Panasonic SA-MAX8000GN User manual

© Panasonic Corporation 2015. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
PSG1502011CE
CD Stereo System
Model No. SA-MAX8000GN
Product Color: (K)...Black Type
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 3
1.1. General Guidelines---------------------------------------- 3
1.2. Before Repair and Adjustment------------------------- 3
1.3. Protection Circuitry---------------------------------------- 4
1.4. Caution For Fuse Replacement------------------------ 4
1.5. Safety Parts Information -------------------------------- 5
2 Warning-------------------------------------------------------------- 6
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices---------- 6
2.2. Precaution of Laser Diode------------------------------- 6
2.3. General description about Lead Free Solder
(PbF)---------------------------------------------------------- 7
2.4. Handling Precautions for Traverse Ass’y------------ 7
2.5. Grounding for electrostatic breakdown
prevention --------------------------------------------------- 8
3 Service Navigation----------------------------------------------- 9
3.1. Service Information----------------------------------------9
3.2. Software Update Procedure-----------------------------9
4 Specifications----------------------------------------------------10
5 Location of Controls and Components------------------ 11
5.1. Remote Control Key Button Operation ------------- 11
5.2. Main Unit Key Button Operation---------------------- 12
6 Service Mode-----------------------------------------------------13
6.1. Cold-Start -------------------------------------------------- 13
6.2. Sales Demonstration Lock Function ----------------13
6.3. Doctor Mode Table--------------------------------------- 14
6.4. Self-Diagnostic Mode -----------------------------------16
6.5. Self-Diagnostic Error Code Table-------------------- 16
7 Troubleshooting Guide --------------------------------------- 18
8 Disassembly and Assembly Instructions---------------19
8.1. Type of Screws -------------------------------------------19
8.2. Disassembly Flow Chart -------------------------------20
Please refer to the original service manual for:
OCD Mechanism Unit, Mechanism (BRS12C) Order No. PSG1303059AE
OSpeaker system SB-MAX8000GN, Order No. PSG1502012CE

2
8.3. Main Components and P.C.B. Locations-----------21
8.4. Disassembly of Top Cabinet---------------------------22
8.5. Disassembly of Fan Unit -------------------------------22
8.6. Disassembly of Front Panel Unit---------------------23
8.7. Disassembly of FL Display P.C.B. -------------------24
8.8. Disassembly of Illumination Jog P.C.B.-------------24
8.9. Disassembly of Illumination Left P.C.B.-------------25
8.10. Disassembly of BT&NFC P.C.B ----------------------25
8.11. Disassembly of Volume Jog P.C.B.------------------25
8.12. Disassembly of Illumination Right P.C.B.-----------26
8.13. Disassembly of USB P.C.B. ---------------------------26
8.14. Disassembly of Mic P.C.B.-----------------------------27
8.15. Disassembly of DJ Cabinet Unit----------------------27
8.16. Disassembly of Button Left P.C.B.-------------------28
8.17. Disassembly of Multi Control P.C.B.-----------------29
8.18. Disassembly of Button Right P.C.B.-----------------29
8.19. Disassembly of SMPS P.C.B.-------------------------30
8.20. Disassembly of Inner Chassis Unit ------------------30
8.21. Disassembly of Main P.C.B.---------------------------31
8.22. Disassembly of CD Mechanism Unit----------------32
8.23. Disassembly of CD Interface P.C.B.-----------------32
9 Service Position-------------------------------------------------33
9.1. Checking of FL Display P.C.B., Button Left
P.C.B., Button Right P.C.B. and Multi Control
P.C.B.--------------------------------------------------------33
9.2. Checking of SMPS P.C.B.------------------------------34
9.3. Checking of Main P.C.B.--------------------------------34
10 Block Diagram ---------------------------------------------------35
10.1. System Control -------------------------------------------35
10.2. Audio --------------------------------------------------------39
10.3. Power Supply ---------------------------------------------41
11 Wiring Connection Diagram---------------------------------43
12 Schematic Diagram---------------------------------------------45
12.1. Schematic Diagram Notes-----------------------------45
12.2. Main (IO Expansion) Circuit ---------------------------47
12.3. Main (Fan LED) Circuit ---------------------------------48
12.4. Main (DSP) Circuit---------------------------------------49
12.5. Main (Amp BTL) Circuit (1/2)--------------------------50
12.6. Main (Amp BTL) Circuit (2/2)--------------------------51
12.7. Main (MICON) Circuit (1/2) ----------------------------52
12.8. Main (MICON) Circuit (2/2) ----------------------------53
12.9. Main (Amp Single) Circuit (1/2)-----------------------54
12.10. Main (Amp Single) Circuit (2/2)-----------------------55
12.11. Main (FE) Circuit -----------------------------------------56
12.12. Main (Karaoke) Circuit----------------------------------57
12.13. Main (Digital Power) Circuit (1/2)---------------------58
12.14. Main (Digital Power) Circuit (2/2)---------------------59
12.15. Main (USB) Circuit---------------------------------------60
12.16. Main (AUX Tuner) Circuit ------------------------------61
12.17. Illumination Left, Illumination Right,
Illumination Jog and Volume Jog Circuit -----------62
12.18. FL Display Circuit ----------------------------------------63
12.19. Button Left Circuit----------------------------------------64
12.20. Button Right and Multi Control Circuit --------------65
12.21. Mic Circuit--------------------------------------------------66
12.22. USB and CD Interface Circuit-------------------------67
12.23. SMPS Circuit (1/2)---------------------------------------68
12.24. SMPS Circuit (2/2)---------------------------------------69
13 Printed Circuit Board ------------------------------------------70
13.1. Main P.C.B. (Side A)-------------------------------------70
13.2. Main P.C.B. (Side B)-------------------------------------71
13.3. Illumination Left, Illumination Right and FL
Display P.C.B. -------------------------------------------- 72
13.4. Button Left, Button Right, Mic and USB P.C.B. -- 73
13.5. Volume Jog, Illumination Jog, Multi Control
and CD Interface P.C.B.-------------------------------- 74
13.6. SMPS P.C.B.---------------------------------------------- 75
14 Voltage and Waveform Measurement-------------------- 77
14.1. Voltage Measurement ---------------------------------- 77
14.2. Waveform Chart------------------------------------------ 83
15 Exploded View and Replacement Parts List----------- 85
15.1. Cabinet Parts Location 1------------------------------- 85
15.2. Cabinet Parts Location 2------------------------------- 86
15.3. Cabinet Parts Location 3------------------------------- 87
15.4. Packaging ------------------------------------------------- 88
15.5. Mechanical Replacement Part List------------------ 89
15.6. Electrical Replacement Part List--------------------- 91

3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by in the
Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts
should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify
the original design without permission of manufacturer.
2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal
injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during
servicing.
3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be
1.1.2. Leakage Current Hot Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15μF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1-1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent)
may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the
limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is
returned to the customer.
Figure 1-1
1.2. Before Repair and Adjustment
Disconnect AC power to discharge AC Capacitors (C1001, C1002, C1003, C1004, C1006, C1518) through a 10 Ω, 10 W resistor to
ground.
Caution:
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 220~240 V, 50 Hz in FM Tuner at volume minimum should be ~ 850mA.

4
1.3. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.4. Caution For Fuse Replacement

5
1.5. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
Safety Ref No. Part No. Part Name & Description Remarks
24 RGR0455L-A REAR PANEL
33 RKM0744-K2 TOP CABINET
301 RAE1048Z-V TRAVERSE ASS'Y
A2 K2CJ2YY00097 AC CORD
A3 RQT9980-B O/I BOOK (En)
PCB14 REP5143B SMPS P.C.B (RTL)
DZ1001 D4EAY511A127 SURGE ABSORBER (E.S.D)
Q1403 B3PBA0000579 PHOTO COUPLER (E.S.D)
Q1405 B3PBA0000579 PHOTO COUPLER (E.S.D)
Q1404 B3PBA0000579 PHOTO COUPLER (E.S.D)
Q1505 B3PBA0000579 PHOTO COUPLER (E.S.D)
F1001 K5D103BNA005 FUSE
F1401 K5G501YA0081 FUSE
F1501 K5G502Y00006 FUSE
L1001 G0B183J00002 LINE FILTER
L1002 G0B183J00002 LINE FILTER
T1401 G4DYA0000688 SWITCHING TRANSFORMER
T1501 G4DYA0000691 SWITCHING TRANSFORMER
T1502 G4DYA0000691 SWITCHING TRANSFORMER
P1001 K2AZYA000005 AC INLET
R1001 D0GF105JA048 1M 1/4W
R1002 D0GF105JA048 1M 1/4W
C1001 F0CAF224A105 0.22uF
C1002 F0CAF224A105 0.22uF
C1003 F1BAF1020030 1000pF
C1004 F1BAF1020030 1000pF
C1006 F0CAF104A105 0.1uF
C1518 F1BAF1020030 1000pF

6
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi-
tive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. Precaution of Laser Diode
Caution:
This product utilizes a laser diode with the unit turned “on”, invisible laser radiation is emitted from the pickup lens.
Wavelength: 790 nm (CD)
Maximum output radiation power from pickup: 100 μW/VDE
Laser radiation from the pickup unit is safety level, but be sure the followings:
1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pickup lens for a long time.

7
Figure 2-1
2.3. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
2.4. Handling Precautions for Traverse Ass’y
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
2.4.1. Cautions to Be Taken in Handling the Optical Pickup Unit (OPU)
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
should be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FFC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

8
ble cable, cut off the antistatic FFC.
Figure 2-2
2.5. Grounding for electrostatic breakdown prevention
• As for parts that use optical pick-up (laser diode), the optical pick-up is destroyed by the static electricity of the working environ-
ment.
Repair in the working environment that is grounded.
2.5.1. Worktable grounding
• Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed and ground the sheet.
2.5.2. Human body grounding
• Use the anti-static wrist strap to discharge the static electricity form your body Figure 2-3.
Figure 2-3

9
3 Service Navigation
3.1. Service Information
This service manual contains technical information which will allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
3.2. Software Update Procedure

10
4 Specifications
QAmplifier section
RMS output power stereo mode
High Ch 500 W per channel (3 Ω), 1 kHz, 30% THD
Mid Ch 500 W per channel (3 Ω), 1 kHz, 30% THD
Low Ch 1000 W per channel (5 Ω), 100 Hz, 30% THD
Total RMS stereo mode power 4000 W
QDisc section
Disc played (8 cm or 12 cm) CD, CD-R/RW (CD-DA, MP3*)
*MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength 790 nm(CD)
QBuetooth®section
Version Bluetooth®2.1 + EDR
Class Class 2
Supported profiles A2DP, AVRCP, SPP, OPP, FTP
Operating frequency 2.4 GHz band FH-SS
Operation distance 10 m line of sight
QInternal memory section
Memory
Memory size 2 GB
Media file format support MP3 (*.mp3)
Memory recording
Bit rate 128 kbps
Memory recording speed 1x, 3x max (CD only)
Recording file format MP3 (*.mp3)
QTuner section
Frequency modulation (FM)
Preset memory 30 stations
Frequency range 87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals 75 Ω(unbalanced)
Amplitude modulation (AM)
Preset memory 15 stations
Frequency range 522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz (10 kHz step)
QTerminal section
USB port
USB standard USB 2.0 full speed
Media file format support MP3 (*.mp3)
USB device file system FAT12, FAT16, FAT32
USB recording
Bit rate 128 kbps
USB recording speed 1x, 3x (CD only)
Recording file format MP3 (*.mp3)
AUX IN 1
Audio input Pin jack
AUX IN 2
Terminal Stereo, 3.5 mm jack
Microphone
Terminal Mono, 6.3 mm jack
QGeneral
Power supply AC 220 V to 240 V, 50 Hz
Power consumption 340 W
Dimensions (W x H x D) 492 mm x 221 mm x 421 mm
Mass 7.1 kg
Operating temperature range 0 °C to +40 °C
Operating humidity range 35% to 80% RH
(no condensation)
Power consumption in standby
mode (approximate) 0.4 W
Power consumption in standby
mode (approximate)
(With “BLUETOOTH STANDBY”
set to “ON”)
0.5 W
Note:
1. Specifications are subject to change without notice.
Mass and dimension are approximate.
2. Total harmonic distortion is measured by the digital spec-
trum analyzer.
QSystem: SC-MAX8000GN Main Unit: SA-MAX8000GN
Speaker System: SB-MAX8000GN

11
5 Location of Controls and Components
5.1. Remote Control Key Button Operation

12
5.2. Main Unit Key Button Operation

13
6 Service Mode
6.1. Cold-Start
6.2. Sales Demonstration Lock Function
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Cold Start To carry out cold-start or initialize
to shipping mode
1. Unplug AC power cord.
2. Press & hold [POWER]
button.
3. Plug in AC power cord
while [POWER] button
being pressed.
4. Release [POWER] button.
Entering into
Sales
Demonstration
Lock Mode
To enter into the sales
demonstration lock mode.
1. Turn on the unit.
2. Select to any mode
function.
3. Press and hold
[;OPEN/CLOSE] and
[CD/RADIO/AUX] keys for
5 sec or more.
The display will show upon
entering into this mode for
2 sec.
Note: [;OPEN/CLOSE]
button is invalid and the main
unit displays "LOCKED" while
the lock function mode is
entered.
Cancellation of
Sales
Demonstration
Lock Mode
To cancel the sales
demonstration lock mode.
1. Turn on the unit.
2. Select to CD mode function.
3. Set volume to Vol 19.
4. Press and hold
[;OPEN/CLOSE] and
[CD/RADIO/AUX] keys for
5 sec or more.
The display will show upon
entering into this mode for
2 sec.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name

14
6.3. Doctor Mode Table
6.3.1. Doctor Mode Table 1
FL Display Key Operation
Front Key
Item
DescriptionMode Name
Doctor Mode
EEPROM
checksum
check
To enter into Doctor Mode In CD Mode:
1. Press [ ] button on
main unit follow by [4]
and [7] on remote control.
In CD mode:
1. Enter into Doctor Mode
2. To exit, press [DELETE]
button on remote control or,
press [POWER, /I] button
on Main Unit
Displaying of
1. Year Develop.
2. Model Type.
3. ROM Type.
4. Firmware Version.
(Display 1)
Cold Start To active cold start upon next AC
power up when reset start is
execute the next time.
In Doctor Mode:
1. Press [4] button on the
remote control.
(Decimal)
1 2 3 4

15
6.3.2. Doctor Mode Table 2
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Volume Setting
Check
FL Display Check
To check the volume setting of the
main unit.
To check the FL segment display.
All segments will light up while all LED
blink at 0.5s intervals.
In Doctor Mode:
1. Press [7], [8], [9] button on
the remote control.
In Doctor mode:
1. Press [1] button on the
remote control.
2. To cancel this mode, press
[0] button on the remote
control.
Press [7]: VOL50
Press [8]: VOL35
Press [9]: VOL0
Volume
In this mode, the tray will open & close
automatically.
Cancellation Display
Loading Test To determine the open & close
operation of the CD Mechanism Unit.
The counter will
increment by one.
When reach 99999999
will change to 00000000
Cancellation Display
Traverse Test To determine the traverse unit
operation for inner & outer access track.
The counter will
increment by one.
When reach 99999999
will change to 00000000
The counter will
increment by one.
When reach 99999999
will change to 00000000
Cancellation Display
Reliability Test
(Combination)
In this mode, ensure the CD is in the
main unit.
To determine the traverse unit
operation & open/close operation of the
mechanism.
In this mode, ensure the CD is in the
main unit.
In Doctor Mode:
1. Press [10] [2] [1] button
on the remote control.
In Doctor Mode:
2. To cancel this mode, press
[0] button on the remote
control.
2. To cancel this mode, press
[0] button on the remote
control.
2. To cancel this mode, press
[0] button on the remote
control.
1. Press [10] [1] [2] button
on the remote control.
In Doctor Mode:
1. Press [10] [1] [5] button
on the remote control.

16
6.4. Self-Diagnostic Mode
6.5. Self-Diagnostic Error Code Table
Self-Diagnostic Function (Refer Section 6.4. Self-Diagnostic Mode) provides information on any problems occurring for the unit and
its respective components by displaying the error codes. These error code such as U**, H** and F** are stored in memory and held
unless it is cleared.
The error code is automatically display after entering into self-diagnostic mode.
6.5.1. Power Supply Error Code Table
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Self Diagnostic
Mode
To enter into self diagnostic checking Step 1: Select CD mode
(Ensure no disc is inserted).
To exit, press [8] on main unit or
remote control.
Step 2: Press & hold [g] button
follow by [y/i] on
main unit for 2 seconds.
Error Code
Information
System will perform a check on
any unusual/error code from the
memory
Example: Step 1: In self diagnostic mode,
Press [g] on main unit.
To exit, press [8] on main unit or
remote control.
Delete error code To clear the stored in memory
(EEPROM IC)
Step 1: In self diagnostic mode,
Press [0] on remote control
for more than 5 seconds.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code F61 Diagnosis Contents:
Power Amp IC output abnormal.
Upon power on, PCONT=HIGH,
DC_DET_AMP after checking LSI.
Error Code F76 Diagnosis Contents:
Power Amp IC output abnormal.
DC_DET_PWR.
Error Code
F61-76
Diagnosis Contents:
Power Amp IC output abnormal.
Both DCDET (NG).
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.

17
6.5.2. CD Mechanism Error Code Table
6.5.3. Bluetooth Error Code Table
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code
CD H15
Diagnosis Contents:
CD Open Abnormal.
During operation POS_SW_R On
fail to be detected within 4 sec.
Error No. shall be clear by force
or during cold start.
Error Code
CD H16
Diagnosis Contents:
CD Closing Abnormal.
During operation POS_SW_CEN
On fail to be detected within 4 sec.
Error No. shall be clear by force
or during cold start.
Error Code
F26
Diagnosis Contents:
Communication between CD
servo LSI and micro-p abnormal.
During switch to CD func-tion, if
SENSE = “L” within fail safe time
of 20ms.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code F70 Diagnosis Contents:
Bluetooth Communication.
Communication between
Bluetooth module and micro-p
abnormal.
Error Code F77 Diagnosis Contents:
Bluetooth Address Error
If there is no valid Bluetooth
address stored in the
EEPROM IC.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.

18
7 Troubleshooting Guide
"Contents for this section is not available at time of issue"

19
8 Disassembly and Assembly Instructions
• This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo-
nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in this service
manual)
• Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
• During the disassembly and/or assembly process, please handle with care as there may be chassis components with
sharp edges.
• Avoid touching heatsinks due to its high temperature after prolong use.
• Be sure to use proper service tools, equipments or jigs during repair.
• Select items from the following indexes when disassembly or replacement are required.
• Disassembly of Top Cabinet
• Disassembly of Fan Unit
• Disassembly of Front Panel Unit
• Disassembly of FL Display P.C.B.
• Disassembly of Illumination Jog P.C.B.
• Disassembly of Illumination Left P.C.B.
• Disassembly of BT&NFC P.C.B.
• Disassembly of Volume Jog P.C.B.
• Disassembly of Illumination Right P.C.B.
• Disassembly of USB P.C.B.
• Disassembly of Mic P.C.B.
• Disassembly of DJ Cabinet Unit
• Disassembly of Button Left P.C.B.
• Disassembly of Multi Control P.C.B.
• Disassembly of Button Right P.C.B.
• Disassembly of SMPS P.C.B.
• Disassembly of Inner Chassis Unit
• Disassembly of Main P.C.B.
• Disassembly of CD Mechanism Unit
• Disassembly of CD Interface P.C.B.
8.1. Type of Screws

20
8.2. Disassembly Flow Chart
8.5. Fan Unit
8.4. Top Cabinet
8.6. Front Panel Unit
8.9. Illumination Left
P.C.B.
8.10. BT&NFC P.C.B.
8.7. FL Display P.C.B.
8.12. Illumination Right
P.C.B.
8.13. USB P.C.B.
8.22. CD Mechanism
Unit 8.14. Mic P.C.B.
8.19. SMPS P.C.B.
8.8. Illumination Jog
P.C.B. 8.20. Inner Chassis Unit
8.21. Main P.C.B.
8.15. DJ Cabinet Unit
8.16. Button Left P.C.B.
8.18. Button Right P.C.B.
8.17. Multi Control
P.C.B.
8.23. CD Interface P.C.B.
8.11. Volume Jog P.C.B.