Panasonic WVCW474F - COLOR CCTV CAMERA User manual

■Preface
Panasonic's WV-CW474F/CW474S series color digital camera is designed for installing a
wall or ceiling board.
■Installation
The following installation should be made by qualified service personnel or system installers.
Important notice: Be sure to use a ceiling board having enough strength to support this
camera.
■Camera Mounting Position
WV-CW474F should be mounted into the two gang junction box (4 in. x 4 in.) built in a
wall or ceiling.
WV-CW474S should be mounted by use of the supplied camera mounting bracket. The
camera mounting bracket can be mounted on a flat surface such as a wall and ceiling.
Secure the camera mounting bracket to the position where the camera should be mounted
with the supplied four screws. Verify the camera mounting bracket is mounted firmly after
screwing it.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The exclamation point within
an equilateral triangle is intend-
ed to alert the user to the pres-
ence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The lightning flash with arrow-
head symbol, within an equilat-
eral triangle, is intended to
alert the user to the presence
of uninsulated "dangerous volt-
age" within the product's enclo-
sure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons. The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
SA 1966
SA 1965
N1101-1121 V8QA5952BN Printed in Japan
N19
Color CCTV Cameras
Instructions
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TOREDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interfer-
ence when the equipment is operated in a
commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency
energy and, if not installed and used in accor-
dance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.
FCC Caution: To assure continued compli-
ance, (example - use only shielded interface
cables when connecting to computer or
peripheral devices). Any changes or modifica-
tions not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.
For U.S.A
Model No. WV-CW474F
WV-CW474S
85 mm
(3-3/8")
<Mounting hole pattern>
85 mm
(3-3/8")
Cable access hole for
3/4" pipe
Bracket center
51 mm
(2")
Camera mounting bracket
screw x 4 (procured locally)

2. Unscrew the red screw for
transport protection with a
Phillips screw driver.
3. Connect the power cable and the
BNC plug of the video output
cable as described in the section
"CONNECTIONS".
Loosen three
screws.
Insulate the three connecting leads of the power cords from one another, and cover the
connecting portions with insulating tape as well as the portions between the video out-
put cable and the BNC connector and between the BNC connectors to prevent the por-
tions from water immersion.
■How to mount the camera
1. Remove the dome cover from the
main body by loosening the three
dome cover mounting screws.
The dome cover is fixed with tamperproof
screws.
Loosen the three dome cover mounting
screws by using the supplied bit for tam-
perproof screw.
Shown figure is an example for junction box.
Camera mounting screw x 4 (supplied)
Seal the screws and screw holes with such a material as silicone
clay (rubber) to prevent water immersion if the camera is installed
in the outdoor.
46 mm
(1-13/16")
83.5 mm
(3-5/16")
4. Secure the camera with four camera mounting screws.
•For WV-CW474F
Secure the camera on the junction box with four camera mounting screws.
The four camera mounting screws are not supplied. Please take note that you should
purchase the screws in accordance with the tapped holes of the junction box.
The mounting holes of this unit accept M4 or less screws.
Camera mounting screw x 4
(procured locally)
Loosen the dome
cover mounting
screw x3
• The camera mounting bracket is not designed for waterproof.
Insulate the three connecting leads of the power cords from one another, and cover the
connecting portions with insulating tape as well as the portions between the video out-
put cable and the BNC connector and between the BNC connectors to prevent the por-
tions from water immersion.
•For WV-CW474S
Secure the camera on the camera mounting bracket mounted on a wall or ceiling.
Power cord
Video output cable
Power cord
Video output cable

(1) Loosen the pan lock screw (stain-
less) with the Phillips screwdriver.
Panning becomes adjustable.
(2) Loosen the tilting lock screw
(stainless) with the Phillips screw-
driver.
Tilting becomes adjustable.
Note: Do not touch a black screw
placed on the opposite side.
(3) After adjusting panning and tilting,
tighten both of the lock screws
with the Phillips screwdriver.
(4) Adjust the azimuth.
If the image is slanting, turn the azimuth adjuster to obtain a leveled image.
6. Adjust the focus.
Precautions:
• The focus adjustment should be done at the same time as the camera angle adjust-
ment.
• Set the zoom position to TELE before focusing.
(1) Loosen the focus lock screw by turning it counterclockwise.
The focus lock screw and the tip of the focus lever are identical with each other. The
focus lever becomes movable after loosening the focus lock screw.
(2) Adjust the focus by moving the focus lever to NEAR side or FAR side.
(3) Turn the focus lock screw clockwise to tighten the focus lever after adjustment.
7. Adjust the zoom.
(1) Loosen the zoom lock screw by turning it counterclockwise.
The zoom lock screw and the tip of the zoom lever are identical with each other.
The zoom lever becomes movable after loosening the zoom lock screw.
(2) Adjust the zoom by moving the zoom lever to TELE side or WIDE side.
(3) Turn the zoom lock screw clockwise to tighten the zoom lever after adjustment.
8. Reinstall the dome cover to the
main body by tightening three
dome cover mounting screws.
Azimuth adjuster
TELE
Zoom lock screw
Focus lock screw
FAR
NEAR
WIDE
Tighten the dome
cover mounting
screw x3
5. Adjust the panning, tilting and azimuth while watching the monitor.
Notes:
• You can check images by connecting an LCD monitor and such devices to the
monitor output jack.
However, images are not avail-
able on the monitor connected
to the video output cable.
• When connecting the LCD
monitor's plug to the monitor
output jack, the mode is auto-
matically set to ELC.
When disconnecting it, ELC
mode is automatically can-
celed.
• The signal from the monitor out-
put jack can cause smear on
the monitor when a high-lumi-
nance area is displayed.
Pan lock screw
(stainless)
Tilting lock screw (stainless)
Panning table
Variable angles
plus or minus 75 °(max.)

2001 © Matsushita Communication Industrial Co., Ltd.
Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 [phone]
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 [phone]
Midwest: 1707 North Randall Road, Elgin, IL 60123 [phone]
Western: 6550 Katella Ave., Cypress, CA 90630 [phone]
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada [phone]
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 [phone]
■Connections
Precaution:
The following connections should be made by qualified service personnel or system
installers in accordance with NEC 725-51.
Note: For the WV-CW474F/CW474S Color CCTV Cameras, do not use a transformer larger
than 10 VA.
1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry
seal until it has been ascertained that the unit is functioning.
CONNECT THIS TO 24V AC CLASS 2 POWER SUPPLY ONLY.
2. To prevent fire or electric shock hazard, the UL listed wire VW-1 style 1007 should
be used for the cable for 24V AC Input Terminals.
CAUTIONS
• Power supply connection
Recommended wire gauge sizes for 24 V AC line.
#24
(0.22mm2)
Copper wire size
(AWG)
Length of cable
(Approx.) (m)
(ft)
#22
(0.33mm2)#20
(0.52mm2)#18 (0.83mm2)
20 30 45 75
65 100 160 260
24 V AC
Video Output Cable
To Video IN
(CAMERA IN)
BNC Plug
Green (Ground)
White (Neutral)
Black (Live)
BNC Plug
BNC Plug
■Specifications
Dimensions: WV-CW474F: 133 mm (H) x 152.5 mm (D)
5-1/4” (H) x 6” (D)
WV-CW474S: 136.5 mm (H) x 160 mm (D)
5-3/8” (H) x 6-5/16” (D)
Weights: WV-CW474F: 1.0 kg(2.2 lbs.)
WV-CW474S: 1.4 kg(3.1 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
■Standard Accessories
Tamperproof screw bit ...................................................................... 1 pc.
Camera mounting bracket (supplied with only WV-CW474S)............ 1 pc.
Camera mounting screw (with a plastic washer) .............................. 4 pcs.
(supplied with only WV-CW474S)