of the fuse.
Handling the mains plug
Ensure that the mains plug is easily accessible at all
times. The On/Off switch on this model does not fully
disconnect the TV from the mains supply. Remove the
mains plug from the wall socket when the TV set is not
used for a prolonged period of time.
Ensure the grounding pin on the mains plug is securely
connected to prevent electrical shock.
An apparatus with CLASS I construction shall be connected
to a mains socket outlet with a protective earthing connection.
Note
If the set is not switched off when the TV station stops
transmitting, it will automatically go to standby mode after
30 minutes. This function will operate only in TV mode.
Do not expose to
direct sunlight and
other sources of heat
Avoid exposing the TV set to direct
sunlight and other sources of heat. To
prevent fire never place any type of
candle or naked flame on top or near
the TV set.
Power source
This TV set is designed to operate on 220-240V,
50 / 60 Hz AC.
Do not remove the cover
Do not remove the rear cover as live parts are
accessible when it is removed. There are no
user serviceable parts inside.
Do not expose to rain or
excessive moisture
To prevent damage which might result in electric
shock or fire, do not expose this TV set to rain
or excessive moisture.
This TV must not be exposed to dripping or
splashing water and objects filled with liquid,
such as vases, must not be placed on top of or
above the TV.
Do not block the rear
ventilation openings
Ventilation should not be impeded by covering
the ventilation openings with items such as
newspapers, tablecloths and curtains.
Cabinet and display panel care
Remove the mains plug from the wall socket.
The cabinet and display panel can be cleaned
with a soft cloth moistened with mild detergent
and water. Do not use solutions containing
benzol or petroleum.
TV sets can produce static electricity, care must
be taken whenever touching the TV screen.
Use only the dedicated
stands / mounting equipment
Using an unauthorized stand or other fixtures may
make the unit shaky, risking injury. Be sure to ask
your local Panasonic dealer to perform setup.
Use optional stands / mounts (p. 6).
Do not place the TV on
sloped or unstable surfaces
The TV may fall off or tip over.
Display panel
Cabinet
Mains plug
Daily care: Gently wipe the surface clean of dirt by using a soft cloth.
Major contamination: Wipe the surface clean using a soft
cloth dampened with clean water or water containing a
small amount of neutral detergent. Then, using a soft dry
cloth, evenly wipe the surface clean until it is dry.
Daily care: Wipe the surface clean using a soft dry cloth.
Major contamination: Dampen a soft cloth with clean water
or water containing a small amount of neutral detergent.
Then, wring the cloth and wipe the surface clean with it.
Finally, wipe the surface clean with a dry cloth.
Wipe the mains plug with a dry cloth at regular intervals.
(Moisture and dust may lead to fire or electrical shock.)
First, remove the mains plug from the socket outlet.
Caution
•
The surface of the display panel has been specially
treated and may be easily damaged.
Do not tap or scratch the surface with your fingernail or
other hard object.
•
Use care not to subject the surface to insect repellent,
solvent, thinner, or other volatile substances
(this may degrade surface quality).
Caution
•
Use care not to subject the TV unit's surfaces to detergent.
(A liquid inside the TV unit could lead to product failure.)
•
Use care not to subject surfaces to insect repellent,
solvent, thinner, or other volatile substances
(this may deteriorate the surface by peeling the paint).
•
Do not allow the cabinet to make contact with a rubber
or PVC substance for a long time.
Maintenance
Allow sufficient space around
the unit for radiated heat
10
10
6
10
7
(cm)

6
7
Quick Start Guide
AV4
S-V V L R
+
-
-
+
TV
REC VCR DVD
VCR
TEXT
N
EXIT
TV/AVGUIDE
F.P. INDEX HOLD
1 2 3
4 5 6
7 8 9
C0
PROGRAMME
DIRECT TV REC
ASPECT
MENU
OK
1 2 3
4 5 6
7 8 9
0
OK
C
TV
N
Optional accessories
Pedestal Plasma TV stand Wall-hanging
bracket
(vertical)
TY-WK42PV3W
(angle)
TY-WK42PR2W
TY-ST42P600W TY-S37PX60W
(TH-37PV60EY)
TY-ST42P60W
TY-S42PX60W
(TH-42PV60EY)
Installing remote's batteries
Batteries for the Remote
Control Transmitter (2)
•
R6 (UM3)
Identifying ControlsAccessories/Options
Clamper (2)
•
TMME258 Mains Lead
•
K2CT3DH00018
1Pull
open
Hook
2
Note the correct
polarity (+ or -)
Close
Snap open
Snap shut
Rear of the TV
Caution
•
Incorrect installation may cause battery
leakage and corrosion, resulting in
damage to the remote control unit.
Do not mix old and new batteries.
Do not mix different battery types (such
as alkaline and manganese batteries).
Do not use rechargeable (Ni-Cd)
batteries.
•
Do not burn or breakup batteries.
Remote Control
Transmitter
•
EUR7651090
Operating Instructions
Pan European Guarantee Card
Attaching the cable clampers
•
Do not bundle the RF cable and mains lead together (could cause
distorted image).
•
Fix cables with clampers as necessary.
•
When using the optional accessory, follow the option’s assembly
manual to fix cables.
Function
select
Increases or decreases the programme position by one. When
a function is already displayed, press to increase or decrease
the selected function. When in Standby mode, switches TV On.
Standby On / Off switch
(Switches TV On or Off standby)
MAINS Power
On / Off switch
Lift door to open
C.A.T.S. (Contrast Automatic Tracking System) sensor
(senses brightness to adjust picture quality in "Auto" viewing mode) (p. 17)
Power LED
Remote control
signal receiver
STR (Normalisation store)
(Stores tuning and other
function settings)
TV/AV switch
Sound mute On / Off
• Volume / Contrast / Brightness / Colour /
Sharpness / Tint (NTSC mode) / Bass / Treble /
Balance / Manual tuning (p. 20)
Changes picture aspect ratio
(p. 11)
Normalises (p. 16)
(Resets all settings to their default levels)
Selects programmes in sequence
Direct channel access
Use together with numeric buttons to
access TV channels by entering broadcast
channel number.
(p. 11)
Programme / channel change buttons (0-9)
and Teletext page buttons.
(p. 11 and p. 12)
When in Standby mode, switches TV On.
Viewing a favourite teletext channel
(p. 13)
Teletext (p. 12)
MENU
Press to access the Picture, Sound
and Setup menus (p. 16)
Cursor buttons to make
selections and adjustments
Programme Guide (p. 11)
VCR / DVD operations (p. 14)
Volume
Programme Information (p. 11)
Teletext Index (p. 13)
Still Picture (p. 11)
Coloured buttons used for
the selection, navigation and
operation of various functions.
EXIT (Returns to TV screen)
Switch between viewing TV or
AV input. (p. 14)
DIRECT TV Recording
To immediately record programme
in VCR / DVD recorder with Q-Link
connection (p. 24)
Standard accessories
•
Identifying Controls
•
Accessories/Options
Check that you have the accessories and items shown
Remove from the TV unit
Push both side
hooks and pull
out
Headphones jack (p. 28)
AV4 terminals
(p. 28)
Ferrite core
•
J0KF00000018
•
Red light indicates Standby mode. When
using the remote control, indicates the TV
has received a command.
OK button to confirm
selections and choices.
Press after selecting programme
positions to avoid delay.

8
9
Quick Start Guide
RF OUT
RF IN
RF OUT
RF IN
RF IN
RGB
VIDEO
S-VIDEO
AV1
VIDEO
S-VIDEO
RGB
VIDEO
AV3
(Q-Link)
AV2
(Q-Link)
COMPONENT
COMPONENT
RGB
VIDEO
S-VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
AV3
(Q-Link)
AV2
(Q-Link)
AV1
COM PONENT
AV1
RF OUT
RF IN
RGB
VIDEO
S-VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
AV3
(Q-Link)
AV2
(Q-Link)
Basic Connection
DVD Recorder
or VCR
SCART cable
(fully wired)
RF cable
Aerial
Mains lead (supplied)
Clamper
•
To unfasten
Mains lead (supplied) Mains lead (supplied)
SCART cable
(fully wired)
DVD Recorder or VCR
RF
cable
Aerial Aerial
Rear of the TV Rear of the TV
SCART: 21 pin connection used for video, audio and switching signals (Also known as Euro SCART and Peritel)
RF: Radio Frequency - Signal received from terrestrial aerial.
RGB / S-Video / Video:
Choose between these three video formats depending on personal preference and equipment requirement.
(RGB - Red, Green and Blue)
VCR: Video Cassette Recorder
Rear of the TV
Satellite receiver
External equipment and cables shown are not supplied with this TV.
Please ensure that the TV is disconnected from the mains socket before attaching or disconnecting any leads.
•
Basic Connection
SCART cable
(fully wired)
Ex.1Connecting aerial
(TV only) Ex.2
Connecting DVD Recorder (VCR)
(TV, DVD Recorder and VCR )
Note
•
Connect to AV3 for a DVD Recorder / VCR supporting Q-Link (p. 24).
•
Connect to AV1 for a Satellite receiver.
•
If connecting the TV and Satellite receiver with SCART cable, you can watch satellite broadcast by RGB input signal.
Ex.3Connecting DVD Recorder (VCR) and Satellite receiver
( TV, DVD Recorder, VCR and satellite )
AC 220-240 V
50 / 60 Hz
SCART cable
(fully wired)
RF cable
RF cable
RF cable
RF cable
RF cable

10 11
MENU
OK
OK
OK
EXIT
ViewingQuick Start Guide
IDTV
VCR
EXITMENU
1 2 3
4 5 6
7 8 9
0
OK
0123456789
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
PIN NUMBER :
NAME :
POSTCODE :
Owner ID
HOUSE NO :
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗
Exit
Select character
Change character
Store Owner ID
AUTO SETUP IN PROGRESS
SEARCHING : PLEASE WAIT
01 99:21 41
CH12
Exit
DOWNLOAD IN PROGRESS
PLEASE WAIT
Programme : 63
Remote control unavailable
0123456789
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
PIN NUMBER :
NAME :
POSTCODE :
Owner ID
HOUSE NO :
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗
Exit
Select character
Change character
Store Owner ID
TV
VCR
EXIT
GUIDE
HOLD
1 2 3
4 5 6
7 8 9
C0
ASPECT
OK
Plug the TV into mains socket and switch On
(Takes a few seconds to be displayed)
Usable characters and numbers
1
(example: Owner ID)
On-screen operation
guide will help you.
Auto Setup
Following the on-screen operation
guide, enter your own choice of PIN
number, name, etc.
•
For detailed procedures
"Owner ID" (p. 23)
•
Make a note of the PIN number
in case you forget it.
Search and store TV channels automatically.
These steps are not necessary if the setup has been completed your local dealer.
■
When inputting owner ID
Auto Setup is now complete and your TV is ready for viewing.
■
When inputting owner ID later
EXIT
•
You can now use the remote
control to turn On the unit or turn
the unit to standby mode.
(Power LED: On)
2
•
If you input the ID later
"Owner ID" (p. 23)
•
If a compatible recording equipment
with Q-Link or similar technologies
(p. 24) is connected, channel
information is automatically
downloaded to the equipment.
•
Auto Setup will start to search for
TV channels and store them.
•
To check programme list
at-a-glance
Programme Guide (p. 11)
•
To edit channels
"Programme edit" (p. 21)
•
Watching TV
•
Auto Setup
•
The sorted programme order
depends upon the TV signal,
the broadcasting system and
reception conditions.
■
ON SCREEN HELP Instructions box
used to open the main menus and to
return to the previous menu
used to exit the menu system and
return to the normal viewing screen
used to move the cursor and select
menus
used to access menus, adjust levels or
to select from a range of options
used to store settings after adjustments
have been made or options have been
set
Many features available on this TV can be accessed via the On Screen Display menu.
Note
•
If tuning and downloading
data have failed, perform
"Auto setup" (p. 21).
•
If you turned the TV Off during
Standby mode last time, the
TV will be in Standby mode
when you turn the TV On with
MAINS power On / Off switch.
■
To select a channel using programme guide
VCR
1 2 3
4 5 6
7 8 9
0
Watching TV
Select a channel
up
Volume
2
1
1
CH_ _
Turn power on
BBC 1
HOLD
Freeze / unfreeze picture
Hold
Display
status
information
Display / hide status information
•
Displays information for a few seconds.
■
Other useful functions (Operate after )
MAINS power On / Off switch should be On.
Picture will appear.
(Press for about 1 second)
down
Change
aspect
ratio
or
14 : 9
A
SPECT
•
Each press changes the mode.
While the bar is displayed
red
green
Auto aspect / 16:9 / 14:9 / 4:3 /
Zoom1 / Zoom2 / Zoom3
Using the
On Screen
Displays
■
How to use remote control
•
To change the mode with colour buttons
Change the aspect ratio (p. 30)
Enjoy viewing the picture at its optimum size and aspect
1
OK
select
watch
GUIDE
■
To select a channel inputting the channel number, e.g. 39.
C
→
3
→
9
select page
Programme Guide
Prog. Name Chan.
VCR :
1 :
2 :
3 :
4 :
5 :
6 :
7 :
8 :
9 :
10 :
11 :
12 :
CH21
CH44
CH51
CH41
CH47
CH23
CH26
CH58
-
-
-
-
-
BBC1
BBC2
ITV
S4C
Prog. Name Chan.
13 :
14 :
15 :
16 :
17 :
18 :
19 :
20 :
21 :
22 :
23 :
24 :
-
-
-
-
-
-
-
-
-
-
-
-

12
13
Viewing
MENU
MENU
red
green
Viewing Teletext
You can enjoy news, weather forecasts and subtitles, etc. (depending on the broadcaster)
FULL /
TOP /
BOTTOM
Reveal
hidden
data
(TOP) (BOTTOM) Normal (FULL)
•
Re-hide
red
Reveal hidden words e.g. quiz page answers
•
Viewing Teletext
Switch to Teletext
Select the page
■
To adjust contrast
MENU
<< 01 02 03 04 05 06 07 >>
TELETEXT
INFORMATION
17:51 28 Feb
•
Displays the
index page
(content varies
depending on the
broadcasters)
VCR
1 2 3
4 5 6
7 8 9
0
up
or or
(Corresponds to the colour bar)
down
red
green
yellow
blue
(Press twice)
(Press twice)
■
Using teletext
What is FASTEXT mode (default)?
In FASTEXT mode, four differently coloured subjects are situated at the bottom of the display. To access more information about one
of these subjects, press the appropriately coloured button. This facility enables fast access to information on the subjects shown.
What is List mode?
In List mode, four differently coloured page numbers are situated at the bottom of the screen. Each of these
numbers can be altered and stored in the TV’s memory. ("Store frequently viewed pages", p. 13)
■
To change mode "Teletext" in Setup menu (p. 18)
OK
Note
•
Contrast will be lowered
in the still picture to
prevent after-image.
Time / date
Current
page
number
Sub page number
Colour bar
As the blue bar is displayed
(Expand the BOTTOM half)
TEXT
■
To return to TV
TEXT
•
Press once to have picture and text.
Press again to return to TV.
TV
VCR
TEXT F.P. INDEX HOLD
1 2 3
4 5 6
7 8 9
0
MENU
OK
1
2
Store
frequently
viewed
pages
View in
multi
window
HOLD
Call up a
favourite
pages
Watch
TV while
waiting
for update
HOLD
If you wish to hold the current page without updating
Stop automatic updating
MENU
yellow
yellow
Appears
when
updating is
completed
(You cannot change the channel.)
Teletext automatically updates itself when new information becomes available.
•
The news page provides a function that indicates arrival of latest news ("News Flash").
Changes to TV screen temporarily
View the
updated
page
TEXT
Watch TV and Teletext in two windows at once
•
Operations can be made only in Teletext screen.
•
Each time pressed: Teletext TV and Teletext
TV
INDEX
View sub
page
INDEX
F.P.
•
Call up the page stored in "blue".
•
Factory setting is "P888" (subtitle service) on blue button.
View favourite page by pressing F.P. button
•
FASTEXT mode only
Return to the main index page
OK
Enter the
4-digit number
example: P6
Appears at top of the
screen
■
To view specific sub page
MENU
•
Sub pages:
The number of sub pages varies depending on the broadcasters (up to 79 pages).
It may take some time for searching, during which time you can watch TV.
OK
blue
Store frequently viewed pages
(only on first 25 channels on Programme Guide)
in the colour bar
(List mode only)
press
and
hold
As page is
displayed
The number changes to white.
Corresponding
colour button
•
If you wish to use
Subtitles, do not
change number on
blue button.
■
To change stored pages
blue
VCR
1 2 3
4 5 6
7 8 9
0
OK
press
and
hold
Enter new page number
■
To resume
HOLD
Colour button you
want to change
View sub page (Only when teletext is more than one page)
View theTV picture while searching for a teletext page
0
0
6
0
blue

14 15
TV
TV/AV
PROGRAMME
OK
REC VCR DVD
HDMI1/2
OK
Viewing Advanced
TV/AV
Watching VCR, DVD and Satellites
2
3
The Remote Control is capable of operating some functions of selected Panasonic VCRs and DVD
(Digital Versatile Disc) equipment.
Connect the Satellite receiver and you can watch satellite broadcasts.
To connect the equipment (p. 8)
Select the connector
connected to the equipment
AV1 AV2/
S-video
AV3/
S-video
AV4/
S-video
Component/
PC
(AV mode screen)
Note
•
If the external equipment has an aspect adjustment function, set to "16:9".
•
For details, see the manual of the equipment or ask your local dealer.
•
HDMI (p. 25)
■
To return to TV
TV/AV
•
example: AV1
red
PC
blue
yellow
(twice)
Select the external input
green
red
yellow
green
yellow
blue
red
HDMI1/
HDMI2
blue
Displays the selected connector
1Turn the TV on
■
When connecting with SCART as example 2 or 3 (p. 8 and p. 9)
Receives input signals automatically when playback starts or
satellite receiver is switched on
•
Input signals are automatically identified by the SCART (pin 8) terminal.
•
This function will be available for HDMI connection too (p. 25).
■
If input mode is not switched automatically
Perform and
•
When colour bar disappears Press any coloured buttons
•
You can also select the connector using the TV/AV button on the front panel of the TV.
Press the button repeatedly until you reach the connector to view.
Some Panasonic VCR and DVD equipment connected to the TV unit can be directly operated with the remote control.
VCR DVD
VCR / DVD switch
Select VCR / DVD
Standby
Set to Standby mode / Turn on
Play
Playback videocassette / DVD
Stop
Stop the operations
Rewind / Skip / Search
VCR: Rewind, view the picture rapidly in
reverse
DVD: Skip to the previous track or title
Press and hold to search backward
Fast-forward / Skip / Search
VCR: Fast-forward, view the picture
rapidly forward
DVD: Skip to the next track or title
Press and hold to search forward
Pause
Pause / Restart
DVD: Press and hold to play at slow speed
PROGRAMME
Programme Up / Down
Select programme
REC
Record
Start recording
•
Dependant on DVD/VCR setup
Terminal
AV1 AV2 AV3 AV4
Compo-
nent PC HDMI1 HDMI2
Manual input
selection
AV1
AV2
AV2S
(S-video input)
AV3
AV3S
(S-video input)
AV4
AV4S
(S-video input)
Compo-
nent PC HDMI1 HDMI2
Auto input
selection
EC1/RGB
AV1/RGB
(RGB input)
EC2
EC3/RGB
AV3/RGB
(RGB input)
― ― ―
EC/
HDMI1 HDMI2
Screen display
Main menu
Picture menu
Sound menu
Setup menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
3D-COMB
Normal
On
On
P-NR Off
Picture menu
Dynamic
Advanced setting Access
-
+
-
+
-
+
-
+
change or access
select
Only available in NTSC / PAL
Bass
-
+
-
+
-
+
Treble
Balance
Headphone volume
NICAM
Mode
Ambience
Sound menu
Off
Music
HDMI1 input Auto
Off
Only available in HDMI
W / B High R
W / B High B
W / B Low R
W / B Low B
Gamma 2.2
Advanced setting
Only available in PC
Colour balance Normal
Sharpness
Access
Tuning menu
Changed
Number and positions of alternatives
Moved
Displays the next screen
■
Choose from among alternatives
■
Adjust using the slide bar
■
Go to the next screen
How to Use Menu Functions
Not available in PC, HDMI and HD signal
Only available in NTSC signal
•
How to operate (p. 16)
NTSC (National Television System Committee): One of television signal used in USA, etc.
HD signal: High-definition signal
(p. 19)
Programme edit
Auto setup
Manual tuning
Tuning menu
Access
Access
Access
Fine tuning
Delete Add Move Download
Programme edit
Prog. Chan. Name Lock
1 :
2 :
3 :
4 :
5 :
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
PC setup
Control with HDMI
Off timer
Tuning menu
Setup menu
Access
On
Q-Link AV2
AV2 out Monitor
Off
Power on preference TV
Access
Teletext FASTEXT
Power save Off
Side panel Off
Volume correction
Owner ID
Shipping condition
Access
Access
0123456789
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
PIN NUMBER :
NAME :
POSTCODE :
Owner ID
HOUSE NO :
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗
Exit
Select character
Change character
Store Owner ID
All tuning data will be erased
Shipping condition
Exit
Return
Start
Clock
Input resolution
H-pos
V-pos
Clock phase
Sync H & V
VGA
PC setup
Only available in PC
(p. 19)
(p. 20)
(p. 22)
(p. 23)
AUTO SETUP IN PROGRESS
SEARCHING : PLEASE WAIT
01 99:21 41
CH12
Exit
Return
Manual tuning
01 99:21 41
CH12
1
Exit
Search down/up
Return
Direct entry
Store
C 0 9
•
How to Use Menu Functions (picture, sound quality, etc.)
•Watching VCR, DVD and Satellites
Only available in AV, PC and HDMI

Advanced
Main menu
Picture menu
Sound menu
Setup menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
Normal
On
Off
Picture menu
Dynamic
3D-COMB On
TV
N
EXITMENU
OK
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
Normal
On
Off
3D-COMB On
Picture menu
Dynamic
Colour balance Normal
Sharpness
OK
MENU
OK
OK
16
17
How to Use Menu Functions
Display menu
3
2
4
Various menus allow you to make settings for the picture, sound, and other functions.
•
Displays the functions that can be set
(varies according to the input signal)
Note
•
To initialize all settings
"Shipping condition"
(p. 22).
■
To return to TV
at any time
EXIT
■
To return to the
previous screen
MENU
Select the menu
Select the item
(example: Picture menu)
select
select
Adjust or select
change
(example: Picture menu)
(example: Picture menu)
Changed
Number and positions
of alternatives
Moved
■
Choose from among alternatives
■
Adjust using the slide bar
■
To reset the setting
N
access
store
(Required by some
functions)
•
Setup menu (p. 18)
■
Menu list
•How to Use Menu Functions
(picture, sound quality, etc.)
•
A different menu will be displayed while PC is used. (p. 19)
•
In AV mode, the Sound menu gives a reduced number of options.
Menu Item Adjustments / Configurations (alternatives)
Picture menu
Viewing mode
Selects four different screen settings (Dynamic / Normal / Cinema / Auto)
In each Viewing mode setting, Contrast, Brightness, Colour, Sharpness, Tint (in NTSC
only), Colour balance, Colour management and 3D-COMB can be adjusted and stored
to suit your particular viewing requirement (e.g., you may require different settings for
viewing sports, films, news etc.)
Changes to any settings in a viewing mode will affect all signal sources: RF, AV1, AV2,
AV3, AV4, Component, PC and HDMI
Changes will be stored automatically. By analysing and processing the incoming
picture, all four modes feature automatic enhancement
Adjust by each viewing mode
Contrast
Brightness
Colour
Sharpness
Increases or decreases the levels of these options according to your personal preference
Tint With an NTSC signal source connected to the TV, the picture hue can be adjusted to
suit your taste
Colour balance Allows you to set the overall colour tone of the picture (Cool / Normal / Warm)
Colour
management Automatically adjusts colours to vivid ones (Off / On)
P-NR
Picture Noise Reduction
Automatically reduces unwanted picture noise (Off / Min / Mid / Max)
•
Not valid on PC signal
3D-COMB
Occasionally, whilst viewing still or slow moving pictures, colour patterning may be seen
Set to On to display sharper and more accurate colours (Off / On)
•
For PAL or NTSC signal reception only
•
Not valid on RGB, S-Video, components, PC and HDMI
Sound menu
Bass Increases or decreases level to enhance or minimise lower, deeper sound output
Treble Increases or decreases level to enhance or minimise sharper, higher sound output
Balance Adjusts volume level of right and left speakers
Headphone volume Adjusts the volume of the headphones
NICAM
NICAM (Near Instantaneous Companded Audio Multiplex)
A format for digital sound over television
Reproduces stereo sound (Off / On)
•
Off if reception is poor (FM monaural sound)
Mode
Sound quality can be improved when watching music scene or drama (Music / Speech)
Ambience Provides a dynamic enhancer to simulate improved spatial effects (Off / On)
HDMI1 input
Select to fit the input signal
(Auto / Digital / Analogue) (p. 25)
Auto : Automatic detection of digital or analogue sound source
Digital : HDMI cable connection
Analogue : HDMI-DVI adapter cable connection
•
HDMI input mode only
•
HDMI2 terminal is for digital signal only
•
No setting for HDMI2 available
1
•
Resets each Viewing mode (Dynamic / Normal / Cinema) to the default
settings.
P-NR in Picture menu is reset to off.
•
Aspect mode is also reset to Auto aspect.

Advanced
TV
TV/AV
PROGRAMME
OK
REC VCR DVD
HDMI1/2
TV/AV
18
19
How to Use Menu Functions
■
Menu list
•Displaying PC Screen on TV
•How to Use Menu Functions (picture, sound quality, etc.)
Menu Item Adjustments / Configurations (alternatives)
Setup menu
Q-Link Selects which AV terminal is to be used for data communication between this TV and a
compatible recording equipment (AV2 / AV3) (p. 24)
AV2/AV3 out
Chooses the signal to be transmitted from the TV to Q-Link (TV / AV1 / AV2 / AV3 /
AV4 / Monitor)
•
Monitor: Image displayed on screen
•
Component, PC and HDMI signals cannot be outputted
Control with HDMI Control with HDMI function (Off / On) (p. 26)
Teletext Teletext display mode (FASTEXT / List) (p. 12)
Off timer Sets the time the unit automatically turns Off. (Off / 15 / 30 / 45 / 60 / 75 / 90) (minutes)
Volume correction Adjusts volume for AV, PC and HDMI mode
Side panel Increases the brightness of the side panel (Off / Low / Mid / High)
•
The recommended setting is "High" to prevent panel "after-image"
Power save Reduces brightness of picture to economise on power consumption (Off / On)
Power on preference
Set to "TV" to view picture from TV tuner.
Set to "AV" to view input from an external equipment connected to a SCART terminal,
e.g. satellite receiver
(TV / AV)
•
The external equipment must be switched on and sending a control signal for
automatic switching at power on to occur
Tuning menu
Programme edit Edits channels (p. 21)
Auto setup Sets channels automatically (p. 21)
Manual tuning Sets channels manually (p. 21)
Fine tuning
Fine tuning of channels (during rain, etc.)
Owner ID Inputs the owner ID (p. 23)
Shipping condition Resets all settings, for example, when moving (p. 22)
•
A different menu will be displayed while PC is used. (p. 19)
•
In AV mode, the Setup menu gives a reduced number of options.
■
To return to TV
TV/AV
yellow
(Press twice)
Displaying PC Screen on TV
Select the external input
Select "PC"
2
The screen of the PC connected to the unit can be displayed on the TV.
You can also listen to PC sound with the audio cable connected. To connect PC (p. 28)
Displays PC screen
•
Corresponding signals
(p. 31)
•
If "H-freq." or "V-freq."
is shown in red, the
signals may not be
supported.
■
PC menu setting (changed as desired)
•
To make settings "How to Use Menu Functions" to (p. 16)
Menu Item Adjustments / Configurations (options)
Picture menu
Viewing mode, Contrast, Brightness, Sharpness, Colour balance (p. 17)
Advanced
setting
W/B High R White balance of bright red area
and
repeatedly adjusted
W/B High B White balance of bright blue area
W/B Low R White balance of dark red area
W/B Low B White balance of dark blue area
Gamma (2.0 / 2.2 / 2.5 / S Curve)
Setup menu
PC
setup
Input
resolution
Switches to a wide view
•
VGA (640 x 480 dots), WVGA (852 x 480 dots),
XGA (1,024 x 768 dots), WXGA (1,366 x 768 dots)
•
Options change depending on signals
Clock Set to the minimum level if noise occurs
H-pos
Adjusts horizontal position
OK
V-pos
Adjusts vertical position
OK
Clock phase Eliminates flicker and distortion
•
Adjust after Clock adjustment • Set to the minimum level if noise occurs
Sync
Chooses another synchronous signal if the image is distorted (H&V / On G)
•
H&V : by the horizontal and vertical signals from your PC
On G : by the green signal from your PC (if available)
Volume correction, Side panel, Power save (p. 18)
•
Sound menu (p. 17)
1
blue
To
next
page

Advanced
Main menu
Picture menu
Sound menu
Setup menu
Access
Q-Link
Control with HDMI
Off timer
Tuning menu
Owner ID
Shipping condition
Setup menu
AV2
On
AV2 out Monitor
Off
Power on preference TV
Teletext FASTEXT
Side panel Off
Power save Off
Programme edit
Auto setup
Manual tuning
Tuning menu
Access
Fine tuning
TV
EXITMENU
OK
STR F - / + / TV / AV
CH12
1
Manual tuning
01 99:21 41
- , + : Search
TV / AV : Move cursor
STR : To store
F : To exit
AV4
S-V V L R
AdDelete d DownloadMove
Programme edit
Prog. Chan. Name Lock
2 :
4 :
5 :
CH51
CH47
CH37
Off
Off
Off
XYZ
1 : CH44 OffABC
123
456
:3 CH41 OffFTP
Programme edit
Prog.
ABCDEFGHIJKLMNOPQRST
UVWXYZ+ - . 0123456789
Chan. Name Lock
1 :
2 :
3 :
4 :
5 :
CH44
CH51
CH41
CH47
CH37
Off
Off
Off
Off
Off
XYZ
FTP
123
456
Programme edit
Prog. Chan. Name Lock
1 :
2 :
3 :
4 :
5 :
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
All current tuning
data will be erased
WARNING
Exit
Return
Start Auto Setup
AUTO SETUP IN PROGRESS
SEARCHING : PLEASE WAIT
01 99:21 41
CH12
Exit
Return
Manual tuning
01 99:21 41
CH12
1
Exit
Search down/up
Return
Direct entry
Store
C
09
3 FTP
MENU
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
20
21
(Press repeatedly until "Tuning mode" appears)
or (Access "Manual tuning")
(Select programme position or channel number)
• Selected item will flash.
or (Change programme position or start searching channels)
(Store)
- (Repeat)
Editing and Setting Channels
Select "Setup menu"
Select "Tuning Menu"
3
2
Select the function
4
Display the menu
5How to set
For Manual tuning, using the buttons on
the front of the set ("Manual tuning" on p. 7)
Programme
position (flash)
Channel number
(flash)
Channel
The channel settings can be changed according to your needs and reception conditions.
■
To return to TV
■
To return to TV
EXIT
(Manual tuning screen)
Edit
channels
■
Delete
■
Add
■
Move
■
Change
name
■
Lock
■
Download to
equipment
Programme
edit
Set
automatically
Auto setup
Set
manually
Manual
tuning
■
To download channel
information to a Q-Link
compatible equipment
connected to the unit
blue
Automatically
transmitted
(for a few sec.)
•For details (p. 24)
■
To lock
■
To change the name of the broadcaster
displayed when selecting channels
Cursor
Usable characters
Select the
"Name" field
Select the
character
To next
character
Repeat
Select the
"Lock" field
Select "On"
Start Auto setup
start
Settings are made automatically
Select the programme position
and search through the channel
Store
search
Programme
position
Channel
Repeat
and
Select the channel to edit
Note
•
If a VCR is
connected with
only the RF
cable, select
programme
position "0".
Channel
Name
Edit
•
You cannot select the channel with numeric
buttons or the "C" button when locked.
Store
•
The settings are
downloaded to a Q-Link
compatible equipment
connected to the unit.
•
All previous settings are
erased.
•
No data is stored if an
Auto setup sequence is
interrupted.
•
The
programme
position
blinks.
Automatically set the channels received in the area
To freely change settings after Auto setup
■
To delete
red
After confirming, press
red
■
To add
green
After confirming, press
green
■
To move
yellow
OK
Select new
position
yellow
•Editing and Setting Channels
Edit the programme position settings
•
When the operation is completed,
the broadcast of programme
number "1" will appear.
"Off" to
unlock
)
(
access
select
access
select
access
select
select
1

Advanced
OK
OK
OK
OK
22
23
Main menu
Picture menu
Sound menu
Setup menu
Q-Link
Control with HDMI
Off timer
Tuning menu
Owner ID
Shipping condition
Setup menu
AV2
On
AV2 out Monitor
Off
Power on preference TV
Access
Teletext FASTEXT
Power saveOff
Side panel Off
IDTV
VCR
EXIT
1 2 3
4 5 6
7 8 9
0
MENU
OK
MENU
3
2
4
Select "Setup menu"
Select "Shipping condition"
Display the menu
How to set
■
To return to TV
EXIT
Restore Settings
Check the message and initialise
Follow the on-screen instructions
•
"Auto Setup" will automatically start when MAINS power On / Off switch is next
turned On. (p. 10)
■
To re-tune TV channels only, e.g. after moving house
•
"Auto setup" (p. 21)
All tuning data will be erased
Shipping condition
Exit
Return
Start
Shipping
condition
Restore
Settings
OK
set
Resets the TV to its original condition, i.e. no channels tuned in.
All settings other than "Owner ID" (channels, picture, sound quality, etc.) are reset.
Enter the 4-digit PIN number of your choice
•Make a note of the PIN number in case you forget it.
Enter your name, address, and post code, in that order
Store
0123456789
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
PIN NUMBER :
NAME :
POSTCODE :
Owner ID
HOUSE NO :
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
∗ ∗ ∗ ∗
AV4
S-V V L R
NAME : A
POSTCODE :
Owner ID
HOUSE NO :
VCR
1 2 3
4 5 6
7 8 9
0
OK
OK
OK
OK
Owner ID
Input
owner ID
Owner ID
To change the stored information
Characters Entry field
Select
the entry field To check the "personal information" stored
Hold down for
about 6 sec.
Displays the information
on the screen
(for several sec.) •
The PIN number is
not displayed.
Enter the
PIN number
0
-
9
•Owner ID
•Restore Settings
Select
character
To next
character
store
OK
Q-Link
Control with HDMI
Off timer
Tuning menu
Owner ID
Shipping condition
Setup menu
AV2
On
AV2 out Monitor
Off
Power on preference TV
Access
Teletext FASTEXT
Power saveOff
Side panel Off
3
4
Select "Owner ID"
How to set
■
To return to TV
EXIT
Entry of the security code (PIN number) and "personal information" (your name, address and post code).
In the unfortunate event of theft it will help the Police to determine the owner.
If you have skipped the Owner ID input in "Auto Setup" (p. 10), and input it later, start from .
If you input the Owner ID in "Auto Setup" (p. 10), perform .
(Press twice)
access
select
access
select
Main menu
Picture menu
Sound menu
Setup menu
MENU
Select "Setup menu"
Display the menu
access
select
1
IDTV
VCR
EXIT
1 2 3
4 5 6
7 8 9
0
MENU
OK
2
1
access
select

Advanced
24
25
Q-Link Functions
Q-Link connects the TV unit and VCR / DVD recorder, enables easy recording and playback.
■
Condition
■
Features available
Some recording equipments are not applicable. Read the manuals of the equipment.
What you
see is
What you
record
Information
/ Message
Power
on link
and Easy
playback
Power off
link
Recording information or if recording is not possible, a message is displayed.
(Only when the programme number is "0" or "AV mode" for some equipment.)
When VCR or DVD recorder starts playback or direct navigator or function menu
are activated, the TV is turned on and input mode is switched automatically so
that you can view the content. (Only when TV is in Standby mode.)
When TV is set to Standby mode, the recording equipment is also automatically
set to Standby. (Only when the videocassette or DVD is not active.)
•
Use the VCR / DVD recorder with the following logos:
"Q-Link", "NEXTVIEWLINK", "DATA LOGIC", "Easy Link", "Megalogic", or "SMARTLINK"
•
Connect the equipment to this unit’s AV2 or AV3 terminal via a "fully-wired" SCART cable. (p. 28)
•
Q-Link terminal setup in Setup menu (Q-Link, AV2/AV3 out). (p. 18)
• "DATA LOGIC" (a trademark of Metz Corporation) • "Megalogic" (a trademark of Grundig Corporation)
• "Easy Link" (a trademark of Philips Corporation) • "SMARTLINK" (a trademark of Sony Corporation)
Read the manuals of the equipment too.
■
Download channel settings
•
Perform Auto setup. (p. 21)
When first using this unit, see "Auto Setup". (p. 10)
•
Perform download to the equipment. (p. 21)
•HDMI Functions
•Q-Link Functions
HDMI connection
(∗1): The HDMI logo is displayed on HDMI-compliant equipment.
(∗2): Enquire at your local digital equipment retailer shop.
HDMI (high-definition multimedia interface) allows you to enjoy high-definition digital images and high-quality sound
by connecting the TV unit and the equipment.
HDMI-compatible equipment (∗1) with an HDMI or DVI output terminal, such as a set top box or a DVD player, can
be connected to the HDMI terminal using an HDMI compliant (fully wired) cable.
About connections, see "External Equipment" (p. 28).
Note
•
HDMI is the world's first complete digital consumer AV interface complying with a non-compression standard.
•
If the external equipment has only a DVI output, connect to the HDMI1 terminal via a DVI to HDMI adapter cable (
∗
2).
•
When the DVI to HDMI adapter cable is used, connect the audio cable to the audio input terminal.
•
Audio settings can be made on the "HDMI1 input" menu screen. (p. 17)
•
Applicable audio signal sampling frequencies (2ch L.PCM): 48 kHz, 44.1 kHz, 32 kHz
•
HDMI2 terminal is for digital audio signal only.
•
Use with a PC is not assumed.
•
If the connected equipment has an aspect adjustment function, set the aspect ratio to "16:9".
•
These HDMI connectors are "type A".
•
An equipment having no digital output terminal may be connected to the input terminal of either "Component",
"S-VIDEO", or "Video" to receive analogue signals.
•
The HDMI input terminal can be used with only the following image signals:
480i, 480p, 576i, 576p, 720p and 1080i. Match the output setting of the digital equipment.
•
For details of the applicable HDMI signals, see p. 31.
HDMI Functions
Connections
Function HDMI and SCART SCART (Q-Link) only HDMI only
Easy playback O O O
Direct TV Recording
O
(Not when viewing HDMI input)
O
-
Theatre speaker O
-
O
Power on link O O O
Power off link O O O
TV tuning download O O
-
■
Summary of Control functions
Direct TV Recording:
Recording the current programme in VCR / DVD recorder immediately.
•
When Direct TV Recording is performed, the
recording equipment is automatically turned on if it
is in Standby mode.
•
The recording equipment is recording from its own
tuner. You can turn the TV off during recording.
•
If, during recording from an AV source, you turn the
TV off or change input / programmes, the recording
will be stopped.
IDTV
DIRECT TV REC
DIRECT TV REC

Advanced
Control with HDMI
Setup menu
AV2
Q-Link
Off
On
AV2 outMonitor
TV
Power on preference
Tuning menu
Owner ID
Shipping condition
Off timer
Power save Off
Side panelOff
TV
MENU
OK
MENU
OK
OK
OK
OK
26
27
Select "On"
(default is On)
Select "Setup menu"
Select "Control with HDMI"
2
1
3
Display the menu
∗Enjoy additional HDMI Inter-Operability with Panasonic products which have "HDAVI Control" function.
HDMI connections to some Panasonic equipment (Panasonic DVD Recorder DIGA, Panasonic Player
theatre, Panasonic Amplifier, etc.) allow you to enjoy easy playback or home theatre.
About connections, see "External Equipment" (p. 28). Read the manuals of the equipment too.
This function needs an HDMI compliant (fully wired) cable.
Non-HDMI-compliant cables cannot be utilized.
Consult your local Panasonic dealer or refer to the URL for applicable equipment: www.panasonic.co.uk
Control with HDMI " Control"∗
Preparations
(For the first time / When adding new equipment, reconnecting equipment or changing setup)
After connection turn the equipment on and then switch the TV unit on.
Select the input mode to HDMI1 or HDMI2 (p. 14), and make sure that an
image is displayed correctly.
4
Main menu
Picture menu
Sound menu
Setup menu
Home theatre
HDMI Functions (Continued)
■
To return to TV
EXIT
Easy
playback
Automatic Input switching-When the connected Panasonic equipment is operated,
input mode is switched automatically. When it is stopped operating, input mode is
returned.
Power on
link
When the connected Panasonic equipment starts playback or direct navigator or
function menu are activated, the TV is automatically turned on. (Only when TV is
in Standby mode.)
Power off
link
When TV is set to Standby mode, the connected Panasonic equipment is also
automatically set to Standby.
Theatre
speaker
You can control the theatre speaker with TV’s remote control.
This function is available when Panasonic Amplifier or Player theatre is connected.
Display the menu
MENU
Select "Home theatre" or "TV speaker" ■
Home theatre:
Adjustment for equipment
(automatically turned on if it is in
Standby mode)
•
When selecting "Home theatre", the sound of TV speakers is mute.
•
When the equipment is turned off, TV speakers will be active.
Volume up / down
Mute
■
TV speaker:
TV speakers are active.
Main menu
Picture menu
Sound menu
Setup menu
Home theatre
•HDMI Functions
•
Setup the equipment to enable this function. Read the manual of the equipment.
•
This function may not work normally depending on the equipment condition.
•
This function may not work normally when Panasonic Player theatre is connected.
•
The equipment can be operated by TV’s remote control with this function on even if TV is in Standby mode.
•
Image or sound may not be available for the first few seconds when the playback starts.
•
Image or sound may not be available for the first few seconds when Input mode is switched.
•
Volume function will be displayed when adjusting the volume of the equipment.
•
Easy playback is also available by using the remote control for Amplifier. Read the manuals of Amplifier.
Note
access
select
select
select
access
select
•
Displayed when Amplifier or Player theatre is connected.
This may be displayed after disconnecting the equipment.
In this case, set "Control with HDMI" in Setup menu to
"Off", then set to "On" again.
•
It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG15 (1.5 m)
RP-CDHG30 (3.0 m)
RP-CDHG50 (5.0 m)

Advanced
1
2
AV
AV 1 AV 2 AV 3
PC
AUDIO RGB VIDEO VIDEO VIDEO AUDIO
RGB
VIDEO S-VIDEO S-VIDEO
COMPONENT
AUDIO
IN
L
R
L
R
Y
PB
PR
AV4
S-V V L R
28
29
These diagrams show our recommendations for how to connect the TV unit to your various equipment.
For other connections, consult the instructions for each piece of equipment, the table below, and the specifications (p. 35).
within
10 cm
(VIDEO)
or
(S-VIDEO)
(AUDIO)
Computer
Amplifier with speaker system
Connector
Recording / Playback
(equipment)
AV1 AV2 AV3 AV4 COMPO
NENT
(Front of TV) 1 2
To record / playback videocassettes / DVDs
(VCR / DVD recorder)
To watch DVDs (DVD player)
To watch camcorder images (Video camera)
To watch satellite broadcasts (Set top box)
To play games (Game equipment)
Q-Link
Direct TV Recording
Control with HDMI
: Recommended Connection
PC
Headphones
Camcorder / Game equipment
(Viewing)
(Listening)
Control with HDMI (p. 26)
■Types of connectable equipment to each connector
To listen with speakers
DVD recorder or AV amplifier
External Equipment
Conversion adapter (if necessary)
Press the
cable through
and close
Pull back the
tabs to open
Ferrite
core
(M3
plug)
■
To adjust volume
"Headphone
volume" in the
Sound menu (p. 17)
Satellite receiver
DVD Recorder / VCR
SCART
cable
RF cable
or
(Q-Link)
SCART
cable
(Q-Link)
To watch satellite broadcasts
To record / playback
To watch DVDs
DVD player
•External Equipment
SCART
cable
Y
PB
PR
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name
R GND (Ground) NC (not connected)
G GND (Ground) NC (not connected)
B GND (Ground) HD/SYNC
NC (not connected) NC (not connected) VD
GND (Ground) GND (Ground) NC (not connected)
A PC may be connected to this TV unit so that the PC screen is displayed and sound is heard from the TV.
•
PC signals that can be inputted: Horizontal scanning frequency 31 to 69 kHz; vertical scanning frequency
59 to 86 Hz (more than 1,024 signal lines could result in incorrect display of the image).
•
A PC adapter is not necessary for the DOS/V-compliant D-sub 15-pin connector.
Note •
Some PC models cannot be connected to this TV unit.
•
For details of the applicable PC signals, see p. 31. • Max. display resolution
Aspect 4:3 768 × 720 dots (TH-37PV60EY) 768 × 768 dots (TH-42PV60EY)
16:9 1,024 × 720 dots 1,024 × 768 dots
1
678
3
9
45
10
15 14 13 12 11
2
■PC connection
•
D-sub 15-pin connector signal
Fully wired HDMI
compliant cable
•
Use HDMI2 terminal normally.
•
When using HDMI2 terminal as Control with
HDMI, select the external input to HDMI2 for
the first time (p. 14).
Fully wired HDMI
compliant cable

FAQs, etc.
30
31
Technical Information
Aspect Ratio
Signal name
Aspect modes
Aspect Control Signal
Widescreen signal (WSS)
Control signal through SCART
(pin 8) or HDMI terminal
Auto
aspect 16:9 14:9
4:3 Zoom1 Zoom2 Zoom3 TV AV1 AV2 AV3 AV4 Component AV1 AV2 AV3
HDMI
1
HDMI
2
TV/AV1/AV2/
AV3/AV4
PAL I O O O O O O O O O O O O
-
O O O
- -
PAL 525/60 O O O O O O O
- - - - - -
O O O
- -
M.NTSC O O O O O O O
- - - - - -
O O O
- -
NTSC(AV input only) O O O O O O O
- - - - - -
O O O
- -
Component/HDMI
SD
525(480)/60i O O O O O O O
- - - - - - - - -
O O
525(480)/60p O O O O O O O
- - - - - - - - -
O O
625(576)/50i O O O O O O O
- - - - -
O
- - -
O O
625(576)/50p O O O O O O O
- - - - -
O
- - -
O O
HD
750(720)/50p O O O O O O O
- - - - - - - - -
O O
750(720)/60p O O O O O O O
- - - - - - - - -
O O
1125(1080)/50i O O O O O O O
- - - - - - - - -
O O
1125(1080)/60i O O O O O O O
- - - - - - - - -
O O
PC input
-
O
-
O
- - - - - - - - - - - - - -
Note •
The ratio varies depending on the programme, etc. If the ratio is greater than the standard "16:9",
black bands may appear at the top and bottom of the screen.
•
If the screen size looks unusual when a widescreen-recorded programme is played back on a VCR,
adjust the tracking of the VCR. (See the VCR manual.)
•
Aspect mode can be memorized for SD (Standard definition) and HD (High definition) signals separately.
•
To select the ratio manually: (Only "16:9" or "4:3" in PC mode)
The optimum size and aspect can be chosen, and you can enjoy finer images. (p. 11)
■
Auto aspect: Auto aspect determines the best aspect ratio to use to fill your screen. It does this using a four step
process to determine if the picture being viewed is a widescreen picture.
If Auto aspect detects a widescreen signal it switches into the appropriate 16:9 or 14:9 widescreen mode. If Auto
aspect does not detect a widescreen signal then this advanced TV set enhances the picture for optimum viewing
pleasure.
The text shown on the screen indicates how Auto aspect determined which ratio to use:
"WIDE" appears in the top left of the screen if a widescreen identification signal (WSS) is found or a signal found
through a SCART terminal. Auto aspect switches to the appropriate 16:9 or 14:9 widescreen ratio. This function
will also work in any aspect mode. "Auto aspect" appears in the top left of the screen if black stripes above and
below the picture are detected. Auto aspect chooses the best ratio and expands the picture to fill the screen. This
process can take several minutes, depending on the darkness of the picture.
4:3
14:916:9
Zoom3
Zoom2Zoom1
Directly displays the
image at "16:9" without
distortion (anamorphic).
Displays a "16:9"
letterbox or "4:3" image
without distortion.
Displays the image at
the standard "14:9"
without enlargement.
Displays a "16:9"
letterbox (anamorphic)
image full-screen
without distortion.
Displays the image at
the standard "4:3"
without distortion.
Displays a "2.35:1" letterbox (anamorphic) image full-
screen without distortion. At "16:9", displays the image at its
maximum (with slight enlargement).
4 : 3
14 : 9
16 : 9
Zoom3
Zoom2
Zoom1
Auto aspect
The best ratio is
chosen and the picture
expanded to fill the
screen.
Auto aspect
•Technical Information
SCART, S-VIDEO and HDMI terminal information
Input signal that can be displayed
Socket Earth
CVBS out (video)
CVBS earth
Red in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
CVBS in (video)
RGB status earth
Status RGB
Earth
--
--
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
■
AV1 SCART terminal
(RGB, VIDEO)
Suitable inputs for AV1 include RGB (Red / Green / Blue).
Socket Earth
CVBS out (video)
CVBS earth
S.C. - in
Earth
--
Earth
--
Earth
Audio out (L)
Audio out (R)
CVBS in (video)
Earth
--
Earth
--
Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
■
AV2 SCART terminal
(VIDEO, S-VIDEO, Q-Link)
AV2 - Pins 15 and 20 are dependent on AV2 S-VHS /
VIDEO switching.
Chrominance in
Socket Earth
CVBS out (video)
CVBS earth
Red in, S.C. - in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
CVBS in (video)
Earth
Status RGB
Earth
--
Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
Luminance in
Chrominance earth Luminance earth
■
AV4 S-VIDEO 4 pin terminal
■
AV3 SCART terminal
(RGB, VIDEO, S-VIDEO, Q-Link)
AV3 - Pins 15 and 20 are dependent on AV3 S-VHS /
VIDEO switching.
∗ Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC (D-sub 15P)
Note •
Signals other than above may not be displayed properly.
•
The above signals are reformatted for optimal viewing on your display.
Signal name Horizontal
frequency (kHz)
Vertical
frequency (Hz) Component HDMI PC
525 (480) / 60i 15.73 59.94 ∗ ∗
525 (480) / 60p 31.47 59.94 ∗ ∗
625 (576) / 50i 15.63 50.00 ∗ ∗
625 (576) / 50p 31.25 50.00 ∗ ∗
750 (720) / 60p 45.00 60.00 ∗ ∗
750 (720) / 50p 37.50 50.00 ∗ ∗
1,125 (1,080) / 60i 33.75 60.00 ∗ ∗
1,125 (1,080) / 50i 28.13 50.00 ∗ ∗
640 × 400 @70 Hz 31.46 70.07 ∗
640 × 480 @60 Hz 31.47 59.94 ∗
640 × 480 @75 Hz 37.50 75.00 ∗
800 × 600 @60 Hz 37.88 60.32 ∗
800 × 600 @75 Hz 46.88 75.00 ∗
800 × 600 @85 Hz 53.67 85.06 ∗
1,024 × 768 @60 Hz 48.36 60.00 ∗
1,024 × 768 @70 Hz 56.48 70.07 ∗
1,024 × 768 @75 Hz 60.02 75.03 ∗
1,024 × 768 @85 Hz 68.68 85.00 ∗
1,280 × 1,024 @60 Hz 63.98 60.02 ∗
Macintosh13” (640 × 480) 35.00 66.67 ∗
Macintosh16” (832 × 624) 49.72 74.54 ∗
Macintosh21” (1,152 × 870) 68.68 75.06 ∗
Hot Plug Detect
DDC/CEC Ground
SCL
CEC
TMDS Clock Shield
TMDS Data0−
TMDS Data0+
TMDS Data1 Shield
TMDS Data2−
TMDS Data2+
+5V Power
SDA
Reserved (in cable but N.C. on device)
TMDS Clock−
TMDS Clock+
TMDS Data0 Shield
TMDS Data1−
TMDS Data1+
TMDS Data2 Shield
19
17
15
13
11
9
7
5
3
1
18
16
14
12
10
8
6
4
2
■
HDMI terminal

FAQs, etc.
32
33
FAQs
Before requesting service or assistance, please follow these simple guides to resolve the problem.
If problem still persists, please contact your local Panasonic dealer or Panasonic Customer Care Centre
for assistance. For details (p. 36)
White spots or shadow
images (noise)
•
Check the position, direction, and
connection of the aerial.
Neither image nor
sound is produced
•
Is the unit in "AV mode"?
•
Is the mains lead plugged into the socket
outlet?
•
Is the TV unit turned On?
•
Check Picture menu (p. 17) and volume.
•
Check all required SCART cables and
connections are firmly in place.
Auto aspect
•
Auto aspect is designed to provide you
with the best aspect ratio to use to fill
your screen. For user control please see
p. 30.
Problem Actions
•On screen messages
•Frequently Asked Questions
Problem Actions
logo appears at the
four corners of the screen
Screen
Contrast is reduced
OtherSound HDMI
No sound is produced •
Is "Sound Mute" active? (p. 7)
•
Is the volume set to the minimum?
Sound level is low
or sound is distorted •
Sound signal reception may be deteriorated.
•
Set "NICAM" (p. 17) in the Sound menu to "Off".
Sound is unusual •
Set the sound setting of the connected equipment to "2ch L.PCM".
•
Check the "HDMI1 input" setting in the Sound menu. (p. 17)
•
If digital sound connection has a problem, select
analogue sound connection. (p. 17)
Pictures from external equipment
are unusual when the equipment
is connected via HDMI
•
Is the HDMI cable connected properly? (p. 28)
•
Turn Off the TV unit and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 31)
•
Use an equipment compliant with EIA/CEA-861/861B.
TV unit goes into
"Standby mode" •
The sleep function is activated.
•
The TV unit enters "Standby mode" about 30 min. after broadcasting ends.
The remote control
does not work •
Are the batteries installed correctly? (p. 6)
•
Has the TV unit been switched On?
•
The function to prevent after-image (p. 5) is activated.
(Not a faulty symptom)
•
The screen saver is activated when the following
conditions without any user operation for a few minutes:
● no signal in AV mode
● selected locked channel
•
Contrast is lowered when the following conditions without
any user operation for a few minutes:
● displayed menu (except Tuning menu, Owner ID and
Shipping condition)
"Control with HDMI"
function does not work •
Switch the TV unit on again with the equipment on.
•
Set "Control with HDMI" to "Off", then set to "On" again. (p. 26)
S-Video / black and white picture
•
Using TV/AV button please confirm your selection is S-Video
I.e. AV2/S-Video or AV3/S-Video (p. 14).
On Screen messages - I.e. AV1/EC1
•
You can simply clear these by pressing .
Press again to redisplay.
Direct TV record / Q-Link functions not recording
•
Please confirm SCART cable and connection. Also please
set "AV2/AV3 out" in the Setup menu (p. 18).
Permanently lit spots on
screen •
Due to production process involved in this technology
this may result in some pixels which are permanently lit
or unlit. This is not a malfunction.
Chaotic image, noisy •
Set "P-NR" in the Picture menu (to remove noise). (p. 17)
•
Check nearby electrical products
(car, motorcycle, fluorescent lamp).
No image can be
displayed •
Is "Colour" or "Contrast" in the Picture menu set to the
minimum? (p. 17)
Blurry or distorted image
(no sound or low volume) •
Reset channels. (p. 21)
Problem Actions
On screen messages Actions / Meanings
Please wait.
On screen messages
All tuning data will be erased
Recording in progress
No recording -Check Tape or Disc
•
"Shipping condition" will erase all tuning data.
No recording - UNKNOWN REASON
Please check settings and connections on
HDMI devices.
Recording stopped - TV source changed
Are you sure ?
DOWNLOAD IN PROGRESS PLEASE WAIT
Unable to download, Check Equipment
Feature not available
Incorrect PIN Number
•
Make sure the operation is with your desire.
•
Q-Link channel download is in progress.
•
Check the Q-Link connection and setting (p. 24).
•
The impossible source (Component / HDMI / PC) to be record.
•
The PIN number you entered is wrong.
•
The tape or disc may be "write protected", missing or damaged.
The equipment may already be recording.
•
The recording cannot be done by any reason. Check the equipment.
•
Disc or tape may be full.
•
Communication error in Control with HDMI function (p. 26).
•
No signal can be found in Auto setup.
•
A function is in progress.
•
The recording equipment is recording the programme signal from
its own tuner. You can turn the TV off and leave the equipment
recording in the normal way.
•
Direct TV recording will stop if channel or input source is changed.
WARNING
All current tuning data will be erased
No stations found
Please insert the aerial
•
The tape or disc is active. Stop the equipment and try again.
•
Auto setup will be erased all present tuning data (p. 21).

FAQs, etc.
34
35
Index
Accessories ···························································· 6
Ambience ····························································· 17
Aspect ···························································· 11, 30
Auto Setup ······················································ 10, 21
AV2/AV3 out ··················································· 18, 24
Clamper ······························································ 6, 9
Component ··························································· 31
Connection ······················································· 8, 28
Control with HDMI ·········································· 26, 28
Direct TV Recording ············································· 24
Download to equipment ·································· 10, 21
D-sub 15-pin ························································· 29
DVI········································································ 25
DVDs ···································································· 14
External equipment ·········································· 8, 28
External input ················································· 14, 19
FAQs····································································· 32
Front door ······························································· 7
HDMI ·······························································25-27
Hold ································································ 11, 13
Home theatre ························································ 26
Input signal ··························································· 31
Licence ································································· 34
Lock ······································································ 21
Mains Lead ························································· 6, 8
Maintenance ··························································· 5
Manual tuning ················································· 20, 21
Menu Functions ···············································15-18
NICAM ·································································· 17
Normalise ························································· 7, 16
NTSC ······························································ 15, 35
Off timer ································································ 18
On / Off switch ·················································· 7, 10
Optional accessories ·············································· 6
Owner ID ························································ 10, 23
PAL ······································································· 35
PC··································································· 19, 29
PIN number ···················································· 10, 23
P-NR ····································································· 17
Power LED ······················································· 7, 10
Programme edit ···················································· 21
Q-Link ··································································· 24
Quick Start Guide ··············································6-10
Remote control ··················································· 6, 7
RGB ········································································ 8
Sales and Support Information ····························· 36
Satellite receiver ········································· 9, 14, 28
SCART ····························································· 8, 31
Shipping condition ················································ 22
Specifications ······················································· 35
Sub page ······························································ 13
S-Video ····························································· 8, 31
Teletext ································································· 12
TV speaker ··························································· 27
Video ································································ 8, 14
Viewing mode ······················································· 17
WSS ····································································· 30
Zoom ······························································ 11, 30
A
C
D
E
F
H
I
L
M
O
P
Q
R
S
T
V
W
Z
•Specifications
•Index •Licence
N
Specifications
Note
•
Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
TH-37PV60EY TH-42PV60EY
Power Source AC 220-240 V, 50 / 60 Hz
Power Consumption
Average use 241 W 261 W
Standby condition 0.3 W
Plasma Display panel
Drive method AC type
Aspect Ratio 16:9
Contrast Ratio Max 10000:1
Visible screen size
(No. of pixels)
94 cmV 106 cmV
818 mm (W) × 461 mm (H) ×
939 mm (diagonal)
920 mm (W) × 518 mm (H) ×
1,056 mm (diagonal)
737,280 (1,024 (W) × 720 (H))
[3,072 × 720 dots]
786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
Sound
Speaker 12 cm × 6 cm × 2 pcs, 8 Ω
Audio Output 20 W (10 W + 10 W ), 10% THD
Headphones Φ 3.5 mm stereo mini Jack × 1
PC signals
VGA, SVGA, XGA
SXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems /
Band name
PAL I UHF E21-68 / VHF Ireland channel
PAL 525/60 Playback of NTSC tape from some PAL Video recorders (VCR) or NTSC
disc playback from DVD player and recorder.
M.NTSC Playback from M. NTSC Video recorders (VCR).
NTSC (AV input only) Playback from NTSC Video recorders (VCR).
Aerial - Rear VHF / UHF
Operating Conditions Temperature : 0 °C - 40 °C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
AV3 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV4
VIDEO RCA PIN Type × 1 1.0 V[p-p] (75 Ω)
S-VIDEO Mini DIN 4-pin Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)
AUDIO L - R RCA PIN Type × 2 0.5 V[rms]
Others
COMPONENT Y 1.0 V[p-p] (including synchronization)
PB, PR ±0.35 V[p-p]
HDMI1/2 TYPE A Connectors
PC HIGH-DENSITY D-SUB 15PIN R,G,B/0.7 V[p-p] (75 Ω)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
AUDIO L - R RCA PIN Type × 2 0.5 V[rms]
Output AUDIO L - R RCA PIN Type × 2 0.5 V[rms] (high impedance)
Dimensions ( W × H × D ) 917 mm × 645 mm × 95 mm 1,020 mm × 705 mm × 95 mm
Weight 26.0 k Net 30.0 k Net
Trademark Credits
•
VGA is a trademark of International Business Machines Corporation.
•
Macintosh is a registered trademark of Apple Computer, USA.
•
S-VGA is a registered trademark of the Video Electronics Standard Association. Even if no special notation has
been made of company or product trademarks, these trademarks have been fully respected.
•
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Licence