Panasonic TX-29P82X User manual

Power Source AC Auto 110-240 V, 50/60 Hz
Power Consumption 158 W
Standby condition : 0.8 W
Aerial Terminal Impedance : 75Ω, Coaxial type
Tuning System Frequency Synthesizer
Auto Search Tuning
Pos : 100 Positions
Receiving System 17 Systems
Receiving Channels Regular TV
VHF BAND
UHF BAND
CATV
2-12 (PAL/SECAM B, K1)
0-12 (PAL B AUST.)
1-9(PALBN.Z.)
1-12 (PAL/SECAM D)
1-12 (NTSC M Japan)
2-13 (NTSC M U.S.A.)
21-69 (PAL G,H,I/SECAM G,K,K1)
28-69 (PAL B AUST.)
13-57 (PAL D,K)
13-62 (NTSC M Japan)
14-69 (NTSC M U.S.A.)
S1-S20 (OSCAR)
1-125 (U.S.A. CATV)
C13-C49 (JAPAN)
S21-S41 (HYPER)
Z1-Z37 (CHINA)
Intermediate Frequency 38.0 MHz
© 2002 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TX-29P82X
MX-10 Chassis
Video
Sound
Colour
31.5 MHz (D,K) / 32.5 MHz (B,G)
32.0 MHz (I) / 32.5 MHz (M)
33.57 MHz (PAL) /
33.6 MHz (SECAM)
34.42 MHz (NTSC) /
33.75 MHz (SECAM)
Receiving Stereo Sound System QUADRA STEREO / TEXT
Video/Audio/Terminals
AV 1, 2, 3
Y/P
B/P R
Monitor Out
IN S-Video Y:1.0Vp-p 75Ω
DVD IN S-Video C:0.3Vp-p 75Ω
(Phone type) Y:1.0Vp-p 75ΩPB,
PR:0.7Vp-p 75ΩVideo 1.0Vp-p
75ΩAudio Approx. 400mV 47KΩ
Video 1.0Vp-p 75Ω
Audio Approx. 400mV 47KΩ
High Voltage 31.0 (+0.7, -1.5kV) at zero beam
current
Picture Tube M68LQK186XH Type 29 (68 cm)
Measured diagonally, 104°
deflection
Audio Output 16 W speaker
Dimensions (W x D x H) 699 mm x 509 mm x 584 mm
Weight (Mass) 49 kg (Net)
Accessories Supplied Remote Control Transmitter
1. R6(AA) Battery x 2
Note:
Specifications are subject to change without notice. Mass and
Dimensions shown are approximate.
Colour Television
Specification
Order No. MTV0109132C3

1 Safety Precautions 3
1.1. General Guide 3
1.2. Leakage Current Cold Check 3
1.3. Leakage Current Hot Check (See Fig. 1) 3
1.4. X-Radiation 3
2 Location of Controls and Circuit Boards 4
2.1. REAR VIEW 4
2.2. LOCATION AND FUNCTION NAME OF CIRCUIT BOARD
4
3 Service Hints 5
3.1. HOW TO MOVE CHASSIS INTO SERVICE POSITION.
5
4 MARKET MODE FUNCTION 6
5 ADJUSTMENT PROCEDURE 8
5.1. B VOLTAGE 8
5.2. RF AGC 8
5.3. HIGH VOLTAGE 8
5.4. SUB TINT 8
5.5. SUB CONTRAST 8
5.6. PAL COLOUR OUTPUT 9
5.7. NTSC COLOUR OUTPUT 9
5.8. COLOUR PURITY 10
5.9. CONVERGENCE 10
5.10. WHITE BALANCE (MARKET MODE CHK 3) 11
6 Memo 12
7 CONDUCTOR VIEWS 13
7.1. T-Board (TNP4G115AF) and L-Board (TNP4G107AV) 13
7.2. A-Board (TNP4G164AD) 14
7.3. H-Board (TNP4G173AA), X-Board (TNP4G108BB) and
GM-Board (TNP4G118AN) 15
8 SCHEMATIC DIAGRAMS 17
8.1. SCHEMATIC DIAGRAM FOR MODEL TX-29P82X (MX-
10A CHASSIS) 17
8.2. Main Board (TNP4G164AD) 19
8.3. Rear AV Circuit (TNP4G173AA) 21
8.4. CRT Circuit (TNP4G107AV) 23
8.5. Pincushion Circuit (TNP4G108BB) 24
8.6. Teletext Circuit (TNP4G115AF) 25
8.7. Geomagnetic Circuit (TNP4G118AN) 26
9 PARTS LOCATION 27
10 Replacement Parts List 29
10.1. Replacement Parts List Notes 29
10.2. Replacement Parts List 30
CONTENTS
Page Page
2
TX-29P82X

8.3. Rear AV Circuit (TNP4G173AA)
TX-29P82X
21

8.7. Geomagnetic Circuit (TNP4G118AN)
TX-29P82X
26

8.4. CRT Circuit (TNP4G107AV)
TX-29P82X
23

8.2. Main Board (TNP4G164AD)
Main Board (1/2)
TX-29P82X
19

Main Board (2/2)
TX-29P82X
20

8 SCHEMATIC DIAGRAMS
8.1. SCHEMATIC DIAGRAM FOR MODEL TX-29P82X
(MX-10A CHASSIS)
TX-29P82X
17

1 Safety Precautions
1.1. General Guide
1. It is advisable to insert an isolation transformer in the AC
supply before servicing a hot chassis. Fig. 1.
Fig. 1
2. When servicing, observe the original lead dress, especially
the lead dress in the high voltage circuits. If a short circuit is
found, replace all parts which have been overheated or
damaged by the short circuit.
3. After servicing, observe that all the protective devices such
as insulation barriers, insulation papers, shields, and
isolation R-C combinations, are properly installed.
4. When the receiver is not to be used for a long period of
time, unplug the power cord from the AC outlet.
5. Potential, as high as 31.7 kV is present when this receiver
is in operation. Operation of the receiver without the
receiver power supply. Servicing should not be attempted
by anyone who is not thoroughly familiar with the
precautions necessary when working on high voltage
equipment. Always discharge the anode of the picture tube
to the receiver chassis before handling the tube.
After servicing make the following leakage current checks to
prevent the customer from being exposed to shock
hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug. Fig. 2.
Fig. 2
2. Turn on the receiver’s power switch.
3. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the receiver, such as screw heads, aerials,
connectors, control shafts, etc. When the exposed metallic
part has a return path to the chassis, the reading should be
between 4M
Ω
ΩΩ
Ωand 20 MΩ
ΩΩ
Ω. When the exposed metal does
not have a return path to the chassis, the reading must be
zero.
1.3. Leakage Current Hot Check
(See Fig. 1)
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 2 kΩ, 10 W resistor in series with an exposed
metallic part on the receiver and an earth such as a water
pipe.
3. Use an AC voltmeter, with high impedance type, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point. Fig. 3.
Fig. 3
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential any point should not exceed 1.0 V rms. In the
case of a measurement being outside of the limits specified,
there is a possibility of a shock hazard, and the receiver
should be repaired and re-checked before it is returned to
the customer. Fig. 4.
Fig. 4
1.4. X-Radiation
Warning :
1. The potential sources of X-Radiation in TV sets are the EHT
section and the picture tube.
2. When using a picture tube test rig for service, ensure that
the rig is capable of handling 29.5 kV without causing X-
Radiation.
Note: It is important to use an accurate periodically calibrated
high voltage meter.
1. Set the brightness to minimum.
2. Measure the High Voltage. The meter reading should
indicate 31.0 +0.7, -1.5kV. If the meter indication is out of
tolerance, immediate service and correction is required to
prevent the possibility of premature component failure.
3. To prevent the possibility of X-Radiation, it is essential to
use the specified picture tube.
3
TX-29P82X

2 Location of Controls and Circuit Boards
2.1. REAR VIEW
2.2. LOCATION AND FUNCTION NAME OF CIRCUIT BOARD
4
TX-29P82X

3 Service Hints
3.1. HOW TO MOVE CHASSIS INTO SERVICE POSITION.
1. Remove 9 screws.
2. Draw out Main Chassis.
3. Stand the Main Chassis.
5
TX-29P82X

4 MARKET MODE FUNCTION
Outline:
MPU controls the functions switching for each ICs through IIC bus in this chassis. The following setting and adjustment can be
adjusted by remote control in Market Mode.
1. Selection of Market Mode
Adjust the VOLUME “zero” and set OFF TIMER Button to 30 min. Then, simultaneously press the RECALL Button on the
remote control and the VOLUME DOWN button - the TV set.
2. Selection of CHK Mode
Cursor moves each CHK Mode by pressing “1” or “2” of 10 key button on the remote control.
1. Option Code Setting Mode (CHK 1)
If the memory IC (IC1102) is replaced, option code should be re-memorized. Option code can be changed by pressing Volume
“+” or “-” button. To memorize, press “0” of the 10 key button.
Display Adj. Range
COLOUR SYSTEM 0~6
MX 10A OFF / ON
C4 BIT OFF / ON
NOISE MUTE OFF / ON
SPEED OFF / ON
VCR / GAME OFF / ON
YUV OFF / ON
AV3 OFF / ON
STEREO OFF / ON
GEO 0~2
SASO 0~2
TEXT OFF / ON
PANA DISPLAY OFF / ON
SOUND SYS 0~5
2. VCJ Adjustment Mode
To change the screen (item) in CHK mode, press “3” or “4” of the 10 key button. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
SUB COLOUR 00H ~ 3FH
COLOUR 0~63
RF AGC 00H ~ FFH
SECAM B-Y 00H ~ 0FH
SECAM R-Y 00H ~ 0FH
B-Y 00H ~ 0FH
R-Y 00H ~ 0FH
SUB TEXT CONT 00H ~ 3FH
SHARPNESS 0~63
SUB Y CONT 00H ~ 3FH
CONT 0~63
SUB BRIGHT 00H ~ FFH
BRIGHT 0~63
SUB NTSC-TINT 00H ~ 3FH
6
TX-29P82X

3. Pincushion Adjustment Mode
To change the screen (item) in CHK mode, press “3” or “4” of the 10 key buttons. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
PARABOLA 00H ~ 3FH
60 V-HEIGHT 00H ~ 3FH
50 V-HEIGHT 00H ~ 3FH
SUB GEO 00H ~ 3FH
GEOMAGNETIC -9 AUTO 9
V CENTER 00H ~ 07H
50Hz CENTER 00H ~ 1FH
EW-CORNER 1 00H ~ 0FH
TRAPEZOID 00H ~ 3FH
V-LINEAR 00H ~ 3FH
60 VS CORRECT 00H ~ 3FH
50 VS CORRECT 00H ~ 3FH
H-WIDTH 00H ~ 3FH
Note : Picture will be changed to one horizontal line by pressing “5” of the 10 key button in the remote control. (1 - 5).
4. White Balance Adjustment Mode
To change the screen (item) in CHK mode, press “3” or “4” of the 10 key buttons. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
B. DR 00H ~ FFH
G. DR 00H ~ FFH
SUB.BR 00H ~ FFH
BRIGHT 0~63
B - CUT 00H ~ FFH
G - CUT 00H ~ FFH
R - CUT 00H ~ FFH
7
TX-29P82X

5 ADJUSTMENT PROCEDURE
5.1. B VOLTAGE
Item/Preparation Adjustment Procedure
1. Operate the TV set.
2. Set controls : (MARKET MODE CHK 2)
Bright ............. Minimum
Contrast ......... Minimum
Volume ............. Minimum
1. Confirm that the indicated test points for the
specified voltage:
TPA 140 : 141 ± 2V
TPA 12 : 12 ± 1.0V
TPA 9 : 9 ± 1V
TPA 5 & TPA 32 : 5 ± 1V
TPA 220 : 220 ± 15V
5.2. RF AGC
Item/Preparation Adjustment Procedure
1. Receive a colour bar pattern.
2. Set the input level to 66 (+1.2) db.
(75Ωopened)
3. Connect an oscilloscope to AGC : TPA 20 with DC mode.
1. Set RF AGC Control such as to procedure a snowy picture.
2. Set RF AGC Control at the point just before the voltage at AGC :
TPA 20 begins to drop.
3. Increase the input level by 3 db and confirm that the voltage
changes.
5.3. HIGH VOLTAGE
Item/Preparation Adjustment Procedure
1. Operate the TV set.
2. Receive the crosshatch pattern.
3. Set to 0 Beam
(Screen Control : min. CONTRAST : min)
1. Connect a DC voltage meter to D850 cathode and confirm the
voltage is 141.0 ± 2.0V.
2. Connect a high voltage meter (Electrostatic Type) to an anode of
the picture tube.
3. Confirm that the high voltage is within the range of 31.0 ± 0.7V.
5.4. SUB TINT
Item/Preparation Adjustment Procedure
1. Receive a 3.58 MHz NTSC rainbow pattern
2. Connect oscilloscope to A21 pin 6.
3. Set controls:
BRT................CENTER
COLOUR........CENTER
CONTRAST....MAX
NTSC TINT.....CENTER
AI.............. ......OFF
1. Adjust Sub NTSC Tint so that the peak of level of waveform is
similar to Fig. 3
2. Receive the Rainbow pattern (3.58 MHz NTSC) on both of Main
and Sub pictures.
3. Adjust Sub NTSC Tint 2 so that the peak of level of 1.3 ± 0.5V
5.5. SUB CONTRAST
Item/Preparation Adjustment Procedure
1. Receive a colour bar pattern.
2. Connect an oscilloscope to TPA40.
3. Connect a short jumper between D11-1 and D11-2 / TPA53 and
TPA54 FBT pin 3 or TPA34 and TPA32.
4. Set controls:
Picture menu ........ Dynamic Normal
AI .................. ........... off
1. Adjust Bright Colour:
a = 2.4 ± 0.2Vp-p
2. Adjust Sub Contrast Colour:
b = 2.7 ± 0.1Vp-p
8
TX-29P82X

5.6. PAL COLOUR OUTPUT
Item/Preparation Adjustment Procedure
1. Receive PAL colour bar pattern.
2. Connect an oscilloscope probe to TPA42.
3. Connect a short jumper to FBT pin 3 or TPA34 and TPA32.
4. Set control :
Picture menu.....................DYN AMIC NORMAL
AI.............. .................. ......off
1. Adjust Bright Control.
a = 2.3 ± 0.5Vp-p
2. Adjust Sub Colour control.
3. Connect the oscilloscope probe to TPA40.
4. Connect the waveform.
b = 3.1 ± 0.5Vp-p
5.7. NTSC COLOUR OUTPUT
Item/Preparation Adjustment Procedure
1. Apply 3.58MHz NTSC Rainbow pattern.
2. Connect an oscilloscope to TPA40.
3. Connect a short jumper to FBT pin 3 or TPA34 and TPA32.
4. Set control :
Picture menu.......................DY NAMIC CONTROL
Channel Colour Set...........S TD
1. Adjust Bright Control.
a = 2.3 ± 0.2Vp-p
2. Connect the waveform.
b = 1.3 ± 0.5Vp-p
9
TX-29P82X

5.8. COLOUR PURITY
1. Set Bright and Contrast controls to their maximum
positions.
2. Operate the TV set over 15 minutes.
3. Full degauss the picture tube by using an external
degaussing coil. By rotating R-B static convergence
magnet.
4. Apply a crosshatch pattern signal and adjust roughly the
static convergence magnets.
5. Apply a green pattern signal.
6. Loosen a clamp screw for the deflection yoke and move the
deflection yoke as close to the purity magnet as possible.
7. Adjust the purity magnet so that a vertical green field is
obtained at the center of the screen.
8. Slowly press the deflection yoke and set it where a uniform
green field is obtained.
9. Adjust roughly the Low Light controls and make sure that a
uniform white field is obtained.
10. Tighten the clamp screw.
5.9. CONVERGENCE
1. Apply a crosshatch pattern signal and set Contrast control
to the maximum position.
2. Adjust Bright control to obtain a clear pattern.
3. Adjust Red and Blue line at center of the screen.
4. Adjust Red and Blue with Green line at center of the screen
by rotating (RB)-G static convergence magnet.
5. Lock convergence magnets with silicone sealer.
6. Remove the DY wedges and slightly tilt the deflection yoke
vertically.
7. Fix the deflection yoke by re-inserting the DY wedges.
8. If purity error is found, repeat “Colour Purity” adjustment.
Before Colour Purity, Convergence and White Balance adjustments are attempted, V. Center, V. Height, H. Width, H. Center and Focus
adjustments must be completed.
10
TX-29P82X

Preparation
1. Receive a colour bar signal with colour “OFF”, and operate
the TV set for more than 15 minutes.
2. Set the picture menu to “DYNAMIC NORMAL” and the AI to
off.
3. Connect an oscilloscope to TPL7 with DC mode.
4. Set the TV set to Market Mode : white balance adjustment
(CHK 3).
5. Screen VR : Min.
6. Set the data level of SUB BRIGHT, R, G, B-CUTOFF and
R, G, B-DRIVE to the table values.
Display Data Level
R-CUT OFF 63
G-CUT OFF 128
B-CUT OFF 63
R-DRIVE 128
B-DRIVE 128
SUB BRIGHT 63
Adjustment
1. Select G-CUTOFF adjustment mode and collapse vertical
scan.
2. Adjust G-CUTOFF control to become the DC=0 V to video
level at 180 V as shown in Fig. 1.
Fig. 1
3. Slowly turn the screen control clockwise until a green colour
horizontal line appears on the picture tube. This is the
setting point for the screen control.
Note:
Do not adjust the G-CUTOFF setting in the following
procedure.
4. Adjust the remaining R and B-CUTOFF controls so as to
get a white horizontal line on the screen.
5. Return to full field SCAN by pushing the position 5 key on
the remote control.
6. Adjust the R-Drive and B-Drive controls as to obtain a
uniform white on the white bar of the greyscale pattern.
7. Confirm correct B/W rendition and greyscale tracking or
repeat CUTOFF and drive control setup.
Note:
Write down the original value for each address adjustment
before adjusting anything.
8. Wedge A shown in Fig. 2 should be fixed within a range of
45° to the left of the vertical line as shown.
9. After inserting wedge A, insert wedges B, C and D.
The wedges should be set 90° apart from each other.
10. Be certain that the four wedges are firmly fixed and the
deflection yoke is tightly clamped in place otherwise the
deflection yoke may shift its position and cause a loss of
convergence and purity.
5.10. WHITE BALANCE (MARKET MODE CHK 3)
11
TX-29P82X

9 PARTS LOCATION
TX-29P82X
27

10.1. Replacement Parts List Notes
10 Replacement Parts List
29
TX-29P82X

Mechanical Parts - TX-29P82X
Ref. No. Part No. Part Name & Description Remarks
1EASG12D559A2 SPEAKER
2EASG7D507A2 TWEETER
EUR511044 REMOTE CONTROL
3KDY4UH986F1 DEFLECTION YOKE ▲
▲▲
▲
4M68LQK186XH PICTURE TUBE ▲
▲▲
▲
5TBM4G0734 MODEL NAME PLATE ▲
▲▲
▲
6TBM4G3010 PANASONIC BADGE
7TBX4G87610 POWER BUTTON
8TEK6935 DOOR SWITCH
TES4G406 COIL SPRING
THT4G1011R CRT SCREW
9TKP4G12312 REAR AV BRACKET
10 TKP4G12424-1 DOOR
11 TKU4G9412-1 BACK COVER
12 TLK4G9022T-1 ROTATION COIL ▲
▲▲
▲
13 TLK4G9048S DEGAUSSING COIL ▲
▲▲
▲
TMM4G502 RUBBER WASHER
TMM4G503 RUBBER WEDGE
NLA TNP4G107AV L BOARD ▲
▲▲
▲
NLA TNP4G108BB X BOARD ▲
▲▲
▲
NLA TNP4G115AF T BOARD ▲
▲▲
▲
NLA TNP4G118AN GM BOARD ▲
▲▲
▲
NLA TNP4G164AD A BOARD ▲
▲▲
▲
NLA TNP4G173AA H BOARD ▲
▲▲
▲
TPC4G46901 CARTON
TPD4G1079 CUSHION (TOP)
TPD4G2071 CUSHION (BOTTOM)
TPE4G14023 SET COVER
TPE4G14024 TOP COVER
TQB4G1992 FAN BAG
TSM10032-3 MAGNET
TSN63115-4 PURITY MAGNET
TSX4G111H1 AC POWER CORD
14 TXFKY01TU2S CABINET ASSY ▲
▲▲
▲
RESISTORS
R106 ERJ6GEYJ823 M 82KOHM,J,1/10W
R108 ERJ6GEYJ153 M 15KOHM,J,1/10W
R110 ERJ6GEYJ100 M 10OHM,J,1/10W
R115 ERJ6GEYJ472 M 4.7KOHM,J,1/10W
R116 ERJ6GEYJ470 M 47OHM,J,1/10W
R117 ERJ6GEYJ122 M 1.2KOHM,J,1/10W
R118 ERJ6GEYJ122 M 1.2KOHM,J,1/10W
R119 ERJ6GEYJ121 M 120OHM,J,1/10W
R120 ERJ6GEYJ682 M 6.8KOHM,J,1/10W
R121 ERJ6GEYJ222 M 2.2KOHM,J,1/10W
R125 ERJ6GEYJ222 M 2.2KOHM,J,1/10W
R126 ERJ6GEYJ122 M 1.2KOHM,J,1/10W
R127 ERJ6GEYJ103 M 10KOHM,J,1/10W
R128 ERJ6GEYJ103 M 10KOHM,J,1/10W
R140 ERJ6GEYJ391 M 390OHM,J,1/10W
R141 ERJ6GEYJ471 M 470OHM,J,1/10W
R142 ERJ6GEYJ121 M 120OHM,J,1/10W
R143 ERJ6GEYJ470 M 47OHM,J,1/10W
R150 ERJ6GEYJ563 M 56KOHM,J,1/10W
R151 ERJ6GEYJ563 M 56KOHM,J,1/10W
R160 ERJ3GEYJ332 M 3.3KOHM,J,1/16W
R161 ERJ6GEYJ331 M 330OHM,J,1/10W
R162 ERJ6GEYJ331 M 330OHM,J,1/10W
R164 ERJ6GEYJ333 M 33KOHM,J,1/10W
R166 ERJ6GEYJ153 M 15KOHM,J,1/10W
R167 ERJ6GEYJ104 M 100KOHM,J,1/10W
R180 ERJ6GEYJ103 M 10KOHM,J,1/10W
R181 ERJ6GEYJ331 M 330OHM,J,1/10W
R182 ERD25VJ331 C 330OHM,J, 1/4W
R183 ERJ6GEYJ823 M 82KOHM,J,1/10W
R184 ERJ6GEYJ103 M 10KOHM,J,1/10W
R541 ERDS2TJ331 C 330OHM,J, 1/4W
R542 ERG3FJ392H M 3.9KOHM,J, 3W
R544 ERQ3CJ122 F 1.2KOHM,J, 3W
R551 ERDS2TJ102 C 1KOHM,J, 1/4W
Ref. No. Part No. Part Name & Description Remarks
R570 ERJ6GEYJ102 M 1KOHM,J,1/10W
R571 ERJ6GEYJ273 M 27KOHM,J,1/10W
R572 ERJ6GEYJ273 M 27KOHM,J,1/10W
R573 ERJ6GEYJ274 M 270KOHM,J,1/10W
R574 ERJ6GEYJ563 M 56KOHM,J,1/10W
R575 ERJ6GEYJ104 M 100KOHM,J,1/10W
R576 ERJ6GEYJ564 M 560KOHM,J,1/10W
R584 ERJ6GEYJ272 M 2.7KOHM,J,1/10W
R585 ERJ6GEYJ392 M 3.9KOHM,J,1/10W
R586 ERJ6GEYJ153 M 15KOHM,J,1/10W
R587 ERJ6GEYJ102 M 1KOHM,J,1/10W
R588 ERJ6GEYJ513 M 51KOHM,J,1/10W
R589 ERJ6GEYJ683 M 68KOHM,J,1/10W
R608 ERJ6GEYJ101 M 100OHM,J,1/10W
R609 ERJ6GEYJ101 M 100OHM,J,1/10W
R613 ERJ6GEYJ101 M 100OHM,J,1/10W
R614 ERJ6GEYJ101 M 100OHM,J,1/10W
R615 ERJ6GEYJ101 M 100OHM,J,1/10W
R624 ERJ6GEYJ272 M 2.7KOHM,J,1/10W
R625 ERJ6GEYJ391 M 390OHM,J,1/10W
R626 ERJ6GEYJ391 M 390OHM,J,1/10W
R627 ERJ6GEYJ391 M 390OHM,J,1/10W
R635 ERJ6GEYJ224 M 220KOHM,J,1/10W
R638 ERDS1VJ271 C 270OHM,J, 1/2W
R640 ERJ6GEYJ563 M 56KOHM,J,1/10W
R641 ERJ6GEYJ223 M 22KOHM,J,1/10W
R642 ERJ6GEYJ182 M 1.8KOHM,J,1/10W
R643 ERDS2TJ471 C 470OHM,J, 1/4W
R644 ERJ6GEYJ102 M 1KOHM,J,1/10W
R648 ERJ6GEYJ181 M 180OHM,J,1/10W
R649 ERJ6GEYJ471 M 470OHM,J,1/10W
R650 ERJ6GEYJ103 M 10KOHM,J,1/10W
R651 ERJ6GEYJ103 M 10KOHM,J,1/10W
R660 ERJ6GEYJ331 M 330OHM,J,1/10W
R661 ERJ6GEYJ681 M 680OHM,J,1/10W
R665 ERJ6GEYJ822 M 8.2KOHM,J,1/10W
R700 ERQ1CJPR82S F 0.82OHM,J, 1W
R701 ERDS2TJ103 C 10KOHM,J, 1/4W
R702 ERF5ZJ121 W 120OHM,J, 5W
R703 ERDS1FJ222 C 2.2KOHM,J, 1/2W
R704 ERDS2TJ121 C 120OHM,J, 1/4W
R705 ERDS2TJ822 C 8.2KOHM,J, 1/4W
R706 ERQ14AJ4R7E F 4.7OHM,J, 1/4W
R708 ERQ1CJ151 F 150OHM,J, 1W
R709 ERQ2CJP102S F 1KOHM,J, 2W
R711 ERDS2TJ101 C 100OHM,J, 1/4W
R712 ERDS2TJ822 C 8.2KOHM,J, 1/4W
R714 ERDS2TJ272 C 2.7KOHM,J, 1/4W
R715 ERDS2TJ222 C 2.2KOHM,J, 1/4W
R716 ERDS2TJ103 C 10KOHM,J, 1/4W
R717 ERDS2TJ103 C 10KOHM,J, 1/4W
R718 ERDS2TJ103 C 10KOHM,J, 1/4W
R750 ERDS2TJ243 C 24KOHM,J, 1/4W
R751 ERD25TJ104 C 100KOHM,J, 1/4W
R752 ERDS2TJ103 C 10KOHM,J, 1/4W
R753 ERDS2TJ821 C 820OHM,J, 1/4W
R755 ER0S2CHF1503 M 150KOHM,F, 1/4W
R756 TR0S2THF1152 M11.5KOHM,F, 1/4W
R758 TAR26EJ2R7Z W 2.7OHM,J, 10W
R801 TAR26FJ2R2Z W 2.2OHM, 15W ▲
▲▲
▲
R810 ERDS1TJ394 C 390KOHM,J, 1/2W
R811 ERDS2TJ473 C 47KOHM,J, 1/4W
R814 ERF5ZJ121 W 120OHM,J, 5W
R1110 ERJ6GEYJ101 M 100OHM,J,1/10W
R1111 ERJ6GEYJ472 M 4.7KOHM,J,1/10W
R1112 ERJ6GEYJ472 M 4.7KOHM,J,1/10W
R1113 ERJ6GEYJ332 M 3.3KOHM,J,1/10W
R1114 ERJ6GEYJ332 M 3.3KOHM,J,1/10W
R1120 ERJ6GEYJ101 M 100OHM,J,1/10W
R1121 ERJ6GEYJ101 M 100OHM,J,1/10W
R1123 ERJ6GEYJ152 M 1.5KOHM,J,1/10W
R1124 ERJ6GEYJ152 M 1.5KOHM,J,1/10W
10.2. Replacement Parts List
30
TX-29P82X