Panasonic WV-SPN531A User manual

Network Camera
Model No. WV-SPN531A / WV-SPN311A /
WV-SPN310A
* This illustration represents WV-SPN311A
(Please purchase the recommended lens separately.)
● This manual describes the installation procedures, cable connections, and the angle of view
adjustment of this product.
● Before reading this manual, be sure to read the Important Information.
● This manual describes how to install the network camera using model WV-SPN311A as an example.
sL0915-1105 PGQX1973YA Printed in China
Standard accessories
Important Information ............................... 1 pc.
Installation Guide (this document) ............ 1 set
Warranty card ........................................... 1 set
CD-ROM*1 ................................................ 1 pc.
Code label*2 .............................................. 1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2
This label may be required for network management. The network administrator shall retain the code label.
Parts and functions
*1 The detailed specications on the right describe terminals with markings.
*2 SDXC/SDHC/SD memory card is described as SD memory card.
Making connections
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
Before starting the installation, check the entire system configuration. The following illustration
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
<Required cable>
Ethernet cable (category 5e or better, straight)
Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.
*1 Recommended cable length from the speaker : less than 10 m {32.8 feet}
Recommended cable length from the microphone : less than 1 m {3.28 feet}
When connecting to a network using a PoE hub
ø9 mm
{11/32 inches}
Example of audio cable connector
9 mm
{11/32 inches}
13 mm {1/2 inches}
Example of Ethernet cable connector
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turning
off the power of the audio output devices. Otherwise, loud noise may be heard from
the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conversion
cable (mono-stereo).
Connect an external amplifier-embedded speaker to the audio output cable
SPN531 SPN311
Connect a stereo mini plug (ø3.5 mm).
● Output impedance : Approx. 600 Ω (unbalanced)
● Recommended cable length : Less than 10 m {32.8 feet}
● Output level : –20 dBV
Microphone/line input cable SPN531 SPN311
Connect a stereo mini plug (ø3.5 mm).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
Less than 10 m {32.8 feet} (for line input)
● Recommended microphone: Plug-in power type (option) ●Supply voltage: 2.5 V ±0.5 V
● Input level for the line input: Approx. –10 dBV
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
IMPORTANT:
● Use all 4 pairs (8 pins) of the Ethernet cable.
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power
supply, 12 V DC will be used for power supply.*
* If a 12 V DC power supply and a PoE hub or router are used at the same time,
network connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you disconnect 12 V DC while 12 V DC
power supply and a PoE hub or router are used at the same time, the power supply
may stop, causing the camera to restart.
● When the Ethernet cable is disconnected once, reconnect the cable after around
2 seconds. When the cable is quickly reconnected, the power may not be supplied
from the PoE device.
IMPORTANT:
● Do not connect 2 wires or more directly to a terminal. When it is necessary to con-
nect 2 or more wires, use a splitter.
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by con-
figuring the setting. Refer to the Operating Instructions on the provided CD-ROM
for further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings
("Off", "Alarm input", "Alarm output" or "AUX output").
● Install external devices so that they do not exceed the rating of the network camera.
● When using the EXT I/O terminals as the output terminals, ensure they do not
cause signal collision with external signals.
IMPORTANT:
● The adjustment monitor is used for checking the adjustment of the angular field of
view when installing the camera or when servicing. It is not provided for recording/
monitoring use.
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not
be displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
Connect an Ethernet cable (category 5e or better, straight)
Connect the alarm input/output cable
Connect an Ethernet cable (category 5e or better, straight) to the network connector.
Connect the cables of external devices to the EXT I/O terminal plug.
q When connecting an external device, remove 8 mm - 9 mm of the outer jacket of the cable
and twist the cable core to prevent the short circuit first.
Specification of cable (wire): AWG 20 - AWG 26, Single core, twisted
w Push down the button of the desired terminal on the external I/O terminal plug with a ball-
point pen, and release the button when the cable of the external device is fully inserted
into the terminal hole.
PoE device (hub)
PC
Ethernet cable
(category 5e
or better, straight)
Adjustment monitor
Adjustment monitor
Ethernet cable
(category 5e or better, straight)
Ethernet cable
(category 5e or better, straight)
Powered speaker
Microphone
Powered speaker
Microphone
Recommended total extended
cable length*1
Note:
● Check whether the stripped part of the wire is not exposed and is securely connected.
<Ratings>
● ALARM IN1 (DAY/NIGHT IN SPN531 SPN311 , Auto time adjustment), ALARM IN2, ALARM IN3
Input specication : No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF : Open or 4 V - 5 V DC
ON : Make contact with GND (required drive current: 1 mA or more)
● ALARM OUT, AUX OUT
Output specication : Open collector output (maximum applied voltage: 20 V DC)
ON : 4 V - 5 V DC by internal pull-up
OFF : Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is "Off".
1 2 3 4
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
[phone]
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Installation Guide
Included Installation Instructions
Panasonic System Networks Co., Ltd. 2015
*1 12 V DC power supply terminal
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
● When data is being sent via the network camera Blinks green (accessing)
● When the camera is able to communicate with Lights orange
the connected device
ACT indicator
LINK indicator
A Tripod mount base ............................... 1 pc.
B Power cable plug ................................. 1 pc.
C
Safety wire lug ...................................... 1 pc.
D Wire lug fixing screws
(M2.5 × 8 mm {5/16 inches}) ............. 2 pcs.
(of them, 1 for spare)
E Safety wire ........................................... 1 pc.
F Washer ................................................. 1 pc.
G Spring washer ...................................... 1 pc.
−+
B
IMPORTANT:
● The 12 V DC power supply shall be insulated from the commercial AC power.
● Be sure to use the power cable plug (B: accessory) provided with this product.
● Be sure to fully insert the power cable plug (B: accessory) into the 12 V DC power
supply terminal. Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the
power cable.
● Be sure to use an AC adaptor compliant with the Specifications (written in the
indication label on the bottom side of this unit) regarding power source and power
consumption.
Caution:
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED
TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or
LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Connect the power cable
Connect the output cable of the DC power supply to the power cable plug (B: accessory).
q Loosen the screw of the power cable plug (B: accessory), strip 3 mm to 7 mm {1/8 inches
to 9/32 inches} from the end of the wire, twist the stripped part of the wire sufficiently to
avoid short circuit, and then connect the output cable to the power cable plug
(B: accessory).
w Tighten the screw of the power cable plug (B: accessory). (Recommended tightening
torque: 0.34 N·m {0.25 lbf·ft})
Note:
● Check whether the stripped part of the wire is not exposed and is securely
connected.
● When connecting an external power supply to the camera, use the AWG 16 to
AWG 24 single-wired or stranded wired cables.
ALARM IN1, DAY/NIGHT IN
SPN531 SPN311
, Auto time adjustment
(Alarm input terminal 1, DAY/NIGHT input terminal
SPN531 SPN311 , Auto time adjustment terminal)
ALARM IN2, ALARM OUT
(Alarm input terminal 2, Alarm output terminal)
ALARM IN3, AUX OUT
(Alarm input terminal 3, AUX output terminal)
GND
External I/O terminal plug
button
SD ON/OFF button
q When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights
up in green and data can be saved to the SD memory card.
w When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights
off and the SD memory card can be removed.
SPN311
SPN531
SPN311
SPN531
SPN311
SPN531
SPN311
SPN531
*1 Network connector RJ45
*1 Microphone/line input connector
MONITOR OUT terminal
(factory shipment: NTSC monitor) *1 Audio output connector
*1 EXT I/O terminals
● When ABF (Auto Back Focus) operation is being Blinks red (Interval of 1 time/ second)
executed SPN531 SPN311
● When the focus assist function is activated SPN310 Blinks red (1 time)
● When the focus ring is positioned near the best Lights red
focus position SPN310
● When the set is being started Lights red
● When an SD memory card is recognized normally Lights red → Lights off
● When the SD card slot is not used or an abnormality is Lights red → Stays red
detected in SD card after the camera has started
SD ERROR/ABF indicator SPN531 SPN311 SD ERROR/F.A. indicator SPN310
● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to
switch the output signal of the MONITOR OUT terminal (NTSC⇔PAL output), the MONITOR
OUT terminal can be switched for the NTSC monitor/PAL monitor.
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be
initialized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol
will not be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
● How to initialize the camera
Follow the steps below to initialize the network camera.
q Turn off the power of the camera. When using a PoE hub, disconnect the Ethernet cable
from the camera. When using an external power supply, disconnect the power cable plug
(B: accessory) from the 12 V DC power supply terminal.
w Turn on the power of the camera while holding down the INITIAL SET button, and keep
the INITIAL SET button held down till the SD MOUNT indicator is lit in green (more than 10
seconds). In about 2 minutes after releasing the INITIAL SET button, the camera will start
up and the settings including the network settings will be initialized.
INITIAL SET button (Initializing / NTSC ⇔ PAL switch button)
The following parts are used during installation procedures.
*1 Depending on the scanning ap-
plication used, the Data Matrix
may not be able to be read
correctly. In this case, access
the site by directly entering the
following URL. http://security.
panasonic.com/pss/security/
support/qr_sp_select.html
Data Matrix: To our
website*1
Built-in MIC SPN310
Slide cover
ALC lens connector Lens (recommended)
(WV-SPN531A and WV-SPN311A are not equipped with Built-in MIC function.)
SD slot (SD)
Focus assist (F.A.) SPN310
● When an SD memory card*2 is inserted and could Lights off → Blinks green →
be recognized Lights off
● When data can be saved after the SD memory card is Lights off → Lights green
inserted and the SD ON/OFF button is pressed
(less than 1 second)
● When data can be saved to the SD memory card Lights green
● When the SD memory card is removed after holding down Lights green → Blinks green →
the SD ON/OFF button (about 2 seconds) Lights off (recording)
Lights green → Lights off
(waiting for recording)
● When data cannot be saved to the SD memory card Lights off
because an abnormality was detected or the SD
memory card is configured not to be used
Note:
● Lighting/blinking LED can be turned off with the software settings at any time. (The initial
state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the
installation conditions. (☞ Operating instructions included in the CD-ROM)
SD MOUNT indicator
Auto back focus button (ABF) SPN531 SPN311
SPN531
SPN531
SPN311
SPN311

lens cable
ALC lens connector
Focus ring
Zoom lock knob
T
Lens
(recommended)
Lens mounting hole
[2] Secure the wall mount bracket (locally
procured) using separately procured
screws or anchors.
[3] Loosen the camera mount bracket xing
mechanism to freely move the camera
mount bracket.
Align the screw thread with the xing
screw hole of the camera, and rotate
the camera mount bracket to secure
the camera. Tighten the camera mount
bracket xing mechanism and secure
the camera mount bracket.
* The tripod mount base (A: accessory)
is not used.
[4] Attach the safety wire (E: accessory) to the
foundation area of the architecture or where
sufcient strength is assured. Prepare the
xing screws according to the material of the
area where the safety wire
(E: accessory) is
to be installed.
Protruded portion from
mount face: ø20 mm
{25/32 inches} or less
Protruded portion from ange face:
4.5 mm {5/32 inches} or less
Installation
The installation tasks are explained using 5 steps.
Step1
Preparations
Step2
Mount the lens to the cam-
era.
Step3
Insert/remove an SD memory
card.
Step4
Mount the camera.

Step1 Preparations
To install the camera to a ceiling or wall, prepare the required mount bracket and the screws that
secure the bracket, or the anchor bolt for each installation method before starting the installation.
The following are requirement examples for the various installation methods.
Installation method Recommended screw
Minimum pull-out
strength
(per 1 pc.)
[1] For mounting on ceiling*1
(Mount bracket: approx. 260 g {0.57 lbs},
camera: 350 g {0.77 lbs} SPN531 SPN311 ,
325 g {0.72 lbs} SPN310 , lens: 40 g
{0.09 lbs})
M6 or M8 screws × 4*1 562 N {126 lbf}*2
M4 × 1 (for the safety wire) 24.5 N {5.5 lbf}
[2] For mounting on wall*1
(Mount bracket: approx. 420 g {0.93 lbs},
camera: 350 g {0.77 lbs} SPN531 SPN311 ,
325 g {0.72 lbs} SPN310 , lens: 40 g
{0.09 lbs})
M6 or M8 screws × 4*1 724 N {163 lbf}*2
M4 × 1 (for the safety wire) 24.5 N {5.5 lbf}
[3] When using the tripod mount
base (A: accessory)*3 — —
*1 The number of required screws or anchor bolts varies depending on the specications
of the mount bracket (locally procured). Refer to the operating instructions of the mount
bracket (locally procured) for information about how to mount the mount bracket.
*2 Make sure that the screws or anchor bolts separately procured when locally procuring a
mount bracket for the ceiling or wall are capable of supporting the total weight (including
the moment force when mounting to a wall).
*3 Size of the bracket mounting hole: "1/4-20UNC camera tripod mounting hole (depth 9 mm
{11/32 inches})"
IMPORTANT:
●
The installation area shall be strong enough to hold the camera and camera mount bracket.
●
The camera mount bracket (locally procured) shall be mounted on the foundation part of
the construction or a part with adequate strength.
● Select screws according to the material of the ceiling that the camera will be mounted
to. In this case, wood screws and nails should not be used.
● If a ceiling board such as plaster board is too weak to support the total weight, the
area shall be sufficiently reinforced.
Step5
Connect and adjust the
camera
 
The lens section is not included with the camera. It is possible to mount a 1/3 type
video camera lens to the camera. It is recommended to use a recommended high-
resolution lens especially when the illuminance level of the photographic subject is
low and the camera is used with the lens iris open. If a lens other than the recom-
mended lens below is mounted and the camera is used at a resolution of 1280 × 720
or higher, the camera cannot achieve full performance of high resolution.
Refer to our website (http://security.panasonic.com/pss/security/support/info.html) for
further information about the recommended lens.
* When using a lens made by other companies, use a lens that has a protruded por-
tion from the mount face of ø20 mm {25/32 inches} or less and a protruded portion
from the ange face of 4.5 mm {5/32 inches} or less. Lenses without a focus adjust-
ment mechanism and zoom lenses cannot be used.
q Remove the cover lm attached to the
lens mounting hole of the camera.
w Slowly rotate the lens clockwise to
mount the lens and connect the lens
cable to the ALC lens connector of the
camera.
1 3
2 4
ALC lens connector
Step2 Mount the lens to the camera
When using an SD memory card, go through the following procedure before installing
the camera. When removing an SD memory card, reverse the procedure.
Refer to the Operating Instructions on the provided CD-ROM for further information
about the SD memory card settings.
[1] Open the slide cover on the side of the camera, insert an SD memory card fully into
the SD memory card slot until a click is heard.
● Insert the SD memory card with its label facing up.
[2] Close the slide cover on the side of the camera.
● To remove the SD memory card, hold down the SD ON/OFF button for about
2 seconds. When the flashing SD MOUNT indicator goes out, you can remove
the SD memory card.
● After the SD memory card has been replaced, press the SD ON/OFF button,
and make sure the SD MOUNT indicator is continually lit.
● If you do not press the SD ON/OFF button after replacing the SD memory
card, the SD MOUNT indicator is continually lit approximately 5 minutes later.
Connect the safety wire (E: accessory)
● When securing the camera using a separately procured bracket, use the xing screw
(M4, locally procured), and the safety wire (E) , washer (F) , and spring washer (G)
(accessories).
[1] Engage the safety wire (E: accessory) with the wire engaging hole.
[2] Secure the safety wire lug
(C: accessory) to the camera
mount screw hole with the wire
lug xing screw (D: accessory).
(Recommended tightening
torque: 0.39 N·m {0.29 lbf·ft})
 When using the tripod mount
base (A: accessory)
● Use the tripod mount base (A: accessory)
when mounting the camera to raise the
camera mounting position.
[1] Secure the tripod mount base
(A: accessory) to the bottom side
of the camera using 2 xing screws.
(Recommended tightening torque:
0.39 N·m {0.29 lbf·ft})
Size of the mounting hole: "1/4-20UNC
camera tripod mounting hole
(depth 9 mm {11/32 inches})"
SD memory card
* Label face upward
Wire engaging hole
After mounting
Part A
Safety wire lug
(C: accessory)
q Pass part A through the wire
engaging hole
Fixing screws
1/4-20UNC camera tripod
mounting hole (depth 9 mm
{11/32 inches})
* The wire image mounted to the safety wire lug in
[1] of "Connect the safety wire" is not shown.
* The wire image mounted to the safety wire lug in
[1] of "Connect the safety wire" is not shown.
Wire lug xing screw
(D: accessory)
Fixing screw hole
Step3 Insert/remove an SD memory card Step4 Mount the camera Step5 Connect and adjust the camera (Continued)
Step5 Connect and adjust the camera
Note:
● The most common use of a varifocal lens and a zoom lens
Note that the adjustment method is different depending on the type. For fur-
ther information, refer to the operating instructions for the lens to be used.
When using 8x or 10x lens, adjust the back focus after positioning the
zoom ring at the "W" end and positioning the focus ring at a step short of
the "F" end. SPN531 SPN311
When using 2x or 3x lens, adjust the back focus after positioning the
zoom ring at the "T" end and positioning the focus ring at a step short of
the "F" end. SPN531 SPN311
● Depending on the lens to be used, if the zoom ring is fully rotated in the
"W" direction, the periphery may become dark. In such a case, rotate the
zoom ring in the "T" direction for readjustment.
● When images in the near-infrared light area change from the color mode
to the black & white mode, out-of-focus may be occurred according to the
nature of optical property. In this case, the focus can be corrected by
selecting "Auto" or "Preset" for "Adjusting method" on the setup menu
(The focus will not automatically be adjusted according to the illumination
level change once the focus is corrected.) Refer to the Operating
Instructions (included in the CD-ROM) for how to configure the "Adjusting
method" setting on the setup menu. SPN531 SPN311
● When shooting the following subjects, it may have difficulty adjusting the
back focus position automatically. In this case, adjust the back focus
position manually from the setup menu. Refer to the Operating
Instructions (included in the CD-ROM) for how to perform the auto back
focus function from the setup menu. SPN531 SPN311
● When shooting the following subjects or in the following places, close the
"FOCUS ADJUSTMENT" menu by pressing the focus assist (F.A.) but-
ton, and adjust the focus to obtain the best focus position while monitor-
ing images from the camera. SPN310
● Subj. moves frequently
● Subj. with large illuminance change
● Subj. with low illuminance
● Subj. through a window
● Subj. with less contrast such as white wall
● Subj. with heavy flicker
● "BEST FOCUS" display may generate misjudgment according to shooting
environment. Misjudgment can be lessened by switching camera mode to
30 fps mode (SD OFF). Refer to the Operating Instructions (included in the
CD-ROM) for switching methods of camera mode. SPN310
● In case the angular field of view has changed during adjustment, close
the "FOCUS ADJUSTMENT" menu by pressing the focus assist (F.A.)
button. (When the angular field of view changes, the indicator values of
"PEAK HOLD" and "INDICATOR" also change.) After fixing the angular
field of view, open the "FOCUS ADJUSTMENT" menu by pressing the
focus assist (F.A.) button, then adjust the focus again. SPN310
IMPORTANT:
● Be sure to rotate and secure the camera mount bracket. Rotating the camera
places a large burden on the camera mount bracket, and may cause damage.
● Attach the safety wire (E: accessory)
in a position higher than the camera and the mount bracket.
● Attach the safety wire (E: accessory) so that if the camera were to become
detached, it would not fall on nearby people.
IMPORTANT:
● Mount the bracket in a position higher than 2.7 m {8.86 feet} from the floor.
IMPORTANT:
● Be sure to rotate and secure the camera mount
bracket. Rotating the camera places a large
burden on the camera mount bracket, and may
cause damage.
● The safety wire (E: accessory) shall be adjusted to
remove slack.
● The distance from the camera to the ceiling
changes depending on the tilt angle of the
camera. Attach the safety wire (E: accessory) in a
position according to the tilt angle of the camera.
For mounting on ceiling
[1] Mark the position of holes to be made for the ceiling mount bracket (locally procured) on
the attachment position of the ceiling, and make those holes for attachment.
Determine the hole diameter and hole depth according to the specications of the screws
or anchor bolts to be used.
 For mounting on wall
[1] Mark the position of holes to be made for the wall mount bracket (locally procured) on the
attachment position of the wall, and make those holes for attachment.
Determine the hole diameter and hole depth according to the specications of the screws
or anchor bolts to be used.
[2] Secure the ceiling mount bracket
(locally procured) using separately
procured attachment xing screws or
anchors.
[3] Loosen the camera mount bracket xing
mechanism to freely move the camera
mount bracket.
Align the screw thread with the xing
screw hole of the camera, and rotate
the camera mount bracket to secure
the camera.
Tighten the camera mount bracket
xing mechanism and secure the
camera mount bracket.
* The tripod mount base (A: accessory) is not used.
[4] Attach the safety wire (E: accessory) to the
foundation area of the architecture or where
sufcient strength is assured. Prepare the xing
screws according to the material of the area where
the safety wire (E: accessory) is to be installed.
If the camera angle is changed when the camera mount
bracket xing mechanism is tightened, excessive force
is applied to the camera mount bracket and camera,
which may damage them.
After adjusting the camera angle, make sure to tighten the
camera mount bracket xing mechanism securely again.
[1] Connecting wires
Connect the necessary cables/lead wires according to the procedure of "Making
connections". (When power is supplied by PoE, the camera is turned on when an
Ethernet cable is connected. Make sure to connect the Ethernet cable after turning
off the power of hub and router.)
[2] Adjusting the camera angle
Connect the adjustment monitor to the MONITOR OUT terminal of the camera
with the RCA pin cable (locally procured).
Loosen the camera mount bracket xing mechanism on the camera mount bracket,
and then check the adjustment monitor to adjust the camera angle.
When adjusting the camera angle, make sure to loosen the camera mount bracket
xing mechanism on the camera mount bracket before making adjustments.
[3] Adjusting the focus SPN531 SPN311
q First, reset the back focus position by holding down
the auto back focus button for 5 seconds or more
when the power is on. (This operation can also be
performed on the setup menu. Refer to the Operating
Instructions (included in the CD-ROM).) SPN531 SPN311
w Manually adjust the angle of view and focus coarsely by adjusting the zoom and
focus of the lens, and then press the auto back focus button on the side of the
camera (page 1) or perform the auto back focus function from the setup menu.
SPN531 SPN311
Refer to the Operating Instructions (included in the CD-ROM) for how to perform
the auto back focus function from the setup menu.
* How to take a wide depth of field: When focus is desired on entire near or
distant subjects, select indoor scene mode, or adjust the focus to the midrange
position using manual focus adjustment.
Adjusting the focus SPN310
The focus is adjusted using the focus assist function.
The angle of view and focus can be adjusted in accordance with the distance between
the camera lens and a photographic subject. These adjustments shall be performed
together with the camera angle adjustment.
q Loosen the zoom lock knob, and adjust the angle of view
(angular eld of view) in accordance with the photographic
subject by moving the zoom lock knob and focus ring.
Note:
●
The focus may not be adjusted appropriately when the
zoom lock knob is positioned at the "W" (or "T") end.
In this case, adjust the focus again by slightly moving
the zoom lock knob to the direction of "T" (or "W").
w Fasten the zoom lock knob.
e Press the focus assist button.
→ "FOCUS ADJUSTMENT" menu will be displayed.
The focus assist function will be activated to perform the optimum adjustment.
r When the focus ring is positioned near the best focus position, the position will
automatically be memorized as the "PEAK HOLD" position.
t Loosen the focus lock knob and move the focus ring, the current focus position will
be indicated on "INDICATOR". Adjust the focus position so that the indicator value
goes close to the "PEAK HOLD" position.
y When the indicator value goes to the best focus position, "BEST FOCUS" will be
displayed at the lower right corner of the screen, then fasten the focus lock knob.
u Press the focus assist button again to close the "FOCUS ADJUSTMENT" menu.
(No operation for 3 seconds also closes the menu.)
IMPORTANT:
● After performing basic adjustments, make sure to press the auto back focus
button once to perform detailed adjustments. SPN531 SPN311
Step4 Mount the camera (Continued)
Washer
(F: accessory)
Spring washer
(G: accessory)
Recommended screw M4
Minimum pull-out strength
24.5 N {5.5 lbf}
Safety wire
(E: accessory)
Ceiling
Pin No.
1 Dump
2 Dump
3 Drive
4 Drive
Safety wire
(E: accessory)
Recommended screw M4
Minimum pull-out strength 24.5 N {5.5 lbf}
Washer (F: accessory)
Spring washer (G: accessory)
Foundation part of
construction or part
with adequate strength
Wall
●After connecting the camera, refer to "Configure the settings of the cam-
era" (leaflet) and perform the camera settings.
Tripod mount base
(A: accessory)
Fixing screws
Wall mount bracket
(example)
Attachment xing
screws
M6 or M8 × 4
(locally procured)
Camera mount bracket
fixing mechanism
Camera mount
bracket
w Pass part A through the
other loop of the wire
FOCUS ADJUSTMENT
LOW HIGH
............|.......
INDICATOR 620 BEST
PEAK HOLD 635 FOCUS
W
N
F
Ceiling mount
bracket (example)
Attachment xing
screws M6 or M8 × 4
(locally procured)
Camera mount
bracket
Camera mount brack-
et xing mechanism
Recommended
screw M4
Minimum pull-out
strength
24.5 N {5.5 lbf}
Safety wire (E: accessory)
Safety wire lug
(C: accessory)
Attachment xing
screws M4 × 1
(locally procured)
Higher than the
camera and wall
mount bracket.