Paramount Fitness Paralevel User manual

Paramount
8175 W. Buckeye Rd.,
Phoenix, AZ 85043
Phone: [phone]
www.1Paramount.com
Paralevel
Float Assembly Seal Replacement Kit
Installation Manual
Contents
Overview.................................1
Installation.............................1
Operation...............................5
004-027-8883-00 R00
ECN_2363 PUB030823
005-762-2932-00
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Overview
Installation
Follow the steps below to install the Paralevel float assembly kit.
1. Turn off the water supply to the Paralevel. Remove the Paralevel float assembly by grasping
the top of the float assembly and while pushing down turn the assembly counter clockwise a
quarter turn. The float assembly should then pull out.
Paralevel float assembly kit
005-762-2932-00
What's Included
• Lever assembly
• White o-ring
• Black o-ring - replace if necessary
Push down and twist
counter clockwise
Lift up to remove
1
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

2. There is a white o-ring seal at the bottom
end of the float assembly. Peel off to remove.
Slide a new white o-ring over the end and
into the groove to replace.
3. Next, spread the retainer ring at the bottom
end to remove it from the groove and slide it
to the bottom of the shaft.
4. At the top end of the float assembly, grab the
forked link lever and pivot it down and back
gently until it pulls free from the snap swivel
point.
White
o-ring
seal
Spread
retainer
ring
Release
link
lever
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS
22

5. Grab the top cap seal arm and twist away from the snap swivel that has the opening in it. Pull
the top cap seal arm out of the top of the float assembly.
6. Reinstall the new components by reversing this process.
7. Confirm the new seal lever assembly moves freely. Then push the retainer ring on the bottom
of the assembly back into the groove.
Twist top cap
seal arm away
from snap
swivel with the
opening.
Pull out of
the float
assembly.
New seal lever
moves freely.
Push retainer
ring back into
the groove.
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS
3
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

8. Re-installing float assembly:
• Start with float ¼ down from the top on sleeve adjuster.
• Position the end of the riser tube with the o-ring inside the opening at the top of the nut
retainer.
• Turn the riser tube clockwise and wiggle until it drops into the nut retainer. Too much
downward pressure before it sets into the opening of the nut retainer will cause the float
assembly to hang up.
• Press down on the top of the riser tube and twist clockwise ¼ turn or until it stops.
Float is ¼ down
from top on
sleeve adjuster.
Drop into nut retainer.
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS
4
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Operation
Adjusting water level
Water level adjustment procedure (standard 3” water-
line below beam):
• Adjust the pool water level to the desired point on
the tile line.
• Turn on water supply at source fully.
• Start with the float high and the leveler allowing
water to flow.
• Turn the float clockwise 1/2 turns at a time until
the Paralevel shuts off.
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS
5
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS
6
USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

For further information or consumer
technical support, visit our website at
www.1Paramount.com
Paralevel is a registered trademark
of Hayward Industries, Inc. © 2023 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners. Hayward is not in any way
affiliated with or endorsed by those third parties. For patent information, refer to www.hayward.com/patents.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS