Pass HPA-1 User manual

pass®
HPA-1 High Bias Headphone Ampli•er

WARNING
For your protection please read the following:
Water and moisture: Electrical devices should not be used near water ( as per example, near a
bathtub, washbasin, kitchen sink, laundry tub, wet basement or swimming pool ). Care should
be taken such that objects do not have the opportunity to fall, and that liquid is never spilled
onto or into the device enclosure through openings.
Power Sources: An electrical device must be connected to a mains power source in strict
accordance with the supplied product owners manual. Please verify that the AC mains voltage
speci!ed in the product manual matches those requirements indicated on the unit and the AC
voltage provided to your location by the power company.
Grounding: Adequate precautions should be taken so that the grounding provisions built into
an electrical product are never defeated.
Power Cords: Pass Labs provides a power supply cord that meets all legislated requirements for
the market in which the product was originally sold. If you choose to substitute an after-market
product we urge you to choose one that is fully safety rated by the necessary local authority.
Power Cord Protection: Power supply cords should be routed so that they are not likely to be
walked on, abraded, or pinched by items placed on or against them, paying particular attention to
cords where they enter plugs or exit from a device. Never under any circumstance insert a cut or
damaged power cord into a mains power socket.
Power and Signal: Cables should never be connected / disconnected with equipment powered
up. Failure to heed this warning may damage or destroy equipment.
Ventilation: Power-ampli!ers run hot, but you should be able to place your hands on them
without discomfort. You must allow for this heat in installation, by providing for free air circu-
lation around the product. Electronics should not be subjected to sources of excessive radiant
heat. Excessive heat can shorten the life of the product and may cause the electronics to self
protect and shut down.
Servicing: To reduce the risk of !re, electrical shock or other injuries, the user should not
attempt to service the device beyond that which is described in the operating instructions. All
other servicing must be referred to quali!ed service personnel.
For Units With Externally Accessible Fuse Receptacle: Unplug the device from all sources of
power before changing or inspecting any fuse. Replace fuse with one of same physical size,
type and rating as that speci!ed by the manufacturer for that product.

1 2 3 4
1) Input Selection. 2) Preamp Out 3) Headphone Jack 4) Volume
1) AC Power Switch 2) Fuse 3) Preamp Outputs 4) Inupts
1 2 3 4

Basic Operation
The unit is designed to stay on at all times. The power switch is located in the rear.
When the power is turned on the unit goes into a mute state for twenty seconds, this is to
allow the circuitry to stabilize. During this period no functions are available. During the mute
period the power led will flash. When the unit goes out of mute into operate mode the pow-
er led will stop flashing and stay on.
The unit has two inputs that can be selected from the front panel.
The unit also has a preamp function, which is selected from the button on the front panel.
When the preamp function is engaged the headphone output is disconnected, only one out-
put either headphone or preamp is available at any one time.
The unit gets to optimum performance after about one hour after turn on.
In the event of a power loss the unit shuts off and upon restoration of power the unit will
go through the mute cycle and return to the state it was in prior to the loss of power. It will
remember the last input and function and will return to that setting before the loss of power.
This is also true when the unit is switched off with the power switch.
It is recommended that the unit stay on at all times, if you are away for an extended period
of time you could shut the unit off.
Features
Works with headphones with impedances of 15 ohms to 600 ohms
Designed as a power amplifier rather than a typical headphone amplifier to be able to drive
low impedance planar headphones.
Low feedback wide bandwidth discreet design.
Class A direct coupled Mosfet output stage
Custom low noise Torodial power transformer with a Farady shield.
Discreet regulated power supply for audio circuits.

Warranty:
Please check with the factory authorized distributor in the country where you are purchasing
this product for speci•c warranty information.
All Pass Laboratories products purchased new from an authorized Pass Laboratories dealer in
North America are covered by a transferable, limited 3-year warranty. This warranty includes all
parts and labor charges incurred at the factory or factory speci•ed repair facility, exclusive of
any subsequent or consequential damages. Damage due to physical abuse is speci•cally exclud-
ed under this warranty.
For this warranty to apply the customer is responsible for returning the product unmodi•ed to
the factory within the speci•ed warranty period. The customer assumes all responsibility for
shipping and insurance to and from the factory or a factory speci•ed repair facility. The con-
ditions and stipulations of this Pass Laboratories warranty only applies to units originally sold
new through an authorized dealer. Warranty on factory repair is 60 days and covers only the
scope of the original repair.
Non-North America customers should consult with their original Pass Labs dealer or distrib-
utor for warranty repair instruction prior to contacting the factory or shipping product to the
factory for repair.
Non-North American product must be returned to the country of origin for warranty service.
Foreign distributors are only required to offer warranty service on Pass Laboratories product
that they have imported, veri•able by serial number.
Please note: Conditions of warranty service and customer rights for product purchased outside
the United States may vary depending upon the distributor and local laws. Please check with
your local distributor for speci•c rights and details.
Any modi•cations to Pass Laboratories products that have not received written factory approv-
al nullify all claims and void all provisions of the warranty and liability by the maker or autho-
rized distributor. Should a modi•ed product be returned to the factory for repair the owner will
be required to pay all necessary charges for the repair in addition to those charges required to
return the product to it’s original con•guration.
In the case of safety issues, no product shall be returned to the customer without those safety
issues being corrected to the most recent accepted standards.
Removal or alteration of original Pass Labs serial numbers voids the factory warranty. Product
with altered or missing serial numbers will be suspect as counterfeit or stolen product.
Pass Laboratories will not repair or in any way indemnify any counterfeit or cloned product.
Pass Laboratories does not offer products in voltages intended for international markets either
to authorized Pass Labs dealers or to third parties located in the United States or Canada.

Pass HPA-1 Specs:
Output Power into 20 ohms 3500mW
Output Power into 300 ohms 200 mW
Frequency Response 10hz -100k -1dB
Gain 8 dB
THD + Noise < 0.005 at 1V out
Input Impedance 50K Ohm
Output Impedance < 2 ohms
Power Consumption 6 Watts