Panasonic PVDM2792 - MONITOR/DVD COMBO User manual

Panasonic /
TV/DVD/VCR Combination
Operating Instructions
ModeINo.PV-DM2792,, /
/
/
• Initial Setup and Connection Procedures are on pages 14 to 17.
DIGITAL VIDEO _ ==lw.A.m
Asan ENERGY STAR _Partner,MatsushitaElectricCorporation ofAmericahas
determinedthatthisproduct or product modelmeetstheENERGY STAR _
guidelines forenergyefficiency,
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
SGPanishQuick Use Guide is included.
ufa para rApida consulta en espa5ol estA incluida.)

Important Safeguards and Precautions
READANDRETAINALLSAFETYAND I OUTDOOR ANTENNA INSTALLATION I
OPERATING INSTRUCTIONS, HEED ALL I SAFE ANTENNA AND CABLE CONNECTION
WARNINGS IN THE MANUAL AND ON UNIT An outside antenna orcable system must be propedy
IN TALLATI N grounded to provide some protection --_f_
INSTALLATION againat built up atatic abarges _ _';,_
1POWER SOURCE CAUTION and voltage. Section 810 f _"_-.._€'_
Operate only from power source indicated on ualt of the National Electrical _"_ _ _, _
or in this manual If uncertain have your Electric C°de, ANSI/NFPA 70 0n ,_J_, /_,,._,,_
Ut tyServceCompanyo VdeoPoductsDeae Canada, pa!tl oftbe _ _' .....
verify you r homepc wer sou rce _anaa_an.. _-{ectrtcat. Code) _l_o_
2 POWER CORD PLUG provides _nfom_afion .......................
regarding proper grounding of the mast and supporting
For safety, this unit has apolarized type plug (one s rucure grounding of the lead*in wire o an an enna
wide bla(_e), or a three-wire grounding type plug. discharge unit size of grounding conductors Iocation of
Always hold the plug firmly and make sure your an enna discharge unit connec ion o groundling
hands are dry when p_ugging in or unplugging the electrodes and requirements for the groundin electrode.
AC power cord. Regalariy remove duat, d,rt, etc, 2 KEEP A_JTENNA CLEAR OF HIGH VOt'_GE
on the plug• POWER LINES OR CIRCUITS
POLARIZEE) PLUG CAUTION_ Locate an outside antenna system well away from power
[rbe plug tits rote outie! one way. If if cannot be fu_y lines and eIec de Iigh or power circal s so it will never
_nserted, try reversing it. If if atd{w_IInot fit, have an touch these power sources should it ever fail When
eleatncian _nstali the proper wall outlet. DOnot inatalIing antenna, absolutely never touch power lines,
tamper with the plug. circuits or other power sources as this could be fatal.
GROUNDING PLUG CAUTION:
Tbeplugrequiresathree-halegroundingoutiet. USING THE UNIT I
If necessary, have an electdeian install the proper Before unit is brought OUtof storage or moved to a new location
outlet. DO not tamper with the plug, refer again to the INSTALLATION section of these safeguards.
3 POWER CORD 1 KEEP UNIT WELL AWAY FROM WATER OR
TO avoid unit malfunction, and to protect against MOISTURE such as vases sinks tubs etc.
elec deal shock, fire or personal injury: 2IF EXPOSED TO RAIN, MOISTURE, OR
-Keep power cord away from heating appliances STRONG IMPACT un lua unit and have i ins ec ed
and walking raffic. DO no res heavy objec s on lifi tat _ P _" P
rr II h " v r h w r r 'byaqua edse cetochn_c_a n before use.
o o suc objectso e t epo e cod. 3 ELECTRICAL STORMS
DO not tamper with the cord in any way ......
-An extension cord should have the same t e Dunng a hghtnmg storm, or before teawng unif unused for
YP extended periods of time, disconnect all equipment from
_,,,n ,_-_ _r,._. r.r _.1;e_C_l_;_,_0_ _._e_rounal ng) an d mlJs! be the power source as we,, as the antenna a_ld cab,e system.
y
-Overloaded walt outlets or extension cords is a4 WHEN UNIT IS PLUGGED IN
fire hazard. • DO NOT OPERATE IF:
Frayed cords, damaged plugs, and damaged or _liquid has spilled into unit..
cracked w re nsu a on a e beza dous and shou d unri was dropped or otherwise damaged,
be replaced by a qualified electdeian. - unit emits smoke, matodors, or noises.
4DO NOT BLOCK VENTILATION HOLES Immediately unplug unit, and have it inspected by a
service teChnician to avoid potential fire and shock hazards.
Ventilation openings in the cabinet release heat •Neverdr or sh an obectthro h o enins in unit.
• " k hop pu Y I ug p g
generated dunng operation, if bloc ed, eat $ hin in m I m "rfk h
il m r I in fir hr rh ouc g te agarts aycausealecto3shocko e azard.
bud_up ay esut a e azado eat n n frin " nh
.DO otpata y cog objectot etmy.
damagetocassettesord_scs. •K m n i "h k w fr m
F r r r n eep agecobecs, suc asspeaers, a ay o
o you p otectio : ..... unttoavodeect ca nterfeence
a. Never cover ventdation slots whde unit is ON,
or operate unit while placed on a bed, sofa, 5 USING ACCESSORIES
ru or other soft surface Use only accessories recommended by the manufacturer
g toavod skoffre shock o atbe hazads
b. AvOid balthin instatlation,such as a book case " " " , , -
or rack, unless properly yen ita ed. 6 CLEANING UNIT
5 AVOID EXTREMELY HOT LOCATIONS OR Unplug unit. Use a clean, dry, chemicallyuntreated ctathto
_HDDEN TEMPERATHR E r.HAN_E_ gen_ remove dust ot debris. DO NOT USE cleanincjfluids,
"_" . " " "_ " . aerosos o forcabai tl_tcoudover-spray orseep ntountand
DOnot place unri over or near a heater or radiator cause ale_rioal shock. An substance such as wax adl_esive
indirect sunlight inside closed vehicles _ m m _n ff ' '
inhi h m r 'r " v r_-F ...... 'tin v r labe, atc. ay a_-thecab atsu ace. Exposuratogreasy,
._:o gr te .l_,e a.!u e.[£ e _b ,(;_bL;)J,O[ 0 e humid,or dusty areas may adversaly affect internal parts.
z.__onumloi_y. ITunt[ IS suooenly _lloveg from a
cold place to a warm one, moisture may SERVICE
condense in unit and on the tape causing 1 DO NOT SERVICE PRODUCT YOURSELF
damage. Never subject unit to vibration, impact,
r I i h h rf i il in rn I If altercarefullyfoltowingdetaiIedoberatinginstraalions the
o pace tsot att esu ace st ted as tea n n r r n _*
_m_h_ri_,,_ti_r_m_,t u ridoes otopeatepoperiy, do otattempttoopeno
T AMOID PERSONAL INJURY re oveco ers, o ake anyadjustme Is otdescribed the
6•Omanual. Unplug unit and contact aqualified service technician.
Never place unit on support or stand that is not 2 REPLACEMENT OF PARTS
firm level and adequately strong M k r h rvi hni i n nl r ifi
' • '. • _ aesuet ese cetec ca useso ypatsspec ed
]t_e unit coalcl fail causing senous by he manufac ure or have equa sae y charac ede cs
mjurytoachddoradultand _ ri in t r Th' f n h riz im
ni aso g a pats. euseo u aut o edsubettutes ay
,damagetothe.u t. resalt in fire electric shock orotherhazards.
Moveinany _ppli,_nCeran d ca, 3 SAFETY CHECK AFTER SERVICING
QOui;_tor e_o_e_aiveefe_ce and _ Aftetunitissetvicedorrepaired requeatthatatderoughsafety
P, ,
n v n rf m " v m check be done as described in the manufacturer's service
u e esu aces aycauseobjecs co ertu .........
• Carefully follow all operating instructions, hterature to msu e video unit s msafe obe ating conaltion.

Safety Precautions/Mesures de sdcuritd
Warning :To preventfire or shock hazard,do notexpose t_is equipment to rainor moisture.
Caution :To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de pr_venir tout risque d'incendie ou de chocs _lectriques, ne pas
exposer cet appareil bla pluie ou bune humidit_ excessive.
Attention : Pour _viter les chocs _lectriques, introduire la lame la plus large de la fiche darts la
borne correspondante de la prise et pousser jusqu'au fond.
FCC WARNING :Any unauthorized changes or modifications to this equipment
would void the user's authority to operate.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELE REFER SERVICING TO QUALIFIED PERSONNEL.
•CAUTION: ]
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER
EN CAS D'OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTICE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this eqiupment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize an
electrical outlet different from that used by the receiver. If necessary, consult the dealer or an
experienced radio/TV technician for help. You may find the booklet, 'Something About Interference'
available from PCC local regional offices helpful.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: <http://www.eiae.or_>
This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included. Therefore, it
shouId be read carefully in order to avoid any problems.
Region Management Information
Region Management Information: This unit is designed and
manufactured to respond to the Regien Management
Information that is recorded on a DVD disc. If the Region
number described on the DVD disc does not correspond to
the Region number of this unit, this unit cannot play this disc.
The Region number
for this unit is 1. 3

Congratulations
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
andyour family years of enjoyment. Please fill in
the information below. The serial numberis on
the tag located on the back of your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No. PV*DM2792
Serial No
sAccessories
_ tT_ _T_ rn
[] Remote Control
LSSQ0302
[] Batteries
2 "AA"
To order accessories,
call toll free f-800-332-5368.
1) Open the cover.
_2) Insert batteries
as
marked.
3) Close the cover.
[] Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Break off the tab
to protect.
Record Tab _
Screw driver /
TO record again.
Cover the hole
with cellophane tape.
Only use tapes with the [_ mark in this unit.
Tape Speed Type of Video Cassette
Setting T60 T120 T160
2 Hours
SP (Standard Play) 1 Hour 2 Hours 40Minute_
LP (Long Play) 2 Hours 4 Hours 5 Hours
20 Minutes
SLP (SuperLong Play) 3 Hours 6 Hours 8 Hours
4

Initial Setup
Important Safeguards and Precautions /Safety Precautions ........ 2 - 3
Before Using ........................................................................................ 4
Information (Unit, Cassette, Disc) .................................................. 6 - 7
Location of Controls ...................................................................... 8 - 10
Connections ................................................................................ 11 - 13
Initial Setup .................................................................................. 14, 15
Reset Language, Channels, Clock, Time Zone Adjust ............... 16, 17
Basic Operation
Playback aTape ................................................................................ 18
Record On a Tape ............................................................................. 18
Copy Your Tapes (Dubbing) .............................................................. 19
Basic DVD Operation .................................................................. 20, 21
TV Operation
TV Operation ..................................................................................... 22
MTS Broadcast /TV Stereo System ................................................. 23
Closed Caption System ............................................................... 24, 25
TV Timer Features ............................................................................. 26
On-Screen Display (OSD) ................................................................. 27
FM Radio ...................................................................................... 28, 29
Timer Operation
Timer Recording ........................................................................... 30, 31
Advanced Operation
Cable Box Universal Remote Control Feature ............................ 32, 33
Tape Operation ........................................................................... 34 - 37
Special VCR Features ................................................................. 38, 39
V-Chip Control Feature .............................................................. 40 - 43
Audio Features ............................................................................ 44, 45
Video /Audio Menu ........................................................................... 45
Video /Audio Adjustment .................................................................. 47
Disc Operation ............................................................................ 48 - 51
MP3 Playback Operation .................................................................. 52
DVD Operation using On-Screen Displays ................................ 53 - 5_
DVD Lock Feature ............................................................................. 5_
For Your Information
Before Requesting Service .......................................................... 60, 61
Warning and Instruction Displays ...................................................... 6_-
Spanish Quick Use Guide /Gaia para rapida consulta ............. 65 - 71
Index ............................................................................................ 72, 7,!
Limited Warranty ............................................................................... 74
Customer Services Directory ............................................................ 7_
Settings for DVD Operation ........................................................ 57 - 5_
Language Code List .......................................................................... 6,!
t

•e_'_ ;e | ; - - •
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Head Clog Sensor
During playback this
screen appears if clogging
is detected. To remove
screen, press PLAY on the
remote or unit.
•Use "dry" type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
•Follow cleaning tape directions carefully.
Excessive use of head cleaning tape can shorten
the video head life.
• If head clog symptoms persist, contact your
nearest Factory Service Center or authorized
Service Center. (See Page 64.)
Unitautoadjustsclock for DST (DaylightSaving]]me.)
•Spring (First Sunday in April)
DST : ON _ Sets clock ahead one hour.
•Autumn (Last Sunday in October)
DST :ON _ Turns clock back one hour.
• If your area does not observe Daylight Saving
Time, select DST : OFF (see "Clock" on pages 16
and 17).
• Keep these time changes in mind when
programming the unit for timer recordings.
Dioital Auto Trackino
Continuously analyzes the signal and adjusts for optimum
picture quality.
Manual Trackina Control fto reduce picture noise_
Use during Playback and Slow Motion mode to reduce
picture noise. Press the 3 or 6 number key on the remote
control or CH _,V on the unit untilthe picture clears up.
To return to A_o Tracking, press POWER off, then on
again a few seconds later.
V-Lock Control
InStillmode, the3 or 6 numberkey onthe remotecontrolor
CH _,V onthe unitoperate as a V-Lock controlto reducejitter.
PanaBlack _Picture Tube
This unit uses a PanaBlackTM picture tubefor better color
reproduction and picture contrast.
6
Display
Picture Tube: 27 inch measured
diagonal 100_deflection
Picture Tube
VCR
Video Recording System:4 rotary heads helical
scanning system
Audio Track: 1 track (Normal)
2 channel
(Hi-Fi Audio Sound)
Tuner
Broadcast Channels:
CABLE Channels:
FM Radio
Band range:
General
Power Source:
Power Consumption:
Television System:
Speaker:
Operating Temperature:
Operating Humidity:
Weight:
Dimensions:
Discs played
(1) DVD-VIDEOdisc
VHF 2 - 13, UHF 14- 69
Midband A through I(14 o-22)
SupefoandJ throughW (23~36)
Hyperband AA ~EEE (37o-64)
Lowband A-5 ~A-1 (95 _ 99)
Speda{ CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 - 125
87.5 - 108.1 MHz
120VAC, 60 Hz
Power On
Approx. 170 watts
Power Off
Approx. 3.5 watts
EIA Standard NTSC color
2 pieces
5°Co-35 °C(41"F_95 °F)
10 % - 75%
42 k_ (92.4 Ibs.)
772 (W) x 654 (H)x 533(D)mm
30-3/8" (W) x 25-3/4" (H)
x 21" (D)
5" (12 cm) sthgle-sided,
single-layer
5" (12 cm) single-sided,
double-layer
5" (12 cm) double-sided,
double-layer
(one layer per side)
3" (8 cm) single-sided,
single-layer
3" (8 cm) single-sided,
double-layer
3" (8 cm) double-sided,
double-layer
(one layer per side)
5" (12 cm) disc
3" (8 cm) disc
(2) Compact disc
(CD-DA, CD-RW,
VIDEO CD)
Digital audio output:
Optical digital output: Optical connector
Pickup: Wave length:
655 nm (DVD)
790 nm (Video CD/CD)
Laser power: CLASS II
Note: Designsand specifications are subject to change
withoutnotice.

Disc formats supported bythis unit
The unit can play back discs bearing any of
the following marks:
DVD
",,,DEe 3" (8 cm) disc /5" (12 cm) disc
r_ Video CD
3" (8 cm) disc /5" (12 cm) disc
co
=_j__,,_._ 3" (8 cm) disc /5" (12 cm) disc
Discswhich cannot be playedwith this unit
DVD with Region No other than "1" or "ALL"
DVD of PAL system
DVD-ROM
DVD-R/DVD-RAM
CD-ROM
CDV
CD-G
•Do not try to play a Photo CD.
_is a registered trademark.
Handling precautions
• Only hold disc by edges as shown.
Fingerprints, dirt, and scratches
can cause skipping and distortion.
• Do not write on label
side of disc.
• Never use record
cleaning sprays, benzine,
thinner, static electricity
prevention liquids, or any
other solvent.
• Be careful not to drop or
bend disc.
• Do not place more than
1 disc on disc tray.
• Do not try to close disc
tray when disc is not
properly placed.
• Always store discs in their
proper cases when
not in use.
Angle
Some DVD discs feature scenes simultaneousIy
shot from different angles. The ANGLE button can be
used to view the scene from different angles.
(ANGLE Indicator lights up on the unit when a scene
recorded at different angles is detected.)
Chapter Number
Titlesaresubdivided into numberedsections. You can
quicklysearch fora favoritescene usingthese numbers.
DVD
A high-density optical disc on which high-quality
pictures and sound have been digitally recorded.
DVD incorporates new video compression technology
(MPEG II) and high-density recording technology
which allow entire movies to be recorded with
incredible playback quality.
Playback Control
With Video CD (version 2.0), scenes or information
may be selected for viewing or listening from an
interactive menu that appears on the TV screen.
Subtitles
WrittendiaJoguewhichappearsatthebottomof thescreen.
Time Number
The elapsedplay timefromthe startof a disc ortitle.
Use toquickly find scenes. (Maynotworkwithsomediscs.)
Title Number
For DVD discs with two or more titles, the title is
numbered as title 1,title 2, etc.
Track Number
Numbers assigned to tracks on Video CDs and CDs
to allow specific tracks to be quickly located.
Video CD
CD containing picture and sound with same quality
level as video tape. This unit also supports Video
CDs with playback control (version 2.0).
X
To clean disc surface
With a soft, damp (water only) cloth, gently wipe from
the center hole to the outer edge as shown below.
(Wiping in a circular pattern will scratch the surface.)
0 ×
Ifdisc is brought from a cold toa warm
environment,moisturemay form on thedisc
Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216
and4,819,098, licensedfor limited viewing usesonly.
This product incorporates copyright protection technology
that is protected by method ctaims of certain U.S.Patents
and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited. 7

EJECT/OPEN/CLOSE \
Sea next page. \
POWER \,
Turn the unit an or oft. \
\
TVNCR
Sets toTV/VCR mode,
MUTE
Mutes the sound instantly,
CHANNEL UP/DOWN ---_-.
Selects a channel _'_--
SURROUND -- --_ "
Hears a deeper, 3-0 sound effect. \
NUMBER Keys
Selects a channe_directly.
ANGLE --
Selects the desired _ng_e
in DVD mode.
AUDIO -_-
Selects the desired audio r_ode.
TITLE--
Selects the desired title by number
on some bVDs. /
SELECT A,_.411_
Control navigation around /_
on-screen menu. //
ACTION _ __ _ jr
Displays Main Menu.
BE]
Sets a selected menu.
REW/SLOW-
Rewinds tape and seamhea reverse
scene. Decreases slow motion
speed in Still mode.
S'fllJ./PAU SE ----- ---- ----_'
Pauses picture in P(ay mode and
frame advance picture in Slit( mode.
SKIPMHI/SEARCH
Skips back one chapter or t_ack. Goes to
previous rnenu screen. Goes directly
to the desired recording. Locates end
point of recording.
pLAy -- ---- ---- -- ----J
Begins playback.
SKIPIHH/CM SKIP/ZERO SEARCH J
Skips one chapter m track. Goes to next
_creen. in Stop mode, goes to the counter
'0:00:00'. In Play mode, skips over I to
3 minates of tape.
8
CD
FDVD
/Sets to DVD mode.
IF- LIGHT
/See next page.
//-- DSS/CABLE
Sets the remote to control some
basic DDS or Cable box functions.
FM
ReceivesFM radiosignal.
_- --VOLUME UP/DOWN
Adjusts volume.
_--- RAPID TUNE
Displays the last channel
you were watching,
F-- ADD/DELETE/CLEAR
/Adds or deletes a channel
Cecee_s an item on the screen.
SUBTITLE
So,cotsa differentsubt_Ie)angusge.
Displays the TV status and c]cok.
)n DVD mode, dispJays disc and
unft information.
In DSS or CABLE mode, it may be
eeeessa[y after ehs_el aetcoflom
s DVD mecu.
3GRAM
Displays SET PROGRAM screen.
You can set Timer Program and
On-Timer.
Fast forwards tape and searches
forward scene. Increases slow
I mode.
RESET
Enlarges spec4fic podiona of DVD
picture. Resets te "0:00:00' at
desired porlien of tape.
Records a program.
RETURN/SPEED
Returns to DVO menu screen.
So)acts recording speed of tape.
--STOP Stops playback.

g _ g g g g g | -•
Universal Light Tower _ Illuminated Remote Control
LIGHT button:
When LIGHT is pressed, (DVD, v_, DSS/CABLE, CH UP/DOWN, VOL UP/DOWN)
buttons will light for 5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the battery.
EJECT/OPEN/CLOSE button:
When this button is pressed in TV-VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or cIoses. m
I\
Remote Sensor
ANGLE Indicator
Lights up when a scene _ _ _ REC Indicator
recorded at different _ _ Lights up during recording.
angles _sdetected._ In Rec Pause or OTR
(DVD only). _ Pause mode, the Indicator
Pg. 49 PROG TIMER Indicator flashes.
Lights up when the unit is set for Pg. 18
Timer Recording. It flashes when
a Timer Recording has been set
with no tape inserted, the dock is
not set, or the tape is in motion.
Pg. 30
Lights up when the On Timer is set.
Pg. 26
9

If the disc cannot be removed...
First, unplug unit.
Then, prepare a rigid wire (e.g. an
extended paper clip) and, applying
moderate force, insert it straight into the
hole at the base of the tray. The tray will
eject a little. New, pull the tray all the
way out and remove the disc.
\
S
/
// Over2Inches
l\ J
PHONES
Connect an earphone
or headphones.
AUDIO/VIDEO IN
Connector
Connect from other
component.
POWER (See page 8.)
STOP (See page 8.)
PLAY (See page 8.)
OPEN/CLOSE (See page 8.)
REWIND/SEARCH (See page 8.)
SKIPI<< (See page 8.)
SKIPIz_I(See page 8.)
_Disc Tray _Cassette I//
/Compartment _/
>-_=_ _ _ ........
c221212'2LS2222o':2
(See page 8.)
TRACKING UP/DOWN
(See page 8.)
VOLUME UP/DOWN
(See page 8.)
REC
(See page 8.)
PLAY/REPEAT
(See page 8.)
STOP/EJECT
(See page 8.)
FAST FORWARD/
SEARCH
(See page 8.)
10 _,IP-E'TT"-I_IImBTITdp_ELI'.7)+FTI+#+[+_IPTILW_,_:"_ -,,i IS +,,,_J"_]',P.IIP, T+%]i_T_,]

•_• • • • • g-•
VHF/UHF Antenna
Input Terminal
See below.
Audio Output m
Connector (L/R)
Pg. 12
AC Power Plug
When plugged into an AC outiet,
this unit consumes 3.5 W of
eIectric power in OFF condition.
talaudio
outputconnector
Pg. 13
For ANTJCable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.
For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF
terminal on the unit with a RF
cable.
WARNING:
Overtightening "Nut type" RF coaxial cabIes
may damage jacks. Finger tighten only.
UNIT VHF/UHF
Cable TV
Converter Box
%. ANT./CABLt::
11

g-g g | -•
•Unit --) Amplifier -) Speaker
Ampl!t_er
Speaker Speaker
Unit
[_ Ready Checklist
[] Turn down the volume, then turn this unit, as well as
other equipment to be connected, off before
proceeding with connection.
[] Do not block ventilation holes of any of the
equipment and arrange them so that air can
circulate freely.
[] Read through the instructions before connecting
other equipment.
[] Ensure that you observe the color coding when
connecting audio and video cables.
Enjoying digital audio output from the
digital audio output connector
Notes on audio output from the optical digital
audio output connector
Disc Sound
recording
format
DVD
Dolby Digital
Linear PCM
(48/96 kHz
16/20/24 bit)
dts
Video
CD MPEG 1
CD Linear PCM
Optical digital audio
output from connector
Dolby Digital bitstream
(1-5.1 ch) orOFF (no
output) *_
Linear PCM (2ch)
(48 kHz sampling/16 bit
only).2 or no output *_
Bitstream or no outpuW
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)
"1 The type of audio output from the connector can be
selected by the Settings for DVD Operation. (See
page 60.)
*2 Sound having 96 kHz sampling is converted into 48
kHz sampling when it is output from the unit's optical
digital audio output connector.
Manufactured under license from Dolby
Laboratories. "Dolby", and the double-D
symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997
Dolby Laboratories, Inc. All rights reserved.
12
For your reference:
•Dolby Digital is a digital sound compression technique
developed by the Dolby Laboratories Licensing
Corporation. Supporting 5.1-channel surround sound,
as well as stereo (2-channel) sound, this technique
enables a large quantity of sound data to be efficiently
recorded on a disc.
• Linear PCM is a signal recording format used in CDs.
While CDs are recorded in 44.1 kHz/16 bit, DVDs are
recorded in 48 kHz/16 bit up to 96 kHz/24 bit.
• If you have a Dolby Pro Logic Surround decoder, you
will obtain the full benefit of Pro Logic from the same
DVD movies that provide full 5.1 channel Dolby Digital
soundtracks, as well as from titles with the Dolby
Surround mark. For information on Panasonic or
Technics Dolby Pro Logic Surround Sound Decoders
please contact your local dealer.

m
•Unit -) Decoder with Dolby Digital --) Amplifier --) Speaker
or /
dts (digital theater systems)
When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream
is output from the unit Optical digital audio output connector. When the unit is connected to a
Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home.
[An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or
dts decoder is used.]
Notes on connecting an Optical
digital audio cable (optional)
•Firmlyconnect the cable to
the connectoF.
Optical digital audio
cable (optional)
TOo_cal digitalaudio DecorderwithDolbyDbgital/
inputconnector dtsproces.sipg (optional)
Caution for optical digital audio
output connector:
• When connecting an amplifier (with
an Optical digital input connector)
which does not contain the Dolby
Digital or dts decoder, be sure to
select "OFF" at "Dolby Digital" and
"OFF" at "dts" of the Settings for
DVD Operation "AUDIO OUTPUT"
(see page 58). Otherwise, any
attempt to play DVDs may cause
such a high level of noise that it may
be harmful to your ears and damage
your speakers.
• When a dts decoder is connected,
please select "Bitstream" at "dts" of
the Settings for DVD Operation
"AUDIO OUTPUT". If "OFF" is
selected, there will be no sound.
(See page 58).
• Video CDs and CDs can be played
as normal.
Note:
• Some dts decoders which do not
support DVD-dts interface may not
work properly with the unit.
Ampl(fier
Speaker
Front
Speaker
13

!0!
Please make all cable or antenna connections before powering on.
Press v_VRon the remote for TV-VCR mode.
Plug the unit power cord into an AC wall outlet.
Press Power* on the remote or unit. The unit
comes on and auto channel and clock set starts.
• If you use a cable box, turn it on and set it to the Public
Broadcasting Service (PBS) channel in your time zone.
Ifyou use a DSS receiver, it must be turned off.
Settings are made automatically.
When setup is done, this screen appears.
POWER
TV-VCR
SELECT
SET
ACTION
cD oo c_"
CE) (3D C3D
If AUTO CLOCK SET IS INCOMPLETE
screen appears, set the clock using MANUAL
CLOCK SET procedure on next page.
14

TO CLOCK SET was incomplete, manually
_eclock as follows.
Press ACTION on the Remote to
display SET CLOCK Menu screen.
Press • • to select the month
and press SET to set. In the same
manner, select and set the date,
year, time, and DST. (Daylight
Saving Time)
DST:ON
Press ACTION twice to start
CLOCK and exit.
When moving unit to a new location, or if a
mistake was made in the Initial Setup section.
• Make sure a tape isnot inserted in the unit. II
1Turn the unit
Power on.
Press and hold both PLAY and
FF on the unit for more than 5
seconds.
• The power will shut off.
• Please ignore"NO CASSETTE" warning.
3Do"lnitial Setup" on page 14.
Note to CABLE System Installer
This reminder is provided to call the
CABLE (Cable TV) System Installers
attention to Article 820-40 of the NEC
that provides guidelines for proper
grounding and, in particular, specifies
that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as practical.

1Press ACTION* to display MAIN MENU.
mLanguage
1) Press Ay,q I_ to
select language
icon.
2) Press SET
repeatedly.
For Spanish
For French
For English
3) Press ACTION to
exit.
='=Channels
1) PressAV'_)_to
select"CH."
2) Press SET.
3) Press AY to select
"ANTENNA," then
press SET to set
your antenna system
("TV" or "CABLE").
4) Press Ay to select
"AUTO SET," then
press SET.
• After Channel Auto
Set is finished, Clock
Auto Set will be
performed.
cIfclock is set manually,
lock Auto Set will not
be performed.)
•Clock
1) Press ,AV_I Jibto
select "CLOCK."
2) Press SET.
("TIME ZONE ADJUST"
appears en_ when
auto clock i._set.)
3) Press A_, to select
"MANUAL," then
press SET.
(For Auto Clock Set,
select "AUTO CLOCK
SET," and press SET.)
<Example MANUAL
CLOCK SET screen>
Continued on the
next page.
16

4) Press &V and
press SET to select
and set the month,
date, year, time, and
DST (Daylight Saving
Time),
To Make Corrections,
repeatedly press • •
to move to error, then
correct.
5) Press ACTION
twice to start the
clock and exit this
mode.
•Time Zone Adjust
(Only whenAuto Ciock is set.)
1) Press AV• • to
select "CLOCK."
2) Press SET.
3) Press &1' to select
"TIME ZONE
ADJUST" and
press • or • to
subtract or add
hour(s) as
necessary.
4) Press ACTION
twice to exit.
Add or Delete aChannel
To add channel:
Select channel with number
keys and press ADD/DLT.
To delete channel:
Select channel with CHAr
or number keys and press
ADD/DLT.
/
17

I_l_Ready Checklist
[]All connections are made.
[] Your unit is plugged in.
I ]ln.sertatape.
I_IThe unit powercomes
on automatically.
°°'d-I
To prevent tape am, _'%_'_%:2_
remove loose or peeling _
labels from tapes. _'_._zX
Press PLAY* to play a tape.
•Iftape has no record tab (seepage 4),
auto play begins.
• Forward/Reverse scene search
--) Press PP/SLOW+ or PEW/SLOW-.
--) Press again or PLAY to release.
•Still (Freeze) picture
--) Press STILL/PAUSE
--) Press PLAY to release.
• Slow Motion picture
-) Press FP/SLOW+ (increases speed) or
PEW/SLOW- (decreases speed) in
Still mode.
--) Press PLAY to release.
• Frame by Frame picture
-) Press STILL!PAUSE in Still mode.
-) Press PLAY to release.
O
• These features work best in SP or SLP mode.
• After the unit is in Still or Slow mode for 3
minutes, it will switch to Stop mode automatically
to protect the tape and the video head.
•Stop -) Press STOP
•Rewind tape --) Press PEW/SLOW-
in Stop mode
•Fast forward tape -) Press FF/SLOW+
in Stop mode
• Eject tape -e. Press EJECT on the remote
or STOP/EJECT on the unit
Operation using unit buttons
PLAY/
Insert a tape. REPEAT CH _,V
PEG Indicator Press to stop
and/or eject tape. J
18
Insert a tape with record tab.
• The unit power comes on automatically.
Press OH AV or number keys toSelect Channel.
• For "LINE" input, see bottom of next page.
Press SPEED to select recordingspeed (see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
Press REC to start recording.• To editout unwantedportions, press
STILIJPAUSE to pauseand resume
recording.
• You cannot view anotherchannel during
recording.
Stop ..-) Press STOP
One Touch Recording (OTR)
Press REC repeatedly --No,m_,Re_--,.o3o--,._oo
to set the recording C "")
length (30 min - 4 hours.) 4:_..-_:00.,-2:_,,-_;_0.,-.-
• The unit stops recording at a preset time.
• PROG TIMER Indicator lights on the unit.
• After the unit has been in Rec Pause mode for
5 minutes, it will stop automatically to protect
the tape and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
SELECT
&T<II_--
SET
ACTION
REW/SLOW-
STILL/
PAUSE
ccccccccccccccccccc_@_
_ GD GD
_oo_
EJECT
CH&
¢HV
NUMBER
keys
DISPLAY
PLAY
-- FF/SLOW+
STOP
REC
SPEED

Connections you'll need to make Recording (Editing) unit
Playing (Source) VCR
R-AUDIO-LVIDEO IN FROM
@ ANT.
1
2
Insert pre-
recorded tape. Insert blank tape
with record tab.
• Dubbing tapes protected
with Copy Guard will have
poor quality results.
Select "LINE" mode.
See "Selecting Input Mode" below.
IPAUSE at starting_ _ i press PLAY thenpoint to put in
Standby mode.
IPress REC, then
REC STILL/PAUSE IPress STILL/PAUSE
{_ _Iimmediately to put in
Standby mode,
(Perform operation of steps 4 and 5 on both units at same time.)
Press PLAY Press STILL/PAUSE
to start dubbing. STILL/PAUSEto start dubbing.
5Press STOP
to stop dubbing. STOP Press STOP to stop dubbing.
0
• Unauthorized exchanging and/or
copying of copyrighted recordings
may be copyright infringement.
• Please note that some tapes
cannot be dubbed on this unit.
Also, it is not possible to dub
DVD/Video CD/CD to VHS tape
using this unit.
Method 1:
Press CH AV. The display will change as follows.
Method 2: _MNE_ _1_-_2/CABLE)4-b3_ TV)
a Press ACTION for MAIN MENU.
b Press AV_I • to select "TV", then press SET
for SET UP TV screen.
c Press AV to select "INPUT SELECT," and
then press SET to select "TUNER" or "LINE"
d Press ACTION twice to exit this mode. 19

_Ready Checklist
[] All connections are made. (See page 11.)
[] Your unit is plugged in.
[] If unit is connected to an audio amplifier,
turn the stereo system's power on.
POWER--
NUMBER
TITLE
PLAy
REW/SLOW-
STILL/
PAUSE
SKIP- /
SKIP+ /
_GD_
(3D QD QD
/
OPEN/
JCLOSE
DVD
_10
MENU
SELECT
_v<l,
SET
FF/SLOW+
-STOP
RETURN
Operation using unit buttons
4Press PLAY. 3"7
3Insert disc. Press
OPEN/CLOSE.
1Press STOP.
*_InteractNe DVD...
May include multiple camera angles,
stories, e_c.
.2 Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that
appears on the screen.
2O
1Press POWER* on the remote or unit.
Press DVD to select DVD mode.
If a disc is already inserted, go to step 4.
(Depending on the disc, playback may start
automatically .)
Insert a disc.
1) Press OPEN/CLOSE.
2) Place disc into disc tray.
•Hold disc by its edges only
(page 7) with printed side up
and use guides to place into
tray. Use O 3"(8 cm) oral
5" (12 cm) disc.
Press PLAY to start play.
Disc tray closes automatically.
__ • You may also close the t_ay
by pressing OPEN/CLOSE
• Data reading time differs with
each disc.
<Example>
If an interactive DVD *_ or a
Video CD with playback
control *= is used and a TITLE
MENU appears, go to step 5.
Dogs
l of the world
<Example>
Press &V_I • or
number key(s) (see
below) to select title
I nd press SET to
play.
Using number key(s)
starts playautomatically.
<Example> 1 digit number 1 ,•• 1
2 digit number 12,,,,,>10 1 2
3 digit number 123,*,100 1 2 3
Press SKIP IH_ or I<N!to go to next or previousmenu screen.
• SKiP function not available with all discs.
Please refer to disc jacket for operation information.
To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD}
Press STOP to stop play.
Press OPEN/CLOSE to eject the disc.