Panasonic ProLine AG-1340P User manual
ORDERNO. BSD0109M021
D01
Video Cassette Recorder
AG-1340P
Z-MECHANISM
2001 Matsushita ElectricIndustrial Co., Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
Please refer to theservice manual for Z-MechanismChassis
and theOperating Instructionsin theappendixfolder. / (Go
to Appendix List)
1
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
SAFETY PRECAUTIONS
GENERALGUIDELINES
1. When servicing, observe the original lead dress. Ifashort / circuit
isfound, replace all parts which have been over-heated or
damaged bythe short circuit.
2. After servicing, see to itthat all the protective devices such as
insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to
2
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
prevent the customer from being exposed to shock hazards.
LEAKAGE CURRENTCOLD CHECK
1. Unplug the AC cord and connect ajumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohm meter, between the
jumpered AC plug and each exposed metalliccabinet part on the
equipment such as screwheads, connectors, control shafts, etc.
The resistance value must be more than 5M .
Figure1
LEAKAGE CURRENTHOTCHECK (See Figure 1)
1. Plug the AC cord directlyinto the AC outlet. / Donot use an
isolation transformer for thischeck.
2. Connect a1.5k , 10W resistor, inparallel with a0.15 F
capacitor, between each exposed metallicpart on the set an a
good earth ground such as awater pipe, as showninFigure1.
3. Use an AC voltmeter, with 1000 ohms/voltor more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallicpart, and measure the voltage at
each point.
5. Reverses the AC plug inthe AC outlet repeat each of the above
measurements.
6. The potential at anypoint shouldnot exceed 0.15 volts RMS. A
leakage current tester (Simpson Model 229 equivalent) maybe
used to make the hot checks, leakage current must not exceed 0.1
milliamp. Incase ameasurement isoutside of the limits specified,
3
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
there isapossibilityof ashock hazard, and the equipment should
be repaired and checked before itisreturned to the customer.
ELECTROSTATICALLY SENSITIVE (ES) DEVICES
Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such
components commonlyare calledElectrostaticallysensitive (ED) Devices. Examples of typical
ES devices are integratedcircuits and some field-effect transistors and semiconductor“chip”
components. The following techniques shouldbe usedtohelpreduce the incidence of
component damage causedbystatic electricity.
1. Immediatelybefore handling anysemiconductor component or
semiconductor-equipped assembly, drainoff anyelectrostatic
charge on your bodybytouching aknownearth ground. /
Alternatively, obtainand wear acommerciallyavailable
discharging wrist trap device, which shouldbe removed for
potential shock reasons prior to applying power to the unitunder
test.
2. After removing an electrical assemblyequipped with ES devices,
place the assemblyon aconductive surface such as aluminum
foil, to prevent electrostaticcharge buildup or exposure of the
assembly.
3. Use onlyagrounded tipsoldering iron to solder or unsolder ES
devices.
4. Use onlyan anti-staticsolder removal device classified as “anti-
static” can generate electrical charges sufficient to damage ES
devices.
5. Donot use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Donot remove areplacement ES device from its protective
package until immediatelybefore you are readyto install it. /
(most replacement ES devices are package with leads electrically
shorted together byconductive foam, aluminum foil or
comparableconductive material).
7. Immediatelybefore removing the protective material from the
leads of areplacement ES device, touch the protective material to
the chassisor circuitassemblyinto which the device will be
4
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
installed. / CAUTION:Besure no power isapplied to the chassis
or circuit, and observe all other safetyprecautions.
8. Minimize bodilymotions when handling unpacked replacement
ES devices. (Otherwise harmless motion such as the brushing
together of your clothes fabricor the lifting of your foot from a
carpeted floor can generate staticelectricitysufficient to damage
an ES device).
X-RADIATION
WARNING
1. The potential source of X-radiation inEVF sets isthe High Voltage
section and the picture tube.
2. When using apicture tube test jigfor service, ensure that jigis
capableof handling 10kV without causing x-radiation.
Note :
It is important touse anaccurate periodicallycalibratedhigh voltage meter.
3. Measure the High Voltage. The meter (electrictype) reading
shouldindicate 2.5kV, 0.15kV. Ifthe meter indication isout of
tolerance, immediate service and correction isrequired to prevent
the possibilityof premature component failure. To prevent an x-
radiation possibility, itisessential to use the specified picture
tube.
1. General Descriptions
2. Adjustment Procedures
3. Abbreviations
4. Input/Output Chart
5. Block Diagrams
5
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
6. Schematic Diagrams
NOTE
BE SURE TO MAKE YOUR ORDERS OFREPLACEMENTPARTS ACCORDING TO PARTS LIST.
CAUTION
THE MARK INDICATES THE PRIMARY CIRCUITTO DISTINGUISH THE PRIMARY FROM THE
SECONDARY CIRCUIT. / PAY ATTENTION NOTTO RECEIVE AN ELECTRIC SHOCK DURING
REPAIR
SERVICE OFTHE PRODUCTS.
IMPORTANTSAFETY NOTICE:
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIALCHARACTERISTICS FOR
SAFETY. / WHEN REPLACING ANY OFTHESE COMPONENTS, USE ONLY THE SAME TYPE.
6.1. POWERSECTIONINMAINSCHEMATICDIAGRAM
6.2. SYSTEM CONTROL&SERVO / TIMERSECTIONINMAIN
SCHEMATICDIAGRAM
6.3. VIDEO SECTIONINMAINSCHEMATICDIAGRAM
6.4. AUDIO SECTIONINMAINSCHEMATICDIAGRAM
7. Circuit Board Diagrams
NOTE
BE SURE TO MAKE YOUR ORDERS OFREPLACEMENTPARTS ACCORDING TO PARTS LIST.
6
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
CAUTION
THE MARK INDICATES THE PRIMARY CIRCUITTO DISTINGUISH THE PRIMARY FROM THE
SECONDARY CIRCUIT. / PAY ATTENTION NOTTO RECEIVE AN ELECTRIC SHOCK DURING
REPAIR
SERVICE OFTHE PRODUCTS.
IMPORTANTSAFETY NOTICE:
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIALCHARACTERISTICS FOR
SAFETY. / WHEN REPLACING ANY OFTHESE COMPONENTS, USE ONLY THE SAME TYPE.
7.1. MAINP.C.BOARD (VEP06E21J)
8. Mechanical Replacement Parts List & Exploded
Views
NOTE:
1. Be sure tomake yourorders of replacement parts according tothis list.
2. Unless otherwise specified, all resistors are inOHMS, K=1,000 OHMS, all capacitors are in
MICROFARADS ( F), P= F.
3. The P.C. Boarduntils markedwith" " shownbelowthe mainassembledparts.
4. The parts markedwith on the explodedviewshowthe electric parts.
5. IMPORTANTSAFETY NOTICE
Components identifiedwiththe mark have the special characteristics forsafety. When
replacing
anyof these components, use onlythe same type.
6. The marking (RTL) indicates the retention time is limitedforthis item. / Afterthe
diacontinuation
assemblyinproduction, it will no longerbe available.
7. “(M)” inRemark columnindicates neededinthe periodical maintenance.
9. Electrical Replacement Parts List
7
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
NOTE:
1. Be sure tomake yourorders of replacement parts according tothis list.
2. Unless otherwise specified, all resistors are inOHMS, K=1,000 OHMS, all capacitors are in
MICROFARADS ( F), P= F.
3. The P.C. Boarduntils markedwith" " shownbelowthe mainassembledparts.
4. The parts markedwith on the explodedviewshowthe electric parts.
5. IMPORTANTSAFETY NOTICE
Components identifiedwiththe mark have the special characteristics forsafety. When
replacing
anyof these components, use onlythe same type.
6. The marking (RTL) indicates the retention time is limitedforthis item. / Afterthe
diacontinuation
assemblyinproduction, it will no longerbe available.
NOTE:
Alist of parts isstored indata form inthe CD-ROM. Itislocated
withinthe folder APPENDIX/PARTS. Please use as necessary.
10. PDF for Printing
Setting of Acrobat Reader
To viewa link ina newwindow, followthe procedure below. Whenyou operate the PDF
documents
printing, you canopena PDFfile of eachsection while displaying the coverpage. This is
convenient
the PDFfiles inseveral sections.
<Howtoset> Inthe [File] menu, select [Preference] - [General...] and disable [OpenCross-Doc
Links
Same Window].
8
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
1.1. SERVICE CAUTION-1
When the Microprocessor IC6001 and/or Back-up battery
B6001 are replaced, read following procedure carefully and
proceed it.
[REASONS]
There is a RAM in the IC6001, which is backing up:
1.Programme Navigation Data
2.TV Tuning Data
3.PG Shifter Adjustment Data
4.Option Setting Data
When IC6001 and/or B6001 are replaced, all above listed data
become not available.
These data is backing up by using the power source of:
*AC Connected : AC Power source
*AC Disconnected : Back-up Battery (B6001)
1.1.1. REPLACING PROCEDURE
[IC6001/B6001]
[1. PREPARATION]
Before replacing IC6001 and/or B6001:
∙
Take a note that store TV broadcast channels.
(Because, its user may store TV broadcasts by manually
other than “Auto Tuning” operation and it is also erased.)
∙
Back-up the Programme Navigation data.
(The Programme Navigation data is transferable by using
“Programme Navigation Data Back-up Tool (VFK1493P)”
(You may take make it by referring following schematic
diagram.)
-NECESSARY STATUS OF THE VCR UNIT-
1.The IC6001 should be comunicable with the Programme
Navi. Back-up Tool. (VFK1493P)
2.The “NAVI” data has to be available in IC6001.
NOTE:
During servicing, do not make short IC6001-pin 37 (5V) with
other line/Components, otherwise, IC6001 may be broken.
[2. HOW TO CONFIRM THE “NAVI.” DATA WITHOUT
INSERTING A TAPE INTO VCR?]
1.Indicate the “NAVI” mark on the Front information Panel.
(Press the Menu button and select the option, then set the
“NAVI” to ON mode.)
2.Turn on the Service Mode and press the “NAVI” button on
the Remote Controller in more than 5 seconds.
The “NAVI” date list is displayed on the Monitor.
(Press the “MENU” button on the Remote Controller for
cancellation.)
[3. REPLACING PROCEDURE IN STEPS]
STEP 1. PREPARATION
1.Remove the C.B.A. with Mechanism unit by referring the
Disassembly procedure.
2.Connect the VFK1493P by referring the following figure.
1 GENERAL DESCRIPTIONS
5
AG-1340P
STEP 2. “NAVI” DATA BACK-UP
PROCEDURE F.I.P. DISPLAY
Turn on the Service Mode.
1. Press FF and EJECT keys
simultaneously for more than
3 seconds.
Turn on the Service Mode 2.
2. Press FF and EJECT keys in twice.
Turn on the Set-up mode.
3. Press the EJECT key for more than
3 seconds.
Turn on the mode 6.
4. Press the CH UP key in 3 times.
Activate the Back-up.
5. Press the FF key for more than 3
seconds.
(OK) “UP” is displayed when the Back-up
process has been done
successfully.
(NG) “31” is displayed when the Back-up
process has not been done
successfully.
(“31” is displayed mainly when the connection failure and ROM
failure of VFK1493P occurred. Confirm them and try again.)
STEP 3. REPLACE THE IC6001 AND/OR B6001
1.Disconnect the AC plug and replace the IC6001 and/or
B6001. (Do not make a short circuit between IC6001-pin 37
and other pins/components.)
CAUTION:
*When replacing the B6001, be sure to read/follow the
“HOW TO REPLACE THE LITHUM BATTERY” section.
STEP 4. RESET THE IC6001 AT ONCE
1.Connect the AC plug.
2.Connect a jumper wire between TL7510 and TW6090
(GND) for a second to reset the Microprocessor IC6001.
Note:
Since the resistance at pin 1 as well as pin 2 of IC6001
decides the model distinction data, no need to set up the
Model code, which is necessary in previous model.
STEP 5. LINE INPUT SETTING
1.Connect the 1.5 V battery to TL6010 or Pin 6 of IC6001 until
the FIP displays unreadable irregular characters.
2.Disconnect the AC plug for few seconds and connect it
again.
3.Confirm that “A1” and “A2” can be displayed on the FIP by
pressing the CH UP and CH DOWN buttons.
Note:
1.To set-up the “Plug in Auto Tuner Preset”, press the
Channel up and down keys simultaneously for 3
seconds.
2.Change the OSD setting to the Factory shipping
condition if necessary, by referring following charts.
STEP 6. NAVI. DATA WRITING/SAVING
1.Connect the Prog. Navi. Data Back-up Tool (VFK1493P)
PROCEDURE F.I.P. DISPLAY
Turn on the Service Mode.
1. Press FF and EJECT keys
simultaneously for more than
3 seconds.
Turn on the Service Mode 2.
2. Press FF and EJECT keys in twice.
Turn on the Back-up mode.
3. Press the EJECT key in more than
3 seconds.
Turn on the Back-up mode 6.
4. Press the CH UP key for 3 times.
Activate the NAVI. Data Writing.
5. Press the REW key in more than 3
seconds.
(OK) “dn” is displayed when the Back-up
process has been done
successfully.
(NG) “32” is displayed when the Back-up
process has not been done
successfully.
(“32” is displayed mainly when the connection failure and ROM
failure of VFK1493P occured. Confirm them and try again.)
Reset the Service Mode. Normal Indication
6. Press FF and EJECT keys
simultaneously in 6 times.
NOTE: Perform the PG SHIFTER ADJUSTMENT.
6
AG-1340P
1.2.1. GERNERAL DESCRIPTION
There is a RAM in the IC6001, which is backing up the following
data by using the power source of B6001 (Back-up Battery).
1.Programme Navigation Data
2.TV Tuning Data
3.PG Shifter Adjustment Data
4.Option Setting Data
1.2.2. REPLACEMENT PROCEDURE
1.Remove the Top Panel and Mechanism unit with Main
C.B.A. by referring the Disassembling Procedure.
2.Unsolder the Lithium Battery: B6001 “CR2354-1GUF” and
then replace it into new one. (See Fig.B1) Fig.B1
1.2. HOW TO REPLACE THE LITHIUM BATTERY
NOTE:
The lithium battery is a critical component (Type No.:CR2354-1GUF Manufactured by Panasonic.)
It must nerver be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battey, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposeed of in waste products destined for burial rather than incineration.
7
AG-1340P
1.3. SERVICE CAUTION-2
1.3.1. CAUTION FOR AUTO TUNING
PROCEDURE
Auto Tuning will start by the following procedure.
1.Connect the DIN-RF Cable.
2.Connect the AC Mains Lead.
3.Turn on the VCR.
Auto Tuning will start.
Auto Tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned program
position. Other program positions are skipped.
Auto Tuning takes five or more minutes to complete its
search.
Do not touch the VCR during Auto Tuning.
Auto Tuning will stop halfway, if the VCR is operated or
the aerial lead and/or the mains lead are disconnected.
In case the VCR stopped during Auto Tuning, the VCR
have to be reset and restarted. See the following item 2.
NOTE
1.If the VCR is turned on with the antenna not connected,
all channels are skipped. Therefore, firmly connect the
antenna and then turn the VCR off and on again to
execute Auto tuning.
2.
When Auto Tuning is canceled halfway, Auto Tuning
is not executed even if the VCR is turned off and
then turned on again.
In this case, Auto Tuning have to be restarted by the
following procedure.
a.
Press EJECT and remove the Video cassette.
b.
Keep UP and DOWN on the VCR pressed
simultaneously for 3 seconds or more during the
VCR on.
The channel displayed on the VCR display
disappears for a moment then changes to 2.
c.
Turn off the VCR and then turn it on. Auto Tuning
commences.
3.If you turn the VCR off during Auto Tuning, Auto Tuning
will stop halfway.
The VCR should be reset and restarted by the item 2 in
order to execute Auto Tuning.
4.If the VCR starts playback during Auto Tuning, Auto
Tuning will stop halfway.
The VCR should be reset and restarted by the item 2 in
order to execute Auto Tuning.
5.To cancel Auto Tuning Mid-operation, press POWER
during Auto Tuning (The VCR is turned off).
6.When the VCR is moved to the other area or country,
TV broadcasts should be stored again.
1.3.2. CHECKING OF MAIN C.B.A.
When servicing the MAIN C.B.A., take out the MAIN C.B.A. and
mechanism from the frame and turn over.
Fig. S3
1.3.3. REMOVAL OF CASSETTE TAPE
There are 2 ways to remove a cassette tape.
1.Removal of compulsory loading.
a.Press FF and EJECT buttons simultaneously and set
the Service Mode 7.
b.Press STOP button in order to unload the mechanism.
(Pay an attention of tape slack)
Service Mode Indication:
7****(STOP)→7 00 ** (EJECT)
2.Removal of manual operation of Main cam gear.
a.Disconnect the AC power cord and remove Top Panel.
b.Rotate Main Cam Gear to the clockwise and unload the
mechanism (Tape is remaining) (Fig. S4).
Fig. S4
c.Rotate the Pole of Capstan motor to the clockwise the
from the bottom in order to remove the tape slag.
8
AG-1340P
Fig. S5
d.Rotate Main Cam Gear to the clockwise in order to eject
the cassette tape.
1.3.4. CYLINDER UNIT REPLACEMENT
1.CYLINDER UNIT REPLACEMENT
a.Remove the Mechanism unit from MAIN C.B.A./Chassis
by referring “Disassembly Procedure”.
b.Remove the 3 screws (A) of the CYLINDER UNIT with
a screw driver.
c.Unlock the 4 locking tabs (B) and disconnect the
Cylinder flexible card from the FPC Holder.
d.Remove the CYLINDER UNIT.
CAUTION
Handle the Cylinder flexible card with care. When it
damaged, you should replace whole Cylinder unit.
Fig. S6
2.UPPER CYLINDER DISASSEMBLY
a.Remove 2 screws (A).
b.Remove the Cylinder Stator Unit.
c.Remove 2 screws (B).
d.Remove the Cylinder Rotor Unit.
e.Loose Hex screw (C) (1.5 mm) and remove the
CYLINDER RETAINER.
f.Remove the Upper Cylinder.
Fig. S7
3.UPPER CYLINDER ASSEMBLY
When reassembling, perform the steps in the reverse order.
Notes:
a.Install the Cylinder Retainer so that the 2 holes on top of
the Cylinder Retainer are at right angles with the P5001
Connection.
b.Tighten the Hex screw (C) (1.5 mm) while pressing
down on top of the Cylinder Retainer.
9
AG-1340P
Fig. S8
c.Install the Cylinder Rotor Unit so that the inner hole of
the Cylinder Rotor Unit fits to the small projection (D) on
top of the Upper Cylinder.
d.Tighten 2 screws (B).
Fig. S9
e.Install the Cylinder Stator Unit.
f.Tighten 2 screws (A).
Fig. S10
g.Confirm the PG SHIFTER ADJUSTMENT with the
alignment tape (NTSC: VFM8080HQFP) and adjust it if
necessary.
1.3.5. FLAT CARD CABLE
INSTALLATION
When installing the Flat Card Cable on the connector, install
the Flat Card Cable with the cable contacts facing the
connector contacts.
Fig. S11
1.4. SELF-TEST & SERVICE
INFORMATION DISPLAY
Refer to the Service Manual for Z Mechanism Chassis. (Order
No.:VRD9802005C2)
10
AG-1340P
4 INPUT/OUTPUT CHART
4.1. INPUT/OUTPUT CHART FOR IC6001
19
AG-1340P
20
AG-1340P
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
VFM8080HQFP VHS ALIGNMENT TAPE 1
VFK0335 RETAINING RING REMOVER 1
VFK0329 POST ADJ. SCREWDRIVER 1
VFK0326 HEX WRENCH SET 1
VFK0132A BACK TENSION METER 1
VFK27 HEAD CLEANING STICK 1
M0R265 MORLYTONE GREASE 1
VFK0330 FINE ADJ. SCREWDRIVER 1
VFK1301 SILICONE GREASE 1
VFK1298 FOIL GREASE 1
SERVICING FIXTURES & TOOLS
8 EXPLODED VIEWS & REPLACEMENT PARTS LIST
PRT-1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
N1 VHN0311 PUSH NUT 1
1 VEG1537 CYLINDER UNIT 1
2 VXP2026 UPPER CYLINDER UNIT 1 SUPPLIED FROM MAV W1 VMX2208 CUT WASHER 1
3 VDB1256 CYLINDER RETAINER 1 W2,W3 VMX3022 WASHER 2
4 VEK8840 CYLINDER MOTOR UNIT 1
6 VXS0135 EARTH BRUSH ASS'Y 1
10 VEK9069 CAPSTAN ASS'Y 1
11 L1AZ00000004 FE HEAD 1
12 VDB1431 TENSION ARM BOSS 1
13 VDB1460 SUPPLY BRAKE ARM BOSS 1
14 VDG1220KIT MAIN CAM GEAR 1
15 VDG1221 CONVERSION GEAR 1
16,17 VDR0350 REEL TABLE 2
18 VDV0382 CAPSTAN BELT 1
19 VED0412 A/C HEAD ASS'Y 1
20 VMX2656 P4 CAP 1
21 VDG1217 WORM GEAR 1
22 VDG1218 WORM WHEEL GEAR 1
23 VDG1219 CENTRE GEAR 1
24 VEM0604 LOADING MOTOR ASS'Y 1
25 VMD2619 MOTOR BRACKET 1
26 VMB3045 CONVERSION GEAR SPRING 1
27 VMD2620 OPENER PIECE 1
28 VMD2738 LED PRISM 1
29 VML3165 DRIVE RACK ARM 1
30 VML3166 MAIN LEVER 1
31 VML3167 DRIVE MAIN LEVER ARM 1
32 VML3172 SUPPLY SPRING ARM 1
33 VML3176 CONVERSION LEVER A 1
34 VML3177 CONVERSION LEVER B 1
35 VXA6040 INCLINED BASE (S) ASS'Y 1
36 VXA5854 INCLINED BASE (T) ASS'Y 1
37,38 VXP1891 ROLLER POST ASS'Y 2
39 VMA9672 SUPPORT ANGLE 1
41 VXL2667 TAKE UP BRAKE ARM ASS'Y 1
43 VXL2670 TAKE UP LOADING ARM ASS'Y 1
44 VXL2793 TENSION ARM ASS'Y 1
45 VXL2672 SUPPLY LOADING ARM ASS'Y 1
46 VXL2785 PINCH ARM ASS'Y 1
47 VXL2996 P5 ARM ASS'Y 1
48 VXL2792 IDLER ARM ASS'Y 1
49 VXL2733 SUPPLY BRAKE ARM ASS'Y 1
50 VML2747 LOADING RACK ASS'Y 1
51 VXP2035 CENTER CLUTCH ASS'Y 1
60 VMA9516 TOP PLATE 1
61 VMB3047 CONNECTION SPRING 1
62 VMD3379 SIDE PLATE (L) 1
63 VXA6540 SIDE PLATE (R) ASS'Y 1
64 VXA5746 CASSETTE HOLDER ASS'Y 1
65 VXP1730 MAIN SHAFT ASS'Y 1
70 VDP1668-K CLEANER ROLLER 1
71 VML3164 CLEANER ARM 1
72 VMD3795 FPC HOLDER 1
B1 VHD1118 SCREW 1
B2 VHD0842 SCREW 1
B3 VHD0843 SCREW 1
B4 VHD0844 SCREW 1
B5 VHD1118 SCREW 1
B6 VHD1066 SCREW 1
B7 VHD1044 SCREW 1
B8 VHD1060 SCREW 1
B9 VHD1071 SCREW 1
B10 VHD0843 SCREW 1
B11 XTS26+6F SCREW 1
B12 XTN26+6F SCREW 1
B13 XTN26+7J SCREW 1
B14 VHD1095 SCREW 1
B15 VHD1185 SCREW 1
B16 VHD0844 SCREW 1
B17 VHD1066 SCREW 1
B18,19 XTN26+7J SCREW 2
CHASSIS PARTS SECTION
PRT-3
Table of contents
Other Panasonic VCR System manuals
Panasonic
Panasonic NV-HS860EE User manual
Panasonic
Panasonic Omnivision PV-V4611 User manual
Panasonic
Panasonic Omnivision PV-4614 User manual
Panasonic
Panasonic AGDTL1P - TIME LAPSE RECORDER User manual
Panasonic
Panasonic Omnivision PV-M1349 User manual
Panasonic
Panasonic NV-HV62GH User manual
Panasonic
Panasonic Omnivision PV-V4020 User manual
Panasonic
Panasonic NV-SJ5MK2AM User manual
Panasonic
Panasonic NV-SV121 Series User manual
Panasonic
Panasonic NV-SD10 Series User manual
Panasonic
Panasonic AJ-HD2000 User manual
Panasonic
Panasonic PV-V4623S-K User manual
Panasonic
Panasonic Quasar W-1301 User manual
Panasonic
Panasonic AG-1330 User manual
Panasonic
Panasonic AGRT650P - TIME LAPSE VTR User manual
Panasonic
Panasonic AJ-HD150 User manual
Panasonic
Panasonic NV-SJ500 Series User manual
Panasonic
Panasonic NV-SJ422EE User manual
Panasonic
Panasonic Omnivision PV-V4540 User manual
Panasonic
Panasonic NV-W1E User manual
