Panasonic ET-JPF200BU User manual

DPQX1153ZA
Model No. ET-JPF200BU
ET-JPF200WU
Operating Instructions
Floor Stand Kit Commercial Use
Thank you for purchasing this Panasonic product.
■To ensure correct use of this product, please read the instructions supplied with this product and the projector carefully.
■Before using this product, be sure to read “Read this first!” (pages 3 to 4).
■Please save this manual for future use.
* The above illustration is of this product mounted to an optional projector.
ENGLISH
ENGLISH
FRANÇAIS
ESPAÑOL

2 - ENGLISH
Contents
Read this rst! ...................................................................................................3
Product composition.........................................................................................5
Before mounting................................................................................................ 6
Mounting procedure.......................................................................................... 7
Main procedures................................................................................................................. 7
Changing the orientation of the main unit of the projector.................................................. 7
Mounting the oor stand to the projector ............................................................................ 8
Connecting the power cord to the projector...................................................................... 10
Attaching a security wire................................................................................................... 12
Specications ..................................................................................................13
External dimension diagram ............................................................................................. 13
Assembly dimension diagram........................................................................................... 14

ENGLISH - 3
Read this rst!
WARNING
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
zDo not damage the power cord, make any modications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask your dealer to carry out any repairs to the power cord that might be necessary.
Do not use anything other than the provided power cord.
Failure to observe this will result in electric shocks or re. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Completely insert the power plug into the wall outlet and the power connector into the projector
terminal.
If the plug is not inserted correctly, electric shocks or overheating will result.
zDo not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Do not use other than a specied projector.
Do not install a projector in a way other than specied.
Doing so may cause a fall accident, re, or electric shock.
Do not install the product in a place unable to withstand the weight or somewhere that is unsteady or
tilted.
Doing so may cause a failure or injury due to dropping, falling, etc.
Do not install the projector in a passageway.
Bumping into the projector or tripping on the power cord may cause a re, electric shock, or injury.
zWhen installing the projector in a passageway, take measures to prevent physical contact with the projector
by setting up a fence or similar things.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam.
Using the projector under such conditions will result in re, electric shocks.
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not block projector heat dissipation.
Heat accumulating inside the projector may cause a re.
zInstall the product so that the intake and exhaust of the projector will not be blocked.
Do not modify the oor stand.
Doing so may cause a malfunction due to falling, etc. or an electric shock or injury.
Do not use the supplied power cord with equipment other than a specied projector.
Using the supplied power cord with equipment other than a specied projector may cause electric shock or re
due to a short or heat generation.
Do not allow children to reach the supplied screws.
Accidentally swallowing them can cause physical harm.
zIf swallowed, seek medical advice immediately.
CAUTION
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric
shocks will result.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components of the projector to deteriorate, or result in re.
zTake particular care in locations exposed to direct sunlight or near heaters.

4 - ENGLISH
Read this rst! (continued)
CAUTION
This equipment is equipped with a three-pin grounding-type power plug.
Do not remove the grounding pin on the power plug. This plug will only t
a grounding-type power outlet. This is a safety feature. If you are unable
to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
 Panasonic assumes no responsibility for any accident or damage caused by improper
installation or incorrect handling.
Do not remove

ENGLISH - 5
Product composition
Check that the package contains the following parts. The number enclosed in < > is the quantity.
Floor stand <1> This stand is mounted to the projector to enable oor
standing installation.
There are rubber feet at three places on the bottom of
the stand.
The stand comes in two colors.
ET-JPF200BU: Black
ET-JPF200WU: White
Power cord
(K2CG3YY00183) <1>
This is connected to the <AC IN> socket of the optional
projector.
Screw with captive washer (M4×8) <4>
(ET-JPF200BU: XYN4+F8FJK)
(ET-JPF200WU: 4112055002)
These items secure the oor stand to the projector.
Attention
zAfter removing the product from the package, dispose of the power cord cap and packing material appropriately.
zDo not use the supplied power cord with equipment other than a specied projector.
zIf any part is missing, contact the dealer.
zStore small parts appropriately in a place out of the reach of infants and small children.
Note
zThe part numbers of the parts are subject to change without notice.
zThe illustrations of the product components, the projector or the assembling condition of the product and
projector, etc. may differ from the actual equipment.

6 - ENGLISH
Before mounting
■Use this product to install a compatible projector (not supplied) on the floor in a standing
position.
Compatible projectors: PT-JX200FBU / PT-JX200FWU
■A work bench and a soft cloth to prevent scratches are required when mounting this product
to a projector.
Prepare a bench for the mounting work with a height of at least 250 mm (9-27/32") and lay a soft cloth or the
like below the projector to prevent scratches.
246.4 mm
（9-11/16"）
Main unit
Power supply unit
Bench to adjust height
(If necessary, use plate or corrugated cardboard) Base
Soft cloth or alike
Workbench
(Table or box, etc.)
Soft cloth or alike
■For details such as the handling and operating procedures of the projector after this product
is mounted, refer to the operating instructions for the projector.
■Disposal
When disposing of this product, ask your local authority or dealer about the correct disposal method.

ENGLISH - 7
Mounting procedure
Main procedures
The main procedures up until installation of the projector are as follows.
For details on 1) to 3), refer to the corresponding reference pages.
1) Changing the orientation of the main unit of the projector (page 7)
2) Mounting the oor stand to the projector (page 8)
3) Connecting the power cord to the projector (page 10)
4) Installation
zInstall the projector while referring to “Projection dimensions” in the operating instructions for the projector.
Then adjust the orientation of the main unit as described in “Adjusting the projection position”.
zIf necessary, refer to “Attaching a security wire” (page 12) in this manual and take a measure to
protect the equipment against theft.
Changing the orientation of the main unit of the projector
This section describes changing the orientation of the main unit of the projector to make the mounting work easier
to do.
Ball joint fixing screw
Ball joint stopper
1) Place the projector on a cloth or the like that
has been laid on a at surface.
2) Loosen the ball joint xing screw.
zLoosen the ball joint xing screw of the
projector with the allen wrench (3/16ʺ across
ats) supplied with the projector.
Shaft holder
Main unit
3) Change the orientation of the main unit.
zLoosening the ball joint xing screw enables
rotation of the shaft holder so that the
orientation of the main unit can be changed.
4) Tighten the ball joint xing screw.
zTighten the ball joint xing screw with the allen
wrench (3/16ʺ across ats) supplied with the
projector to prevent the main unit moving during
the mounting work.
Attention
zWhen loosening the ball joint xing screw with the
pole being held by hand, take care to avoid the
hand(s) or ngers being pinched between the pole
and the main unit.

8 - ENGLISH
Mounting procedure (continued)
Mounting the oor stand to the projector
This section describes mounting the oor stand to the projector.
Main unit
Power supply unit
Bench to adjust height
Soft cloth or alike
Workbench
1) Place the projector on the work bench.
zPlace the power supply unit of the projector on
a work bench that has a soft cloth or the like
laid on it.
zAlso put the main unit of the projector on a
platform laid with a soft cloth or alike to make it
stable.
Attention
zThe projector might turn unstable in this case,
so at least two people are recommended to
perform the mounting work of the oor stand.
Rubber feet
2) Orient the oor stand to match the projector
orientation.
zPlace the oor stand so that the
rubber feet are facing upward and then orient it
to match the projector orientation.
3) Mount the oor stand to the projector.
zAlign the opening in the oor stand with the
position of the protrusion on the projector.
Protrusion
Opening

ENGLISH - 9
<AC IN> socket
Power supply unit
Tab
4) Slide the oor stand.
zSlide the oor stand so that the tab ts into
place into the <AC IN> socket side of the power
supply unit of the projector.
5) Secure the oor stand with the screws, captive
washers.
zFirmly secure the oor stand with the four
supplied screws with captive washers (M4 x 8).
Mounting procedure (continued)

10 - ENGLISH
Mounting procedure (continued)
Connecting the power cord to the projector
This section describes connecting the supplied power cord to the projector.
To prevent disconnection of the power cord, use the supplied power cord and rmly insert the connector
all the way into the <AC IN> socket of the projector and then secure it in place.
For details on the handling of the power cord, refer to “Read this rst!” (page 3).
■Power cord connection procedure
Connector
<AC IN> socket
1) Check the shapes of the <AC IN> socket of the
projector and the connector of the power cord
and then orient the connector correctly and
insert it rmly.
Guides
Connector secure
lock
Rib
Connector
Rib
Connector
secure lock
Power supply unit
2) Attach the connector secure lock.
zAttach the connector secure lock supplied with
the projector by sliding it along the guides on
both sides of the <AC IN> socket of the power
supply unit.
When attaching it, make sure that the connector
of the power cord ts further inside (power
supply unit) than the ribs on the connector
secure lock.

ENGLISH - 11
Mounting procedure (continued)
Tab
3) Close the connector secure lock.
zPush until the tab of the connector secure lock
clicks into place.
■Power cord disconnection procedure
1) Make sure that the projector is in the standby
state and then remove the power plug from the
power outlet.
Tab
2) Push down on the tab of the connector secure
lock to release it.
zTo release it when the projector is standing on
the oor, release the tab while lifting up the
power supply unit.
Guide
3) Remove the connector secure lock by sliding it
along the guides on the <AC IN> socket.
4) Pull out the connector of the power cord from
the <AC IN> socket.
zBe sure to press the power supply unit with one
hand, hold the power connector and pull it out
with another hand.

12 - ENGLISH
Attaching a security wire
If necessary, take a measure to protect the equipment against theft such as passing a commercially available
security wire between the pole and cable of the projector.
Pole
Security wire
(Commercially available product)
Cable
Mounting procedure (continued)

ENGLISH - 13
Specications
Dimensions
Width: 352 mm (13-7/8")
Height: 19.4 mm (3/4")
Depth: 438 mm (17-1/4")
Weight 1.7 kg(3.75 lbs.)
Outer color
ET-JPF200BU: Black
(for use in combination with PT-JX200FBU)
ET-JPF200WU: White
(for use in combination with PT-JX200FWU)
Power cord length 2.0 m (78-3/4")
External dimension diagram
Unit: mm
438.0 (17-1/4")
5.7 (1/4")
19.4 (3/4")
φ352.0 (13-7/8")

14 - ENGLISH
Assembly dimension diagram
These dimensions are when this product is mounted to a separately sold projector (product number:
PT-JX200FBU / PT-JX200FWU).
Unit: mm
152.4 (6")
278.8 (11")
438.0 (17-1/4")
149.2 (5-7/8")
264.8 (10-7/16")
227.6 (9")
312.6 (12-5/16")
142.6 (5-5/8")
66.2 (2-5/8")
5.7 (1/4")
128.0 (5-1/16")
φ170.0 (6-11/16")
φ352.0 (13-7/8")
Ball joint movable
range: approx. 90°
Main unit
The main unit can rotate 360°
Specications (continued)

ENGLISH - 15
MEMO

W1216JG0 -ST
Panasonic Corporation
Web Site: http://panasonic.net/avc/projector/
© Panasonic Corporation 2017
Panasonic Systems Communications Company of North America
5th Floor, Two Riverfront Plaza, Newark, NJ 07102-5490
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
TEL: (877) 803 - 8492
TEL: (905) 624 - 5010
Panasonic Canada Inc.