peerless-AV SS560G Guide

Installation and Assembly: Display Stand for 32" - 65"
Flat Panel Displays
Models: SS560G
ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity:
150 lb (68 kg) display
50 lb (22.7 kg) per shelf

2 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Cart .....................................................................................................................................................................5
Attaching Universal Adapter Plate or Dedicated Adapter Plate........................................................................................... 10
Installing Adapter Brackets ..................................................................................................................................................11
Cord Management............................................................................................................................................................... 13
Tools Needed for Assembly
• level
• phillips screwdriver
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum UL Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The stand is not affixed or secured to the floor, and may therefore tip over and/or fall if display and/or stand is
shaken or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a
falling display. Not recommended for use in areas with heavy traffic.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING

3 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
Description Qty. Part Numbe
r
A
screen mount bracket 1 201-1156
Bhook plate 1 201-1157
Cshelf support 1 201-1158
Dshelf clamp bracket 1 201-1159
Ebase 1 009-1223
Funiversal plate 1 201-1110
Gadapter bracket 2 201-1510
Hupright 1 580-1180
Iglass shelf 1 590-1208
Jtop cover 1 590-1210
Kbutton bumper 9 590-1209
L1/4-20 x 12 mm decorative screw 14 520-2325
M1/4-20 nut 12 530-1022
O3/8-16 x 2.5" socket screw 3 520-9550
P7/32" allen wrench 1 560-9715
Q4 mm allen wrench 1 560-9646
R6 mm allen wrench 1 560-9716
Sleft leg 1 009-1287
Tright leg 1 009-1288
U
ft
4
600 1025
Parts List
Ufoot 4 600-1025
Wjoint connector nut 4 530-1037
X
3/8-16 x 1.5" bolt 4 520-1329
Y
M10 x .402 ID washer 3 540-9424
A
A
1/4-20 x 20 mm screw 2 520-2326
BB 3/16" allen wrench 1 560-0071
CC M4 x 12 mm serrated washer head socket pin screw 6 510-1079
DD M4 x 25 mm serrated washer head socket pin screw 4 510-1082
EE M5 x 12 mm socket pin screw 4 520-1064
FF M5 x 25 mm socket pin screw 4 520-1122
GG M6 x 12 mm socket pin screw 4 520-1050
HH M6 x 25 mm socket pin screw 4 520-1211
II M8 x 15 mm socket pin screw 6 520-1068
JJ M8 x 40 mm socket pin screw 4 520-1152
KK 1/2" x 1/2" spacer 4 540-1057
LL 3/4" x 1/2"spacer 4 540-1059
MM multi washer 6 580-1036
NN M6 x 20 mm socket pin screw 4 520-9554
OO M6 x 30 mm socket pin screw 4 520-1067
PP M8 x 25 mm socket pin screw 4 520-1101
QQ M10 x 15 mm socket screw 4 520-9262

4 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
R
Q
BB
H
E
ABC
W
J
Y
P
X
O
QQ
L M
Parts List continued D
K
I
AA
S
T
OO
II
Some parts may appear slightly different than illustrated.
CC DD EE JJFF HH
GG
MM
LL
KK NN PP G
F
U

5 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Insert right leg (T) into base housing (E) as shown in fig.1.1. Then line up holes of right leg with holes in bas
housing (E). Fasten base housing to right leg using two 3/8-16 x 1.5" bolts (X)and two joint connectors (W), tighten
using 3/16"allen wrench (BB) and 7/32"allen wrench (P) as shown in fig.1.2.
NOTE: Left and right legs can be identified by looking at the cart from the front.
Repeat for left side with left leg (S).
1
T
X
fig. 1.2
W
fig. 1.1
E
T
FRONT OF CART
FRONT OF LEG
Insert feet (U) into holes of support legs (S&T) and hand thread to secure.
S
U
T
2

6 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Attach upright (H) to base (E), as shown in fig 3.1 using three 3/8-16 x 2.5" socket screws (O) and M10 x .402ID
lock washers (Y). Tighten screws using 7/32" allen wrench (P).
NOTE: Be sure cord management holes are in the configuration shown in fig 3.2.
3
Loosely attach four 1/4-20 x 12 mm screws (L) and 1/4-20 nuts (M) to shelf support (C).
4
C
LM
fig. 3.2
CORD
MANAGEMENT
HOLES
O
E
H
Y
fig. 3.1

7 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
SLOT
fig 5.1
C
Slide shelf support (C)onto upright (H) so that 1/4-20 nuts (M) slide into slots of upright (H) as shown in
figure 5.1 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L)
using 4 mm allen wrench (Q).
NOTE: MAXIMUM OF TWO SHELVES
Max height of top shelf is 34" from base.
Max height of second shelf is 28" from base.
DETAIL 1
5
M
H

8 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Insert three button bumpers (K) into bottom of shelf clamp bracket (D).
Attach shelf clamp bracket (D) to shelf support (C) using two 1/4-20 x 20 mm screws (AA) and two
1/4-20 nuts (M).
For additional shelf installation, repeat steps 4 through 6.
Insert six button bumpers (K) into shelf support (C). Place glass shelf (I) on shelf support.
I
K
C
6
6-1
K
6A
6-2
Attaching Glass Shelf
D
C
AA
M
• Do not overtighten, may cause glass to shatter or
crack.
• This shelf is intended for use with equipment
weighing NO more than 50 lbs. (22.7 kg) that fits
evenly accross the surface of glass shelf (I). Use
with other equipment may result in instability and
cause personal injury or property damage.
WARNING

9 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Insert two 1/4-20 x 12 mm screws (L) into display
mount bracket (A), leaving 3/16" of exposed thread
as shown in figure 10.1 and detail 3.
J
H
Snap top cover (J) onto upright (H). 109
fig. 10.1
DETAIL 3
L
A
Loosely attach six 1/4-20 x 12 mm screws (L) and
1/4-20 nuts (M) to display mount bracket (A).
7Slide display mount bracket (A) onto upright (H) so
that 1/4-20 nuts (M) slide into slots of upright (H) as
shown in figure 8.1 and detail 2. Slide display mount
bracket to desired position, level, then tighten 1/4-
20 x 12 mm screws (L) using 4 mm allen wrench
(Q).
8
LA
MA
H
SLOT
fig. 8.1
L
DETAIL 2
M
H
3/16"

10 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Attach Universal Plate (F) or Dedicated Adapter
Plate to hook plate (B) using four M10 x 15 mm
socket screws (QQ). Tighten screws using 6 mm
allen wrench (R).
Attaching Universal Adapter Plate or Dedicated Adapter Plate
Attach hook plate (B) to display mount bracket (A).
L
LL
2° Backward Tilt 5° Forward TiltNo Tilt
Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired display orientation. Tighten all screws
using 4 mm allen wrench (Q).
11 12
13
F
B
QQ
B
A

11 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
NOTE: "X" dimensions should be equal.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
Installing Adapter Brackets
GCENTER BRACKETS
VERTICALLY ON
BACK OF DISPLAY
X
X
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not be
used, depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MULTI-WASHER
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down. Refer to display manufacturers instructions or customer service, for removing any
knobs, base, cover, or screw(s) on the back of the display to prepare mounting. These need to be removed to
allow the adapter brackets (G) to be attached. Select the small, medium, large or extra large screws from the
baffled fastener pack then attach adapter brackets to display following figure 14.1 or 14.2.
NOTE: Top and bottom mounting holes must be used for attaching brackets. Verify that all holes are properly
aligned, and then tighten screws using 4 mm security allen wrench (Q).
NOTE: For flat back displays proceed to step 14-1. For bump-out or recessed back display skip to step 14-2.
14

12 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as
shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the
baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
14-1
14-2
DISPLAY
MULTI-WASHER
SCREW
ADAPTER
BRACKET (G)
fig. 14.2
SPACER
ADAPTER
BRACKET (G)
DISPLAY
fig. 14.1
MULTI-WASHER
SCREW
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.

13 of 41 ISSUED: 02-25-11 SHEET #: 009-9051-2 09-14-11
Mounting and Removing Flat Panel Display
Hook adapter brackets (G) onto universal plate (F),
then slowly swing display in as shown. Turn screws
of adapter brackets (G) clockwise at least six times
to prevent display from being removed as shown in
detail 4.
NOTE: Tighten using 4 mm allen wrench (R).
Display can be adjusted horizontally if desired.
NOTE: It is important to lock display down!
To lock the display down, fully tighten screws to
adapter bracket as shown in detail 4.
To remove display from mount, loosen screws,
swing display away from mount, and lift display off
of mount.
15
G
DETAIL 4
SCREWS
F
G
F
Run cords through upright (H) using cord management holes.
16
CORD
MANAGEMENT
H
Cord Management
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com

Instalación y Ensamblaje: 32" - 65" Pantalla de Panel
Plano Estante
Models: SS560G
PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Máxima capacidad de carga de UL:
150 lb (68 kg) pantalla
50 lb (22.7 kg) por repisa

Español
15 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
NOTA: Lea toda la hoja de instrucciones antes de iniciar la instalación y el montaje.
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las
advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente
internacional, por favor, comuníquese con su distribuidor local.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga
experiencia en construcción básica de edifi cios y que entienda estas instrucciones en su totalidad.
• Nunca sobrepase la capacidad máxima de soportar carga. Vea la página 14.
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
con más seguridad.
• Apriete los tornillos con fi rmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede
disminuir signifi cativamente su fuerza de fi jación.
• El estante no está anclado ni fijado al suelo y, por lo tanto, podría volcarse o caerse si la pantalla o el estante reciben
una sacudida o un golpe. Vigile siempre a los niños y no los deje jugar solos cerca del estante, ya que podrían
lastimarse si se cae la pantalla. No se recomienda para uso en áreas de mucho tránsito.
• Este producto está diseñado para uso en interiores solamente. Utilizar este producto en exteriores podría causar
fallas del producto y lesiones a individuos.
ADVERTENCIA
Tabla de contenido
Lista de Piezas ............................................................................................................................................................... 16,17
Armar el Estante.................................................................................................................................................................. 18
Fijar la Placa Adaptadora Universal o la Placa Adaptadora Exclusiva................................................................................ 23
Instalación de los Soportes Adaptadores ............................................................................................................................ 24
Manejo de Cables................................................................................................................................................................ 26
Herramientas necesarias para el ensamblaje
• nivel
• destornillador phillips

Español
16 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
Antes de comenzar, coteje la lista de piezas para asegurarse de que se han incluido todas las piezas.
Las piezas pueden verse un poco distintas a la ilustración.
Descripción Cant. Pieza N°
A
soporte de montaje para pantallas 1 201-1156
Bplaca de enganche 1 201-1157
Csoporte de apoyo de la repisa 1 201-1158
Dabrazadera para repisas 1 201-1159
Ebase 1 009-1223
Fplaca universal 1201-1110
Gsoporte adaptador 2 201-1510
Hcolumna vertical 1 580-1180
Irepisa de cristal 1 590-1208
Jcubierta superior 1 590-1210
Kparagolpe de botón 9 590-1209
Ltornillo decorativo de 1/4-20 x 12 mm 14 520-2325
Mtuerca de 1/4-20 12 530-1022
Otornillos de cabeza hueca 3/8-16 x 2.5" 3 520-9550
Pllave allen de 7/32" 1 560-9715
Qllave allen de 4 mm 1 560-9646
Rllave allen de 6 mm 1 560-9716
Spata izquierda 1 009-1287
Tpata derecha 1 009-1288
Lista de Piezas
p
Upie 4 600-1025
Wtuerca conectora de juntas 4 530-1037
X
pernos de 3/8-16 x 1.5" 4 520-1329
Y
arandelas de cierre de M10 x .402ID 3 540-9424
A
A
tornillos de 1/4-20 x 20 mm 2 520-2326
BB llave allen de 3/16" 1 560-0071
CC seguridad tornillos de cabeza hueca M4 x 12 mm 6 510-1079
DD seguridad tornillos de cabeza hueca M4 x 25 mm 4 510-1082
EE seguridad tornillos de cabeza hueca M5 x 12 mm 4 520-1064
FF seguridad tornillos de cabeza hueca M5 x 25 mm 4 520-1122
GG seguridad tornillos de cabeza hueca M6 x 12 mm 4 520-1050
HH seguridad tornillos de cabeza hueca M6 x 25 mm 4 520-1211
II seguridad tornillos de cabeza hueca M8 x 15 mm 6 520-1068
JJ seguridad tornillos de cabeza hueca M8 x 40 mm 4 520-1152
KK 1/2" x 1/2" espaciador 4 540-1057
LL 3/4" x 1/2" espaciador 4 540-1059
MM arandela múltiple 6 580-1036
NN seguridad tornillos de cabeza hueca M6 x 20 mm 4 520-9554
OO seguridad tornillos de cabeza hueca M6 x 30 mm 4 520-1067
PP seguridad tornillos de cabeza hueca M8 x 25 mm 4 520-1101
QQ tornillos de cabeza hueca M10 x 15 mm 4 520-9262

Español
17 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
R
Q
BB
H
E
ABC
W
J
Y
P
X
O
QQ
L M
lista de piezas continúa D
K
I
AA
S
T
OO
II
Las piezas pueden verse un poco distintas a la ilustración.
CC DD EE JJFF HH
GG
MM
LL
KK NN PP G
F
U

Español
18 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
Inserte la pata derecha (T) en la cubierta de la base (E), como se muestra en la figura 1.1. Luego, alinee los
agujeros de la pata derecha con los agujeros de la cubierta de la base (E). Fije la cubierta de la base en la pata
derecha con dos pernos de 3/8-16 x 1.5" (X) y dos conectores de juntas (W), apriételos utilizando una llave allen
de 3/16" (BB) y una llave allen de 7/32" (P), como se muestra en la figura 1.2.
NOTA: La pata izquierda y la pata derecha se pueden identificar mirando el frente del estante.
Haga lo mismo con el lado izquierdo y la pata izquierda (S).
1
T
X
fig. 1.2
W
fig. 1.1
E
T
FRENTE DEL
ESTANTE
FRENTE DE LA PATA
Inserte los pies (U) en los agujeros de la patas de apoyo (S y T) y enrósquelos con la mano para fijarlos.
S
U
T
2

Español
19 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
Fije la columna vertical (H) en la base (E), como se muestra en la figura 3.1, con tres tornillos de cabeza hueca
de 3/8-16 x 2.5" (O) y tres arandelas de cierre de M10 x .402ID (Y). Apriete los tornillos usando una llave allen de
7/32" (P).
NOTA: Asegúrese de que los agujeros para el manejo de los cables estén en la configuración que se muestra en
la figura 3.2.
3
Coloque cuatro tornillos de 1/4-20 x 12 mm (L) y cuatro tuercas de 1/4-20 (M) en el soporte de apoyo de la repisa
(C), pero no los fije.
4
C
LM
fig. 3.2
AGUJEROS PARA
EL MANEJO DE
CABLES
O
E
H
Y
fig. 3.1

Español
20 de 41 PUBLICADO: 02-25-11 HOJA #: 009-9051-2 09-14-11
RANURA
fig 5.1
C
Deslice el soporte de apoyo de la repisa (C) en la columna vertical (H), de manera que las tuercas de 1/4-20 (M)
se deslicen en las ranuras de la columna vertical (H), como se muestra en la figura 5.1 y en el detalle 1. Deslice el
soporte de apoyo de la repisa hasta la posición deseada, nivélelo y apriete los tornillos de
1/4-20 x 12 mm (L) utilizando una llave allen de 4 mm (Q).
NOTA: MÁXIMO DE DOS REPISAS
La altura máxima de la repisa superior es de 34"
de la base.
La altura máxima de la segunda repisa es de 28"
de la base.
DETALLE 1
5
M
H