Panasonic SB-MAX700PH User manual

© Panasonic Corporation 2013, All rights reserved.
Unauthorized copying and distribution is a violation of
law.
PSG1301011CE
Speaker System
Model No. SB-MAX700PH
SB-MAX700GS
Product Color : (K)... Black Type
TABLE OF CONTENTS PAGE PAGE
1 Service Navigation----------------------------------------------- 2
1.1. Speaker System Information (SB-
MAX700PHK)----------------------------------------------- 2
1.2. Speakers Setup-------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Disassembly and Assembly Instructions ---------------- 4
3.1. Disassembly of Upper Front Panel Assembly------ 5
3.2. Disassembly of Tweeter Speaker (SP1)------------- 7
3.3. Disassembly of Full Range Speaker (SP4) --------- 7
3.4. Disassembly of Full Range Speaker (SP3) --------- 8
3.5. Disassembly of Lower Front Panel Assembly------ 9
3.6. Disassembly of Woofer Speaker (SP2)-------------11
3.7. Disassembly of Lighting Wire P.C.B.
Assembly ---------------------------------------------------12
3.8. Replacement of Speaker Connector Housing
(For SB-MAX700PHK) ---------------------------------14
3.9. Replacement of Speaker Connector Housing
(For SB-MAX700PHK) ---------------------------------15
4 Wiring Connection Diagram ---------------------------------16
4.1. Front Speakers (SB-MAX700PHK) ------------------16
5 Exploded View and Replacement Parts List -----------17
5.1. Front Speakers (SB-MAX700PHK) Cabinet
Parts Location -------------------------------------------- 17
5.2. Packaging-------------------------------------------------- 18
5.3. Replacement Parts List--------------------------------- 19

2
1 Service Navigation
1.1. Speaker System Information (SB-MAX700PHK)
SB-MAX700PHK is use for the following models:
SC-MAX700PHK
SB-MAX700GSK is use for the following models:
SC-MAX700GSK
1.2. Speakers Setup

3
2 Specifications
Front Speakers
Type 4 way, 4 speaker system (Bass reflex)
Speaker(s)
Super Woofer (Low) 38 cm cone type
Super Woofer (Medium Low) 20 cm cone type
Woofer 10 cm cone type
Tweeter 6 cm cone type
Impedance 3 Ω(High), 3 Ω(Medium Low),
2 Ω(Low)
Output sound pressure 88 dB/W (1 m)
Frequency range 38 Hz to 23 kHz (-16 dB)
44 Hz to 18 kHz (-10 dB)
Dimensions (W x H x D) 558 mm x 796 mm x 525 mm
Mass (Weight) 31.0 kg
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum ana-
lyzer.

4
3 Disassembly and Assembly Instructions
Caution Note:
• This section describes procedures for checking the operation and replacing the main components.
• For reassembly after operation checks or replacement, reverse the respective procedures.
• Special reassembly procedures are described only when required.
• Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
• During the disassembly and/or assembly process, please handle with care as there may be chassis components with sharp
edges.
• During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the service man-
ual.
• Select items from the following indexes when disassembly or replacement are required.
Front Speakers (SB-MAX700PHK)
• Disassembly of Upper Front Panel Assembly
• Disassembly of Tweeter Speaker (SP1)
• Disassembly of Full Range Speaker (SP4)
• Disassembly of Full Range Speaker (SP3)
• Disassembly of Lower Front Panel Assembly
• Disassembly of Woofer Speaker (SP2)
• Disassembly of Lighting Wire P.C.B. Assembly

5
3.1. Disassembly of Upper Front
Panel Assembly
Step 1 : Remove 2 screws.
Step 2 : Remove Corner Guard.
Step 3 : Remove 2 screws.
Step 4 : Remove Corner Guard.

6
Step 5 : Remove 2 screws.
Step 6 : Insert two flathead screwdriver at the sides of the boss
and apply light force to push out the Upper Front Panel Assem-
bly by sequence (1-6) shown.
Caution : Do not exert too much force as it may damage
the Upper Front Panel Assembly.
Step 7 : Detach the (+) and (-) speaker wires.
Step 8 : Remove the Upper Front Panel Assembly.

7
3.2. Disassembly of Tweeter
Speaker (SP1)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 2 screws.
Step 2 : Remove the Tweeter Speaker (SP1).
3.3. Disassembly of Full Range
Speaker (SP4)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP4) as shown.
Step 3 : Detach the (+) and (-) speaker wires.

8
Step 4 : Remove the Full Range Speaker (SP4). 3.4. Disassembly of Full Range
Speaker (SP3)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP3) as shown.
Step 3 : Detach the (+) and (-) speaker wires.

9
Step 4 : Remove the Full Range Speaker (SP3). 3.5. Disassembly of Lower Front
Panel Assembly
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 2 screws.
Step 2 : Remove Corner Guard.

10
Step 3 : Remove 2 screws.
Step 4 : Remove Corner Guard.
Step 5 : Remove 2 screws.
Step 6 : Remove 2 screws.
Step 7 : Detach the Lower Front Panel Assembly slightly as
arrow shown.
Caution : Do not exert strong force as it may damage the
wiring within.
Step 8 : Lift up the Himelon.
Caution : Replace the Himelon if they are torn during dis-
assembling.