Parkside PSZ 250 A2 User manual

GB/
IE
7
Table of contents: Page
1. Introduction .............................................................................8
2. Safety information...................................................................8
3. Layout and items supplied .....................................................8
4. Proper use ..............................................................................8
5. Technical data ........................................................................9
6. Before putting the machine into operation ..............................9
7. Mounting and assembly .........................................................9-10
8. Cleaning, maintenance and ordering of spare parts...............10
9. Disposal and recycling............................................................10
10. Guarantee Certificate .............................................................11
The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers accompanying products is
permitted only with the express consent of ISC
GmbH. Technical changes subject to change
Anleitung_LB6_2255414:_ 01.06.2011 17:24 Uhr Seite 7

8
1. Introduction
Important!
When using equipment, a few safety
precautions must be observed to avoid injuries
and damage. Please read the complete
operating manual with due care. Keep this
manual in a safe place, so that the information
is available at all times. If you give the
equipment to any other person, give them
these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these
instructions and the safety information.
2. Safety information
Ensure that you observe the following points in
order to avoid accidents and injuries.
Do not overload your swing arm.
Do not continue to use the swing arm if it is
damaged.
Ensure that all bolts are tightly fastened
and check them frequently for your own
safety.
Ensure that the cotter pin is properly
inserted through the bore holes.
Lifting and carrying persons with the cable
winch is strictly prohibited! Additionally,
persons may not loiter underneath the
cable winch/swing arm assembly.
Persons who are not aware of these safety
precautions may not use this product.
All components must be regularly checked for
any kind of deformation or damage.
Observe the maximum permissible load
capacity (see „Technical Data“)!
3. Layout and items supplied
(Fig. 1/2)
1. Pipe collar (with large hinge pin A)
2. 2x holding bars for pipe collars
3. Pipe collar (with small hinge pin B)
4. Support arm
5. Square-edged boom 45 x 45 x 1.8 mm
6. Extension pipe 40 x 40 x 2.5 mm
7. Cotter pin Ø 3 x 45 mm
8. Cotter pin Ø 3 x 60 mm
9. 4x hexagon nuts M10
10. 4x spring washers Ø 10
11. 4x washers Ø 10
12. 2x pads for clamping brackets
13. Hexagon nut M8
14. Spring washer Ø 8
15. Washer Ø 8
16. Hexagon bolt M8 x 15 mm
17. Hexagon bolt M12 x 70 mm
18. Hexagon nut M12
19. Spring washer Ø 12
20. Washer Ø 12
4. Proper use
The swing arm is designed to be attached to a
cable winch. For this, the swing arm must be
mounted to a well fastened steel bar with a
diameter of 48 mm.
The machine is to be used only for its
prescribed purpose. Any other use is deemed
to be a case of misuse. The user / operator
and not the manufacturer will be liable for any
damage or injuries of any kind caused as a
result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the machine is used in commercial,
trade or industrial businesses or for equivalent
purposes.
GB/
IE
Anleitung_LB6_2255414:_ 01.06.2011 17:24 Uhr Seite 8

GB/
IE
9
5. Technical data
Reach l: Max. load:
l1= 750 mm m1= 600 kg
l2= 1100 mm m2= 300 kg
Swing range: max. 180°
6. Before putting the machine
into operation
The swing arm is designed to take a cable
winch.
To mount the swing arm, you need a round
steel bar with a diameter of Ø 48 mm; its
wall must be a minimum of 3 mm thick.
Ensure that the anchor points of the steel
bar are able to adequately support the
forces that will be applied to it. Consult an
authorized professional to ensure that this
is properly done. This steel bar is not
included in the scope of delivery.
7. Mounting and assembly
Attach the pipe collar (1) (with the large
hinge pin (A)) to a steel bar using the
holding bar for the pipe collar (2), washers
(11), spring washers (10) and two hexagon
nuts (9). Before you tighten the bolts, push
the pipe collars (1) to the desired working
height of the swing arm (Figure 3-5).
Apply lubricating grease to the hinge pin
(A).
Slide the square-edged boom (5) over the
hinge pin (A) and push the cotter pin (8)
through the hole in the hinge pin (A) (Figure
6-7).
Finally, bend apart the two shanks of the
cotter pin (8) so that the cotter pin (8)
cannot work its way out of the bore hole.
(Figure 8)
Now attach the pipe collar (3) (with the
small hinge pin (B)) to the steel bar above
the square-edged boom in the same way
as you did with pipe collar (1). Adjust the
height of the upper pipe collar (3) so that
the distance H between the two pipe collars
(1/3) measures exactly 380 mm.
Slide the support arm (4) with the larger
bore hole over the hinge pin (B) of the pipe
collar (3). Push the cotter pin (7) into the
bore hole of the hinge pin (B) and bend
apart the two shanks of the cotter pin (7) so
that the cotter pin (7) cannot work its way
out of the bore hole (Figure 9-10).
Now tighten the bolts of the pipe collars.
Use a torque of 45 Nm to tighten the nuts
(9).
Push the extension pipe (6) by its end with
no bore hole into the square-edged boom
(5) (Figure 11). Make sure that the bore
hole (C) is on the outside as shown in
Figure 12.
Connect the support arm (4) to the square-
edged boom (5) and the extension pipe (6)
by inserting the hexagon bolt (17) through
the coinciding bore holes, placing a washer
(20) and a spring washer (19) over the bolt
(17), and securing the connection with a
hexagon nut (18) (Figure 12-14).
A bolt (16) is inserted at the end of the
extension pipe to prevent the cable winch
from sliding off (Figure 15-17).
When the cable winch is pushed out to 750
mm, it is not allowed to lift more than 600
kg (Figure 18).
When the cable winch is pushed out to
1100 mm, it is not allowed to lift more than
300 kg (Figure 20).
When mounting the cable winch on the
extension pipe (6), the pads (12) must be
pushed in under the clamping brackets in
order to ensure that the cable winch is held
securely in place (Figure 19). When the
assembly work is finished, an up and down
Anleitung_LB6_2255414:_ 01.06.2011 17:24 Uhr Seite 9

GB/
IE
10
test and a 180° left and right swing test
must each be performed twice with no load.
Then the cable winch must be loaded with
increasingly heavier loads up to the
maximum permissible load weight. Only
when the cable winch has passed these
tests are you allowed to use the equipment
for normal operations.
8. Cleaning, maintenance and
ordering of spare parts
8.1 Cleaning and maintenance
Regularly clean the swing arm and lubricate
the hinge pins (A/B).
8.2 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
For our latest prices and information please go
to www.isc-gmbh.info
9. Disposal and recycling
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is
raw material and can therefore be reused or
can be returned to the raw material system.
The unit and its accessories are made of
various types of material, such as metal and
plastic. Defective components must be
disposed of as special waste. Ask your dealer
or your local council.
Anleitung_LB6_2255414:_ 01.06.2011 17:24 Uhr Seite 10