PC Partner 35-AA09 0 Series Use and care manual

1
Electronic Emission NoticesElectronic Emission Notices
Electronic Emission NoticesElectronic Emission Notices
Electronic Emission Notices
Federal Communications Commission (FCC) StatementFederal Communications Commission (FCC) Statement
Federal Communications Commission (FCC) StatementFederal Communications Commission (FCC) Statement
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- REORIENTORRELOCATETHERECEIVINGANTENNA
- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER
- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM
THATOFTHERECEIVER
- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISIONTECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result in
harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to operate
this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
CopyrightCopyright
CopyrightCopyright
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be
copied or reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility
for errors or omissions is assumed. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
TrademarksTrademarks
TrademarksTrademarks
Trademarks
All brand names, logos and registered trademarks mentioned are property of their
respective owners.

2
Technical Reference Booklet
TT
TT
Table of Contentsable of Contents
able of Contentsable of Contents
able of Contents
HARDWARE CONFIGURATIONHARDWARE CONFIGURATION
HARDWARE CONFIGURATIONHARDWARE CONFIGURATION
HARDWARE CONFIGURATION ..............................................................................................................
..............................................................................................................
....................................................... 44
44
4
Key Features..................................................................................................4
MOTHERBOARD LAYOUTMOTHERBOARD LAYOUT
MOTHERBOARD LAYOUTMOTHERBOARD LAYOUT
MOTHERBOARD LAYOUT ................................................................................................................................
................................................................................................................................
................................................................ 77
77
7
REAR PREAR P
REAR PREAR P
REAR PANELANEL
ANELANEL
ANEL ........................................................................................................................................................................
........................................................................................................................................................................
.................................................................................... 88
88
8
CONNECTORSCONNECTORS
CONNECTORSCONNECTORS
CONNECTORS ..................................................................................................................................................................
..................................................................................................................................................................
................................................................................. 1010
1010
10
Floppy Disk Drive Connector:CN3......................................................... 10
Hard Disk Connector:CN1&CN2........................................................... 10
SerialATAHard DiskConnector:SATA-1/SATA-2 ................................... 11
S-Bracket (SPDIF)/LEN/LFE/Surround Output Connector:
CN55(optional)..................................................................................................13
IEEE1394Connectors:CN53,CN54(optional)............................................ 15
FanPowerConnectors: CPUFAN/SYSFAN.................................................17
CD-IN Connectors:CDS1 ...................................................................... 18
AUX-IN Connector.................................................................................. 18
Front Panel Audio Header:FP_S ........................................................... 19
USB Connectors:FP_U1/FP_U2/FP_U3 ............................................... 20
Front Panel Headers:FP1...................................................................... 21
JUMPER SETTING ............................................................................ 22
CMOS Clear Jumper: JP2 ..................................................................... 22
Keyboard Power Select Jumper: JP10.................................................. 22
CPU Frequency Jumper: JP1 ................................................................ 23

3
SLOTSSLOTS
SLOTSSLOTS
SLOTS ............................................................................................................................................................................................
............................................................................................................................................................................................
.............................................................................................. 2424
2424
24
CPU INSTALLATIONCPU INSTALLATION
CPU INSTALLATIONCPU INSTALLATION
CPU INSTALLATION ................................................................................................................................................
................................................................................................................................................
........................................................................ 2525
2525
25
INSTALL DDR DIMMINSTALL DDR DIMM
INSTALL DDR DIMMINSTALL DDR DIMM
INSTALL DDR DIMMss
ss
s............................................................................................................................................
............................................................................................................................................
...................................................................... 2828
2828
28
MEMORY CONFIGURATIONSMEMORY CONFIGURATIONS
MEMORY CONFIGURATIONSMEMORY CONFIGURATIONS
MEMORY CONFIGURATIONS ....................................................................................................................
....................................................................................................................
.......................................................... 2929
2929
29
Single Channel Mode ............................................................................ 29
Dual Channel Mode............................................................................... 30
BIOS SETUPBIOS SETUP
BIOS SETUPBIOS SETUP
BIOS SETUP ..........................................................................................................................................................................
..........................................................................................................................................................................
..................................................................................... 3131
3131
31
Starting Setup ........................................................................................ 31
Main Menu.............................................................................................. 32
Standard CMOS Features ..................................................................... 33
Advanced BIOS Features....................................................................... 34
Advanced Chipset Features .................................................................. 34
Integrated Peripherals ........................................................................... 34
Power Management Setup .................................................................... 34
PNP/PCI Configurations........................................................................ 34
PC Health Status ................................................................................... 34
Frequency/Voltage Control..................................................................... 34
Set Supervisor/User Password............................................................. 35
Flash Update Procedure ....................................................................... 36
APPENDIXAPPENDIX
APPENDIXAPPENDIX
APPENDIX ..............................................................................................................................................................................
..............................................................................................................................................................................
....................................................................................... 3636
3636
36

4
Technical Reference Booklet
HARDHARD
HARDHARD
HARDWW
WW
WARE CONFIGURAARE CONFIGURA
ARE CONFIGURAARE CONFIGURA
ARE CONFIGURATIONTION
TIONTION
TION
KeyKey
KeyKey
Key FeaturesFeatures
FeaturesFeatures
Features ::
::
:
ChipsetChipset
ChipsetChipset
Chipset
• Intel® 865G/865PE/865P Chipset.
ProcessorProcessor
ProcessorProcessor
Processor
• Supports the Intel® Celeron, Northwood and Prescott processors in
the 478-pin package (with 0.8V~1.6V voltage).
• Supports 64-bit PSB (Processor System Bus) frequency of 400MHz
(100MHz bus clock), 533MHz (133MHz bus clock)
• Supports 64-bit PSB (Processor System Bus) frequency of 800MHz
(200MHz bus clock) (only for 865G/865PE).
VRM 10.0 (VVRM 10.0 (V
VRM 10.0 (VVRM 10.0 (V
VRM 10.0 (Voltage Roltage R
oltage Roltage R
oltage Regulator Modules) on Boardegulator Modules) on Board
egulator Modules) on Boardegulator Modules) on Board
egulator Modules) on Board
• Flexible motherboard design with on board VRM 10.0, easy to upgrade
with future Intel® Celeron, Northwood and Prescott processors.
• 0.8375V to 1.600V in 12.5mV steps.
CacheCache
CacheCache
Cache
• The Intel® Celeron, Northwood and Prescott processors built-in L2
Cache.
System MemorySystem Memory
System MemorySystem Memory
System Memory
•Dual-channel (128 bits wide) DDR memory interface.
•Single-channel (64 bits wide) DDR operation supported.
•Supports 128Mb,256Mb,512Mb technologies implemented as X8,X16
devices.
•Supports four bank devices.
•Supports Non-ECC,Un-buffered DIMMs only.
•Maximum memory size:4GB.
•Supports suspend to RAM (optional).
•DIMMs must be populated in identical pairs for Dual channel
operation.
•Supports DDR266/DDR333/DDR400 unregistered non-ECC DDR
DIMMs.
Note: Please ensure that your DIMMs can meet the specification of SPD.
AGP ControllerAGP Controller
AGP ControllerAGP Controller
AGP Controller
• Supports AGP3.0 with 4X or 8X AGP data transfers and 4X/8X Fast
Writes respectively.
• AGP 1.5V connector support only, No support for 3.3V or Universal AGP
connectors.
• High priority access support.
• Delayed transaction support for AGP reads that cannot be serviced
immediately.

5
Hardware Configuration
On-board I/OOn-board I/O
On-board I/OOn-board I/O
On-board I/O
• On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 , Ultra
ATA33/66/100 IDE HDDs, CD-ROMs, ZIP drives and LS-120 drives as
boot drive.
• One ECP/EPP parallel port.
• Two 16550 Compatible UART serial ports.
• One floppy port supports two FDD of 360KB, 720KB, 1.2MB , 1.44MB
and 2.88MB capacity.
• PS/2 keyboard connector.
• PS/2 mouse is supported.
• One front panel sound connector.
• Infrared (IrDA) is supported via a header.
• Two on board SATA ports.
Expanded USB SupportExpanded USB Support
Expanded USB SupportExpanded USB Support
Expanded USB Support
• Includes 4 UHCI host controllers,increasing the number of external
ports to eight.
• Includes 1 EHCI USB2.0 Host Controller that supports all eight
ports(Bandwidth shared between eight ports).
On-board VGA (only for 865G)On-board VGA (only for 865G)
On-board VGA (only for 865G)On-board VGA (only for 865G)
On-board VGA (only for 865G)
• Core Frequency of 266MHz.
• 3D Setup Render Engine.
• High Quality Texture Engine.
• 3D Graphics Rasterization Enhancements.
• Full 2D H/W Acceleration.
• Motion Video Acceleration.
• Up to 1600x1200 in 8 bit Color at 85Hz Refresh.
• H/W Motion Compensation Assistance for S/W MPEG2 Decode.
• Software DVD at 30fps.
• Integrated 24-bit 230MHz RAMDAC.
Integrated Serial AIntegrated Serial A
Integrated Serial AIntegrated Serial A
Integrated Serial ATT
TT
TA host ControllerA host Controller
A host ControllerA host Controller
A host Controller
•Independent DMA operation on two ports.
• Data transfer rates of 150Mb/s.
• RAID feature support (optional).
On-board Realtek RTL8100BL PCI LAN (optional)On-board Realtek RTL8100BL PCI LAN (optional)
On-board Realtek RTL8100BL PCI LAN (optional)On-board Realtek RTL8100BL PCI LAN (optional)
On-board Realtek RTL8100BL PCI LAN (optional)
•The RTL8100BL is a single-chip 10/100MB/s controller for the PCI bus.
•Integrated PCI Ethernet media access controller RT8100.
•Supports Wake-On-LAN function.
•Supports LEDs for various network activity indications.

6
Technical Reference Booklet
System BIOSSystem BIOS
System BIOSSystem BIOS
System BIOS
•PnP,APM, ATAPI and Windows®98/2000/XP.
• Full support of ACPI & DMI.
•Auto detects and supports LBA harddisks with capacities over 8.4GB.
•Easy to upgrade BIOS by end-user.
Plug and PlayPlug and Play
Plug and PlayPlug and Play
Plug and Play
•Supports Plug and Play specification 1.1.
•Plug and play for Windows® 98/2000, as well as Windows® XP.
•Fully steerable PCI interrupts.
Power ManagementPower Management
Power ManagementPower Management
Power Management
• SupportsSMM, APMand ACPI.
• Break switch for instant suspend/resume on system operations.
• Energy star “Green PC” compliant.
• Hardware monitoring circuit is supported, provide voltage, fan speed,
etc. monitoring (optional).
• WOL (Wake-On-Lan) Header support.
• External Modem Ring-in Wake-up support.
• Supports suspend-to-RAM(STR)(optional).
On-board AC97 SoundOn-board AC97 Sound
On-board AC97 SoundOn-board AC97 Sound
On-board AC97 Sound (optional)(optional)
(optional)(optional)
(optional)
•Integrated AC97 controller with standard AC97 Codec.
• Direct Sound and Sound Blaster compatible.
•Full-Duplex 16-bit record and play back.
•PnP and APM 1.2 support.
•Windows® 98/2000/XP drivers ready.
•Line-in, Line-out, Mic-in and MIDI/Game port.
• Supports ALC650 AC97 Code for six sound channel output (optional).
On-board IEEE1394On-board IEEE1394
On-board IEEE1394On-board IEEE1394
On-board IEEE1394(optional)(optional)
(optional)(optional)
(optional)
•Compliant with 1394 open HCI specifications v1.0 and v1.1.
• Integrated 400Mbit 2 port PHY.
Expansion SlotsExpansion Slots
Expansion SlotsExpansion Slots
Expansion Slots
• 1 AGP slot.
•6 PCI bus master slots - ver. 2.1 compliant.
Static electricity can harm delicate components of the motherboard.
To prevent damage caused by static electricity, discharge the static
electricity from your body before you touch any of the computers
electronic components.

7
Motherboard Layout (35-Motherboard Layout (35-
Motherboard Layout (35-Motherboard Layout (35-
Motherboard Layout (35-AA09-AA09-
AA09-AA09-
AA09-X0-X0-
X0-X0-
X0-XX)XX)
XX)XX)
XX)
The following diagrams show the relative positions of the jumpers,
connectors, major components and memory banks on the motherboard.
# Both the LAN and the Video out connectors are optional.
# The ALC650 embeds an internal analog switch (by driver software) to share
LINE input with Surround output, and share MIC input with CENTER/LFE
output.
NOTE
1) Be sure to check the cable orientation in order to match the colored strip to
the pin1 end of the connector.
2) When you start up the system, please wait for 5 seconds after you power
on AC.
3) It is not recommended to add a metal spacer plate on the back of the
Socket478. Otherwise, some components will be short and damaged.
Motherboard Layout

8
Technical Reference Booklet
PIN SIGNAL DESCRIPTION
1 VCC +5V/5VSB (optional)
2 -Data 0 Negative Data Channel 0
3 +Data0 Positive Data Channel 0
4 GND Ground
5 VCC +5V/5VSB (optional)
6 -Data 1 Negative Data Channel 1
7 +Data 1 Positive Data Channel 1
8 GND Ground
Rear PanelRear Panel
Rear PanelRear Panel
Rear Panel
The back panel provides the following connectors:
Mouse ConnectorMouse Connector
Mouse ConnectorMouse Connector
Mouse Connector
The mainboard provides a standard PS/2® mouse mini DIN connector for
attaching a PS/2® mouse.You can plug a PS/2® mouse directly into this
connector.
Keyboard ConnectorKeyboard Connector
Keyboard ConnectorKeyboard Connector
Keyboard Connector
The mainboard provides a standard PS/2® keyboard mini DIN connector
for attaching a PS/2® keyboard.You can plug a PS/2® keyboard directly into
this connector.
USB 2.0 ConnectorUSB 2.0 Connector
USB 2.0 ConnectorUSB 2.0 Connector
USB 2.0 Connector
The mainboard provides a UHCI (Universal Host Controller Interface)
Universal Serial Bus root for attaching USB devices such as keyboard, mouse
or other USB-compatible devices.You can plug the USB device directly into
the connector.
USB 2.0 Connector DescriptionUSB 2.0 Connector

9
Serial Port Connector: COM1Serial Port Connector: COM1
Serial Port Connector: COM1Serial Port Connector: COM1
Serial Port Connector: COM1
The Port is 16550A high speed communication ports that send/receive 16
bytes FIFOs. You can attach a serial mouse or other serial devices directly
to the connectors.
Video Out Connector (Optional)Video Out Connector (Optional)
Video Out Connector (Optional)Video Out Connector (Optional)
Video Out Connector (Optional)
The mainboard provides a Video out port to connect a 15-pin analog
videomonitor.
RJ-45 LAN Jack (Optional)RJ-45 LAN Jack (Optional)
RJ-45 LAN Jack (Optional)RJ-45 LAN Jack (Optional)
RJ-45 LAN Jack (Optional)
The mainboard provides one standard RJ-45 jack for connection to Local
Area Network(LAN).You can connect a network cable to the LAN jack.
Parallel Port Connector:LPT1Parallel Port Connector:LPT1
Parallel Port Connector:LPT1Parallel Port Connector:LPT1
Parallel Port Connector:LPT1
The mainboard provides a 25-pin female centronic connector as LPT. A
parallel port is a standard printer port that supports Enhanced Parallel Port
(EPP) and Extended Capabilities Parallel Port (ECP) mode.
MIDI/Game ConnectorMIDI/Game Connector
MIDI/Game ConnectorMIDI/Game Connector
MIDI/Game Connector
The mainboard provides the game port to connect a joystick or a MIDI
device.
Audio Port ConnectorAudio Port Connector
Audio Port ConnectorAudio Port Connector
Audio Port Connector
SPK_Out is a connector for Speakers or Headphones. Line In is used for
external CD player, Tape player, or other audio devices. Mic In is a connector
for microphones. The ALC650 embeds an internal analog switch (by driver
software) to share LINE input with Surround output, and share MIC input with
CENTER/LFE output.
RearPanel

10
Technical Reference Booklet
ConnectorsConnectors
ConnectorsConnectors
Connectors
The mainboard provides connectors to connect to FDD, IDE HDD, USB
Ports and CPU/System FAN.
Floppy Disk Drive Connector:CN3
The mainboard provides a standard floppy disk drive connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types.
Hard Disk Connectors:CN1&CN2
The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/66/100
controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 33/66/100
function. You can connect up to four hard disk drives, CD-ROM, 120MB
Floppy (reserved for future BIOS) and other devices.
CN1 (Primary IDE Connector)
The first hard drive should always be connected to CN1.CN1 can connect
a Master and a Slave drive.You must configure second hard drive to Slave
mode by setting the jumper accordingly.
CN2 (Secondary IDE Connector)
CN2 can also connect a Master and a Slave drive.
CN3
CN1 CN2

11
Serial ATA Hard Disk Connectors: SATA-1/SATA-2
The mainboard has 2 SATA connectors. The mainboard provides optional
dual high-speed Serial ATA interface ports, SATA-1 & SATA-2. Each supports
1st generation serial ATA data rates of 150 MB/s. Both connectors are fully
compliant with Serial ATA 1.0 specifications. Each Serial ATA connector can
connect to 1 hard disk device. Please refer to Serial ATA Raid manual for detail
software installation procedure.
SATA-1
SATA-2
Connectors
PIN SIGNAL
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SASA
SASA
SATT
TT
TAA
AA
A-1&SA-1&SA
-1&SA-1&SA
-1&SATT
TT
TAA
AA
A-2-2
-2-2
-2
NOTENOTE
NOTENOTE
NOTE
1) If SATA ports were used, For PATA controller, either the primary or secondary
can be used, but not both.
2) PATA devices only: Max. support 4 devices.
3) SATA devices only: Max. support 2 devices.
4) PATA+SATA: Max. support 4 devices(2 PATA + 2 SATA).
5) Some OS(e.g. Windows XP and future OS) can support Max. 6 devices
(2 SATA + 4 PATA).

12
Technical Reference Booklet
Serial ASerial A
Serial ASerial A
Serial ATT
TT
TA CableA Cable
A CableA Cable
A Cable
Connect to SATA-1 or SATA-2
Connect to the hard disk devices
Please do not fold the serial ATA cable in a 90-degree angle, which
will cause the loss of data during the transmission.
Serial ASerial A
Serial ASerial A
Serial ATT
TT
TA Hard Disk Devices PA Hard Disk Devices P
A Hard Disk Devices PA Hard Disk Devices P
A Hard Disk Devices Power Cableower Cable
ower Cableower Cable
ower Cable

13
S-Bracket(SPDIF)/CEN/LFE/Surround Output/CEN/LFE/Surround Output
/CEN/LFE/Surround Output/CEN/LFE/Surround Output
/CEN/LFE/Surround Output Connector:
CN55 (green) (optional)
The connector allows you to connect a S-Bracket for a Digital Interface
(SPDIF). The S-Bracket offers 1 SPDIF jacks for digital audio transmission
and 2 analog Line-Out jacks for other 4-channel audio output. So you can use
Line in, Mic in and 6 channel audio output features at the same time.
CN55
Connectors
22
22
2
11
11
1
1010
1010
10
99
99
9

14
Technical Reference Booklet
PIN SIGNAL DESCRIPTION
1 SOUT-L Audio left surrounding output
2 SOUT-R Audio right surrounding output
3 GND Ground
4 GND Ground
5 CET-OUT Audio center output
6 LFE-OUT Audio bass output
7 GND Ground
8 SPDIF S/PDIFinput
9 (NoPin) Key
10 SPDFO S/PDIFoutput
CN55-CN55-
CN55-CN55-
CN55-SS
SS
S-Brack-Brack
-Brack-Brack
-Bracketet
etet
et
S-Bracket Cable (optional)S-Bracket Cable (optional)
S-Bracket Cable (optional)S-Bracket Cable (optional)
S-Bracket Cable (optional)
Connect to CN55
SPDIF jack (coaxial)
Analog Line-Out jack

15
IEEE 1394 Connectors: CN53,CN54 (optional)
The mainboard provides two 1394 pin headers that allow you to connect
optional IEEE 1394 ports (yellow).
11
11
1
22
22
2
99
99
9
1010
1010
10
11
11
1
22
22
2
99
99
9
1010
1010
10
CN54CN54
CN54CN54
CN54 CN53CN53
CN53CN53
CN53
Connectors

16
Technical Reference Booklet
PIN SIGNAL
1TPA+
2TPA-
3 Ground
4 Ground
5 TPB+
6 TPB-
7 Cable power
8 Cable power
9 Key (no pin)
10 Ground
CN53,CN54 Pin DefinitionCN53,CN54 Pin Definition
CN53,CN54 Pin DefinitionCN53,CN54 Pin Definition
CN53,CN54 Pin Definition
IEEE 1394 Cable (optional)IEEE 1394 Cable (optional)
IEEE 1394 Cable (optional)IEEE 1394 Cable (optional)
IEEE 1394 Cable (optional)

17
Fan Power Connectors:CPUFAN/SYSFAN
The CPUFAN (processor fan), SYSFAN (system fan) support system cool
-ing fan with +12V.It supports three-pin head connector. When connecting the
wire to the connectors, always take note that the red wire is the positive and
should be connected to the +12V, the black wire is Ground and should be
connected to GND. If the mainboard has a System Hardware Monitor chipset
on-board, you must use a specially designed fan with speed sensor to take
advantage of the CPU fan control.
SYSFAN
CPUFAN
1
1
1
WOL
WOL: Wake On LAN
If you have installed a LAN card, use the cable provied with the card to plug
into the mainboard WOL connector. This enables ables the Wake On LAN
(WOL) feature. When your system is in a power-saving mode, any LAN signal
automatically resumes the system.You must enable this item using the Power
Mannagement page of the Setup Utility.
Connectors

18
Technical Reference Booklet
CD-IN Connector:CDS1
The connector is for CD-ROM Drive.
AUX-IN Connector:AUX1
The connector is for Audio Device.
CDS1 AUX1
1 1
PIN Assignment
1 CD-L
2 GND
3 GND
4 CD-R
CDS1 : CD-INCDS1 : CD-IN
CDS1 : CD-INCDS1 : CD-IN
CDS1 : CD-IN
AA
AA
AUX1 : AUX1 : A
UX1 : AUX1 : A
UX1 : AUXUX
UXUX
UX-IN-IN
-IN-IN
-IN
PIN Assignment
1 AUX-L
2 GND
3 GND
4 AUX-R

19
PIN Assignment
1 MIC
2 GND
3 REF
4 POWER
5 Front Audio(R)
6 Rear Audio(R)
7 Reserved
8 Key(No pin)
9 Front Audio(L)
10 Rear Audio(L)
Front Panel Audio Header: FP_SFront Panel Audio Header: FP_S
Front Panel Audio Header: FP_SFront Panel Audio Header: FP_S
Front Panel Audio Header: FP_S
This mainboard supports front panel microphone and speaker out ports.
If your computer case has these ports,connect them to FP_S.
FP_SFP_S
FP_SFP_S
FP_S
10 9
2
4
6
8
1
3
5
7
FP_SFP_S
FP_SFP_S
FP_S
Note:
If you want to use “Front Audio” connector, you must move 5,6,9,10 jumper.
In order to utilize the front audio header, your chassis must have front
audio connector. Also please make sure the pin assignment on the cable
is the same as the pin assignment on the MB header. To find out if the
chassis you are buying support front audio connector, please contract
your dealer.
Connectors

20
Technical Reference Booklet
USB Connectors: FP_U1/FP_U2/FP_U3USB Connectors: FP_U1/FP_U2/FP_U3
USB Connectors: FP_U1/FP_U2/FP_U3USB Connectors: FP_U1/FP_U2/FP_U3
USB Connectors: FP_U1/FP_U2/FP_U3
This mainboard has USB ports. Some computer cases have a special
module that mounts USB ports at the front of the case. If you have this kind
of case, use auxiliary USB connector FP_U1/FP_U2/FP_U3 to connect the
front mounted ports to the mainboard.
11
11
1
22
22
2
99
99
9
1010
1010
10
11
11
1
22
22
2
99
99
9
1010
1010
10 11
11
1
22
22
2
99
99
9
1010
1010
10
FP_U3FP_U3
FP_U3FP_U3
FP_U3 FP_U2FP_U2
FP_U2FP_U2
FP_U2 FP_U1FP_U1
FP_U1FP_U1
FP_U1
PIN Assignment
1 VCC
2 VCC
3 USBP0-
4 USBP1-
5 USBP0+
6 USBP1+
7 GND
8 GND
9 KEY
10 OC#
USB ConnectorUSB Connector
USB ConnectorUSB Connector
USB Connector