Panasonic SB-MAX770PU User manual

© Panasonic Corporation 2014, All rights reserved.
Unauthorized copying and distribution is a violation of
law.
PSG1402010CE
Speaker System
Model No. SB-MAX770PU
Product Color : (K)... Black Type
TABLE OF CONTENTS PAGE PAGE
1 Specifications ----------------------------------------------------- 2
2 Disassembly and Assembly Instructions ---------------- 3
2.1. Disassembly of Upper Front Panel Assembly------ 4
2.2. Disassembly of Tweeter Speaker (SP1)------------- 5
2.3. Disassembly of Full Range Speaker (SP2) --------- 5
2.4. Disassembly of Full Range Speaker (SP3) --------- 6
2.5. Disassembly of Lower Front Panel Assembly------ 6
2.6. Disassembly of Woofer Speaker (SP4)-------------- 8
2.7. Disassembly of Lighting Wire P.C.B.
Assembly ---------------------------------------------------- 8
3 Wiring Connection Diagram ---------------------------------10
3.1. Front Speakers--------------------------------------------10
4 Exploded View and Replacement Parts List -----------11
4.1. Cabinet Parts Location ---------------------------------11
4.2. Packaging --------------------------------------------------12
4.3. Replacement Parts List ---------------------------------13

2
1 Specifications
Front Speakers
Type 4 way, 4 speaker system (Bass reflex)
Speaker(s)
Super Woofer (Low) 38 cm cone type
Super Woofer (Medium Low) 20 cm cone type
Woofer 10 cm cone type
Tweeter 6 cm cone type
Impedance 3 Ω(High), 3 Ω(Medium Low),
5 Ω(Low)
Output sound pressure 91 dB/W (1 m)
Frequency range 25 Hz to 23 kHz (-16 dB)
30 Hz to 20 kHz (-10 dB)
Dimensions (W x H x D)
With Corner Guard 576 mm x 794 mm x 542 mm
Without Corner Guard 576 mm x 786 mm x 542 mm
Mass (Weight) 37.4 kg
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum ana-
lyzer.

3
2 Disassembly and Assembly Instructions
Caution Note:
• This section describes procedures for checking the operation and replacing the main components.
• For reassembly after operation checks or replacement, reverse the respective procedures.
• Special reassembly procedures are described only when required.
• Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
• During the disassembly and/or assembly process, please handle with care as there may be chassis components with sharp
edges.
• During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the service man-
ual.
• Select items from the following indexes when disassembly or replacement are required.
Front Speakers
• Disassembly of Upper Front Panel Assembly
• Disassembly of Tweeter Speaker (SP1)
• Disassembly of Full Range Speaker (SP2)
• Disassembly of Full Range Speaker (SP3)
• Disassembly of Lower Front Panel Assembly
• Disassembly of Woofer Speaker (SP4)
• Disassembly of Lighting Wire P.C.B. Assembly

4
2.1. Disassembly of Upper Front
Panel Assembly
Step 1 : Remove 4 screws.
Step 2 : Remove the Corner Guard.
Step 3 : Remove 4 screws.
Step 4 : Insert two flathead screwdriver at the sides of the boss
and apply light force to push out the Upper Front Panel Assem-
bly by sequence (1-7) shown.
Caution : Do not exert too much force as it may damage
the Upper Front Panel Assembly.
Step 5 : Detach the (+) and (-) speaker wires.
Step 6 : Remove the Upper Front Panel Assembly.

5
2.2. Disassembly of Tweeter
Speaker (SP1)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Remove the Tweeter Speaker (SP1).
2.3. Disassembly of Full Range
Speaker (SP2)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP2) as shown.
Step 3 : Detach the (+) and (-) speaker wires.
Step 4 : Remove the Full Range Speaker (SP2).

6
2.4. Disassembly of Full Range
Speaker (SP3)
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Slightly lift up Full Range Speaker (SP3) as shown.
Step 3 : Detach the (+) and (-) speaker wires.
Step 4 : Remove the Full Range Speaker (SP3).
2.5. Disassembly of Lower Front
Panel Assembly
• Refer to “Disassembly of Upper Front Panel Assembly”.
Step 1 : Remove 4 screws.
Step 2 : Remove the Corner Guard.
Step 3 : Remove 2 screws.

7
Step 4 : Insert two flathead screwdriver at the sides of the boss
and apply light force to push out the Lower Front Panel Assem-
bly by sequence (1-9) shown.
Caution : Do not exert too much force as it may damage
the Upper Front Panel Assembly.
Step 5 : Lift up the Himelon.
Caution : Replace the Himelon if they are torn during dis-
assembling.
Step 6 : Detach the 4P Wire Socket.
Step 7 : Remove the Lower Front Panel Assembly.

8
2.6. Disassembly of Woofer
Speaker (SP4)
• Refer to “Disassembly of Upper Front Panel Assembly”.
• Refer to “Disassembly of Lower Front Panel Assembly”.
Step 1 : Remove 8 screws.
Step 2 : Slightly lift up Woofer Speaker (SP4) as shown.
Step 3 : Detach the (+) and (-) speaker wires.
Step 4 : Remove the Woofer Speaker (SP4).
2.7. Disassembly of Lighting Wire
P.C.B. Assembly
• Refer to “Disassembly of Upper Front Panel Assembly”.
• Refer to “Disassembly of Lower Front Panel Assembly”.
Step 1 : Release the 4P wire from the hole of Lower Front
Panel Assembly.
Step 2 : Remove 4 screws.
Step 3 : Remove the Lighting Pieces.

9
Step 4 : Release the 4P wire from the slots.
Caution : During assembling, ensure that the 4P wire is
properly inserted into the slot.
Step 5 : Remove 2 screws.
Step 6 : Remove the Lighting Wire P.C.B. Assembly.

10
3 Wiring Connection Diagram
3.1. Front Speakers

11
4 Exploded View and Replacement Parts List
4.1. Cabinet Parts Location
SP4
SP3
SP2
SP1
25
25
25
22
20
20
19
19
18
18
17
17
17
17
17 17 17
17
16
16
16
16
16
16
16
16
16
16
16
21
21
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
15
15
15
15 15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
14
14
13-2
13-1
13
12
11
10
9
8
8
8
8
7
6
6
6
6
6
6
5
4
3
2
(LIGHTING P.C.B.)
1
c
c
a
b
a
b
d
d
e
e
g
f
h
h
i
i
gf
123456789
A
B
C
D
E
F
G
H
10 11 12 13
SB-MAX700PUK
CABINET DRAWING

12
4.2. Packaging
SB-MAX770PU
SB-MAX770PU
P3
P3
*P2
*P2 *P2
*P2
FRONT
P1
123456789
A
B
C
D
E
F
G
H
10 11 12 13
*P2
POLYFOAM (TOP)
POLYFOAM (BOTTOM)
SB-MAX770PUK
PACKAGING DRAWING

13
4.3. Replacement Parts List
4.3.1. Front Speakers
4.3.2. Packing Materials
IPSG1402
Safety Ref. No. Part No. Part Name &
Description Qty Remarks
CABINET & CHAS-
SIS
1 REE1926 LIGHTING WIRE
PCB ASS’Y 1
2 RGK2547-S FRONT ORNAMENT 1
3 RGL0801-Q LIGHTING PIECE 1
4 RGN3419-K SPEC LABEL L 1
4 RGN3419A-K SPEC LABEL R 1
5 RGP1693-K LOWER FRONT
PANEL 1
6 RGQ0812-K CORNER GUARD 6
7 RMQ0819 EVA PACKING 1
8 RMQ2123 EVA PACKING 4
9 RYP1970-K UPPER FRONT
PANEL ASS’Y L 1
9 RYP1971-K UPPER FRONT
PANEL ASS’Y R 1
10 RMQX0285-K EVA PACKING 1
11 RYQ1353-K NET FRAME ASSY
(WOOFER) 1
12 RYQ1354-K TWEETER HOLDER
ASS’Y 1
13 RYQ1355-K WOODEN BOX ASSY
(L) 1
13-1 K1MY04A00006 4P SPK CONNEC-
TOR HOUSING
(WHITE) L
1
13-2 RHQX1002W 2P SPK CONNEC-
TOR HOUSING
(WHITE) L
1
13 RYQ1356-K WOODEN BOX ASSY
(R ) 1
13-1 K1MY04A00007 4P SPK CONNEC-
TOR HOUSING
(RED) R
1
13-2 RHQX1002R 2P SPK CONNEC-
TOR HOUSING
(RED) R
1
14 XTB3+10GFJ SCREW 2
15 XTB4+12GFJ SCREW 30
16 XTB4+16AFJK SCREW 30
17 XTB4+10GFJ SCREW 8
18 RMF0600J HIMELON 2
19 RMF0600C HIMELON 2
20 RMF0600 HIMELON 2
21 RMF0600A HIMELON 2
22 RMQ2070 HIMELON 1
25 RKA0072-KJ LEG RUBBER 3
SPEAKERS
SP1 EAS6PH134A TWEETER 1
SP2 L0AA10A00040 WOOFER 1
SP3 L0AA20A00032 WOOFER 1
SP4 L0AA38A00010 WOOFER 1
Safety Ref. No. Part No. Part Name &
Description Qty Remarks
PACKING MATERI-
ALS
P1 RPG0K09 PACKING CASE 1
P2 RPN2637 POLYFOAM 2
P3 RPF0643 MIRAMAT BAG 2
Safety Ref. No. Part No. Part Name &
Description Qty Remarks