peerless-AV PLA 60-UNL-S Guide

Models: PLA 60-UNL, PLA 60-UNL-S,
PLA 60-UNLP, PLA 60-UNLP-S,
PLAV 60-UNL, PLAV 60-UNL-S,
PLAV 60-UNLP, PLAV 60-UNLP-S
RTPLA 60, RTPLA 60-S, RTPLA UN7,
RTPLA UN7S, D-FPA-320, D-FPA-320S
Installation and Assembly - Universal Articulating
SwivelArm for 37" - 60" Plasma Screens
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Maximum UL Load Capacity:175 lb (79 kg)

2 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Tools Needed for Assembly
•studfinder ("edge to edge"stud finder is recommended)
•drill
•7/32" drill bit for wood studs
•5/16" masonry drill bit for concrete
•7/16"socket wrench with extension (recommended)
•level
•phillipsscrewdriver
Accessories
•External Wall Plate (WSP716, WSP716-S, WSP724,
WSP724-S)(MetalStudnotevaluatedby UL)
• Donot begin to install yourPeerlessproduct until you have readandunderstood the instructions and warnings
containedin this Installation Sheet. If youhave any questions regarding any oftheinstructions or warnings, please
callPeerlesscustomercareat1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supportingsurface will safely support thecombined load of the equipmentand all attached hard-
wareandcomponents.
• Neverexceedthe Maximum ULLoadCapacity. See pageone.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgetoedge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsfirmly, but do not overtighten. Overtightening can damage the items, greatly reducingtheirholding
power.
• Thisproductwas designed and intended to be mounted to thefollowingsupportingsurfaceschecked below with the
hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-
ingsurface,contactPeerlesscustomercareat1-800-865-2112.
• This product was designed to be installed on the following wall construction only;
WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED
xWoodStud None
xWoodBeam None
xSolidConcrete None
xCinderBlock None
MetalStud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick ContactCustomerService
Otherorunsure? ContactCustomerService
WARNING
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Double Wood Stud Wall..................................................................................................................................6
Installation to Solid Concrete or Cinder Block .......................................................................................................................7

3 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
E
F
D
Wall Mount Parts List
K
MS
T
C
A
H
B
N
R
L
Q
Some parts may appear slightly different than illustrated.
I
Before you start make sure all parts
listed are included with your product.
OUV
RTPLA 60 RTPLA 60-S
G
RTPLA UN7 RTPLA UN7S
D-FPA-320 D-FPA-320S
JW
P
PLA60-UNL PLA60-UNL-S PLAV60-UNL PLAV60-UNL-S
PLA60-UNLP PLA60-UNLP-S PLAV60-UNLP PLAV60-UNLP-S
DESCRIPTION QTY. PART# PART# PART# PART#
Awallplate 1 201-1040 201-4040 201-1040 201-4040
Btilt-roll assembly 1 201-1093 201-4093 201-1048 201-4048
Carmassembly 1 201-1072 201-4072 201-1049 201-4049
Dwallsupportarmaxle 1 201-1041 201-1041 201-1041 201-1041
Evinyltrim 3 600-1012 600-1012 600-1012 600-1012
FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262 520-9262 520-9262
G.505 x .75 x .062" nylon washer 1 540-1074 540-1074 540-1074 540-1074
Htilt adjustment knob 1 560-0108 560-0108 560-0108 560-0108
Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315 520-1315 520-1315
J1.525 x 2 x .062" delrin washer 2 540-1070 540-1070 540-1070 540-1070
K#8-32 x .375" socket cap screw 1 520-1210 520-1210 520-1210 520-1210
Lplastic finishing cap 8 590-1123 590-1123 590-1123 590-1123
Mholdingpin 1 580-1166 580-1166 580-1166 580-1166
Nretainerplug 1 590-1007 590-1007 590-1007 590-1007
O5/16 x 3" wood screw 8 520-1243 520-1243 520-1243 520-1243
P.250 x 1 x .068" washer 8 540-1063 540-1063 540-1063 540-1063
Q9/64"allenwrench 1 560-9728 560-9728 560-9728 560-9728
Rcablemanagementclips 4 590-1166 590-1166 590-1166 590-1166
Scable tie 4 590-1168 590-1168 590-1168 590-1168
T36"polyestermeshsleeve 1 600-1015 600-1015 600-1015 600-1015
U6mmallenwrench 1 560-9716 560-9716 560-9716 560-9716
V10mmallenwrench 1 n/a n/a 560-9727 560-9727
Wanchor 8 590-1025 590-1025 590-1025 590-1025

4 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
DD
CCBBAA
Before you begin, make sure all parts shown are included with your product. D-FPA-320 D-FPA-320S
RTPLA UN7 RTPLA UN7S
RTPLA 60 RTPLA 60-S
PLA 60-UNL PLA 60-UNL-S PLA 60-UNLP PLA 60-UNLP-S
PLAV 60-UNL PLAV 60-UNL-S PLAV 60-UNLP PLAV 60-UNLP-S
Description Qty Part # Part # Part # Part #
AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110
BB shallow adapter bracket 2 201-1511 201-4511 201-1514 201-4514
CC deep adapter bracket 2 201-1510 201-4510 201-1513 201-4513
DD allen wrench 1 560-9646 560-9646 560-0072 560-0072
Adapter Bracket Parts List

5 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211 multi-washer(6)
580-1036
SecurityAdapter Bracket Fasteners
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 multi-washer(6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Phillips Adapter Bracket Fasteners
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208 M8 x 25 mm (4)
520-1031
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059

6 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
• Never mount this product to metal studs without the
requiredaccessory.
• Installermustverify that the supporting surface willsafelysupportthe combined load of the equipmentandallattached
hardwareandcomponents.
• Tightenwoodscrews so that wall plate is firmlyattached,butdonot overtighten. Overtightening can damage the
screws,greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal
studs (contact customer care). Metal stud installation is not UL evaluated.
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovidedisfor attachment of mount through standard thickness drywall or plaster intowoodstuds.Installers
areresponsibletoprovidehardwareforothertypesofmountingsituations.
• Neverexceedthe Maximum UL Load Capacity of175lb(79 kg).
1
WARNING
Installation to Wood Stud Wall
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the
studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line
down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .36"
abovethedesired screen center for PLA60-UNL, PLA60-UNL-S,PLA60-UNLP,PLA60-UNLP-S, RTPLA60
RTPLA60-S and .43" below the desired screen center for PLAV60-UNL,PLAV 60-UNL-S, PLAV60-UNLP,PLAV
60-UNLP-S,RTPLAUN7, RTPLAUN7S, D-FPA-320,andD-FPA-320S. Level plate,andmark the center of the
eight mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill eight 7/32" dia. holes
3" deep. Make sure that the wall plate is level, secure it using eight 5/16 x 3" wood screws (O) and washers (P).
Skip to step 2 on page 8.
A
O
P
WARNING

7 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
IMPORTANT!Concrete mustbe 2000 psidensity minimum.
Use wall plate (A), making sure that it is level, as a
template to mark holes. The top mounting slots should
be located .36" above the desired screen center for PLA
60-UNL,PLA60-UNL-S,PLA60-UNLP,RTPLA60,PLA
60-UNLP-SandRTPLA60-Sand.43"belowthedesired
screencenterforPLAV60-UNL,PLAV60-UNL-S,PLAV
60-UNLP,PLAV60-UNLP-S,RTPLAUN7,RTPLA
UN7S,D-FPA-320andD-FPA-320S.Usethemasonry
bit to drill 5/16" (8 mm) dia. holes to a minimum depth of
3" (76 mm). Insert anchors (W) in holes flush with wall as
shown(right).Place wallplate(A)over anchors(W)and
secure with 5/16 x 3" wood screws (O) and washers (P).
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardwareandcomponents.
• Neverexceedthe Maximum UL Load Capacity of175lb(79 kg).
• Never mount this product to metal studs.
WARNING
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattachconcreteexpansionanchorstoconcrete
coveredwithplaster,drywall,orotherfinishingmate-
rial.Ifmountingto concrete surfaces covered with a
finishingsurfaceisunavoidable,thefinishingsurface
mustbecounterboredasshown below.Ifplaster/
drywall is thicker than 5/8", custom fasteners must be
suppliedbyinstaller(NotevaluatedbyUL).
WARNING
• Tighten wood screws so that wall plate is firmly
attached,butdonotovertighten.Overtighteningcan
damagescrews,greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
1
Installation to Concrete Wall
A
OP
W
1-4
1-1
1-3
1-2
concrete
surface
Drill hole(s) and insert anchor(s) (W)
mounting
plate
Place plate over anchor(s) (W) and secure with screw(s)(O)
Tighten all fasteners
W
W
CUTAWAYVIEW
INCORRECT CORRECT
mounting
plate
plaster/
drywall
concrete mounting
plate concrete
plaster/
drywall

8 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown.Cable ties (S) are used
withclipsfor cord management.
Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.
R
S
C
3
T
3-1
KD
N
J
D
M
J
C
DETAIL 3
A
Note: There are five mounting positions. The
center position is shown (right). Slidewasher(J)
over wall support arm axle (D). Next, insert plastic
cap (N) into axle. Then, insert holding pin (M) into
axle. See detail 1.
Note: Fit of axle (D) into wall plate (A) and arm
assembly (C) will be tight. Gently tap into place
with a hammer if necessary.
2
2-1
Insert socket cap screw (K) into hole at bottom of
wall support arm axle (D) as shown in detail 3.
Tightenscrewusing9/64"allenwrench(Q).
Place arm assembly (C) with washer (J) into wall
plate (A). Insert axle assembly shown in detail 1
throughwallplate (A), arm assembly (C), and
washer (J). Lock axle in place by aligning holding
pin (M) with notches shown in detail 2.
2-2
DETAIL 1
NOTCH
DETAIL 2
• If you are uncertain that product is properly installed, call customer care.
WARNING

9 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
B
I
F
Insert and tape carriage bolt (I) into top hole of pitch-roll assembly (B).Attach tilt-roll assembly to adapter
bracket (AA) with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).
• Donotovertightenscrews!Overtightening may hinder
rolloption.
CAUTION
4
5
Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm
assembly(C).
4-1 Insertone finishing cap (L) intoeachunused hole of wall plate (A).
LA
E
SWIVELBOX
C
AA

10 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.
.25"
F
• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.
WARNING
• After tilt is adjusted, all fasteners must be tightened.
Failure to do so will result in damage to the mount.
CAUTION
6
6-1
6-2
fig. 6.1 fig. 6.2
SWIVELBOX
Hook tilt-roll assembly (B) onto M10 screws (F).
Insert carriage bolt (I) into slot of swivel box as
shown in figure 6.1. Install nylon washer (G) and tilt
adjustmentknob(H).
Install remaining two M10 screws (F) as shown in
figure6.2.HANDTIGHTENallfourM10screwsto
allowfortiltadjustment.Removetapefromcarriage
bolt (I). For tilt adjustment, push back on the top of
plasma to relieve pressure on knob.Adjust tilt to
desired position and tighten tilt adjustment knob (H),
then securely tighten all four M10 screws (F) using 6
mmallenwrench(U).
I
BF
H
G
SWIVELBOX
H
F
I
C
Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

11 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Note: "X"dimensionsshouldbeequal.
Installing Adapter Brackets
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown below.
Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers,
andspacers as shown infigure 7.1 and figure7.2.
Note: Top and bottom holes on screen must always be used.
Verifythatallholesareproperlyaligned,and then tighten screws using aphillips screwdriver.
Note: If using security screws, tighten using security allen wrench (DD).
MEDIUMHOLEFORM5SCREWS
SMALLHOLEFORM4SCREWS
LARGEHOLEFORM6SCREWS
BB
or
CC
CENTERBRACKETSVERTICALLY
ONBACKOFSCREEN
X
X
Notes:
• Thenumberoffastenersusedwillvary,
dependinguponthetypeofscreen.
• Multi-washers and spacers may not be
used,dependinguponthe type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MULTI-WASHER
7
• Tightenscrewsso adapter brackets are firmly attached. Donottightenwith excessive force. Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
NOTE: For flat back screens proceed to step 7-1. For bump-out or recessed back screen skip to step 7-2

12 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2
for a full screen compatibility chart for this mount.
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.
If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.
Repeatfor remaining mounting holes,levelbrackets and tighten screws.
NOTE: Spacers may not beused, depending upon the typeofscreen.
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2
for a full screen compatibility chart for this mount.
Beginwith longer length screw, hand threadthrough multi-washer,adapter bracket and spacerinthatorderinto
screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do
not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled
fastenerpack. Repeat for remainingmounting holes, level bracketsand tighten screws.
For Flat Back Screen
For Bump-out or Recessed Back Screen
SCREEN
MULTI-WASHER
SCREW
ADAPTER
BRACKET
(BBORCC)
fig. 7.2
SPACER
fig. 7.1
7-1
7-2
ADAPTER
BRACKET
(BBORCC)
SCREEN
MULTI-WASHER
SCREW
Ifyouhaveanyquestions, please call Peerless customer care at 1-800-865-2112.
Ifyouhaveanyquestions, please call Peerless customer care at 1-800-865-2112.

13 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Mounting and Removing Flat Panel Screen
Referto mount instruction sheetfor attachment of adapterbracket to mount.
Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turnscrews
clockwiseatleastsixtimestopreventscreenfrombeingremovedasshownindetail4.Tightenusingallenwrench(DD).
Screen can be adjusted horizontally if desired.
Note: To lock the screen down, tighten screws to adapter bracket as shown in detail 4.
Toremovescreen frommount,loosenscrews, swingscreenawayfrom mount,andliftscreenoffofmount.
8
AA
BB or CC
DETAIL 4
SCREWS
AA
BB
or
CC
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING

14 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Position of screen may be adjusted vertically up to
.79" in each direction by doing the following:
• To lower screen, turn socket screw shown in figure
10.1 clockwise with 10 mm allen wrench (V).
• To raise screen, turn socket screw shown in figure
10.1 counterclockwise with 10 mm allen wrench (V).
If it is too difficult to adjust roll of plasma, loosen
screws shown in figure 9.1 using a phillips screw-
driver.
IMPORTANT! Donotloosen or tighten screws
morethan 1/8 turn.
Depending on the specific size & weight of the plasma,
articulatingswingarmmay be angled at different
positions, causing plasma to appear to lean sideways
atdifferentarticulatingpositions.Tilt-roll assembly (B)
allows plasma to be manually adjusted, so plasma can
be horizontal at all positions.To adjust, gently rotate
plasma by hand to desired position.
FOR PLAV 60 ONLY:
99-1
ARTICULATING
ARM
PLASMA
10
SOCKET
SCREW
fig. 10.1
fig. 9.1
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
ROLL
ADJUSTMENT
SCREWS

Modèles : PLA 60-UNL, PLA 60-UNL-S,
PLA 60-UNLP, PLA 60-UNLP-S,
PLAV 60-UNL, PLAV 60-UNL-S,
PLAV 60-UNLP, PLAV 60-UNLP-S
RTPLA 60, RTPLA 60-S, RTPLA UN7,
RTPLA UN7S, D-FPA-320, D-FPA-320S
Installation et montage - Support mural articulé
universel pour écrans plasma de 37 à 60 po
Capacité de charge maximale préconisée
par UL: 175 lb (79 kg)
R
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
Ce produit est homologué UL. Il
doit être installé par uninstallateur
professionnel qualifié.

16 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
Outils nécessaires au montage
•localisateur de montants (un localisateur de montants
« bordà bord » est recommandé.)
•perceuse
•foret de 7/32 po pour montants en bois
•foretà maçonnerie de 5/16 popour béton
•cléà douille de 7/16 poavec extension (recommandé)
•niveau
•tournevisPhillips
Accessoires
•Plaquemurale extérieure (WSP716, WSP716-S,
WSP724, WSP724-S) (Le montant métallique n’a pas
étéévaluéparl’UL)
Remarque : lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
• Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en garde
contenues dans cette fiche d’installation. Pour toute question concernant les instructions ou les mises en garde,
appelezleserviceàlaclientèledePeerlessau1-800-865-2112.
• Ceproduitne doit être installé que par une personne ayantdebonnesaptitudesen mécanique, expérimentée en
travauxdeconstructionélémentaires,etdémontrant une parfaite compréhension de ces instructions.
• Assurez-vousquelasurface de support pourra soutenir sans danger la charge combinée del’équipement,detoutesa
visserie et de tous ses composants.
• Ne dépassez jamais la capacité de charge maximum établie par l’UL. Reportez-vous à la page 17.
• Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au
centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.
• Pourleveretpositionnerl’équipemententoutesécurité,faites-voustoujours aider par une autre personne ou utilisez
unmatérieldelevagemécanique.
• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire
considérablementlepouvoirdemaintien.
• Ce produit a été conçu et prévu pour être monté sur les surface de support mentionnées ci-après ; la visserie incluse
dans ce produit est celle spécifiée sur la fiche d’installation. Pour monter ce produit sur une autre surface de support,
adressez-vousauserviceclientèledePeerless au 1-800-865-2112.
• Ce produit a été conçu pour être installé sur le type de mur suivant uniquement :
TYPEDEMUR VISSERIE SUPPLÉMENTAIRE REQUISE
xMontantenbois Aucune
xPoutreenbois Aucune
xBétonplein Aucune
xBlocdebétonde mâchefer Aucune
Montantmétallique Ne fixer qu’avec le kit d’accessoires Peerless pour montants métalliques
Adressez-vousauserviceclientèlepourvousprocurerlekitd’accessoires
Peerlesspourmontantsmétalliques.
Brique Adressez-vousauserviceclientèle
Autre, ou vous n’êtes pas sûr ? Adressez-vousauserviceclientèle
AVERTISSEMENT
Table des matières
Liste des pièces .................................................................................................................................................................17
Installation sur un mur à doubles montants en bois ............................................................................................................20
Installation sur du béton plein ou un bloc de béton de mâchefer .........................................................................................21

17 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
S
E
F
D
Liste des pièces du
support mural
K
M
C
A
H
BJ
N
L
Q
Certaines pièces peuvent différer légèrement de l’illustration.
G
I
Avant de commencer, veuillez vous assurer que toutes les pièces énumérées sont incluses.
O
P
UV
RTPLA 60 RTPLA 60-S
RTPLA UN7 RTPLA UN7S
D-FPA-320 D-FPA-320S
WT
R
PLA60-UNL PLA60-UNL-S PLAV60-UNL PLAV60-UNL-S
PLA60-UNLP PLA60-UNLP-S PLAV60-UNLP PLAV60-UNLP-S
Descripción Cant.Nº de pieza Nº de pieza Nº de pieza Nº de pieza
Aplaquemurale 1 201-1040 201-4040 201-1040 201-4040
B support inclinable et rotatif 1 201-1093 201-4093 201-1048 201-4048
Cbrasarticulé 1 201-1072 201-4072 201-1049 201-4049
Daxedusupportmural 1 201-1041 201-1041 201-1041 201-1041
Ebordureenvinyle 3 600-1012 600-1012 600-1012 600-1012
Fboulon à vis M10 x 1,5 x 15 mm 8 520-9262 520-9262 520-9262 520-9262
Grondelle 0,505 x .75 x 0,062 po 1 540-1074 540-1074 540-1074 540-1074
Hmolette 1 560-0108 560-0108 560-0108 560-0108
Iboulon 3/8 -16 x 3,25 po 1 520-1315 520-1315 520-1315 520-1315
Jrondelle 1,525 x 2 x 0,062 po 2 540-1070 540-1070 540-1070 540-1070
Kvis d’assemblage à tête creuse 1 520-1210 520-1210 520-1210 520-1210
Lemboutdefinition enplastique 8 590-1123 590-1123 590-1123 590-1123
Mtige de fixation 1 580-1166 580-1166 580-1166 580-1166
Nbouchondesûreté 1 590-1007 590-1007 590-1007 590-1007
Ovis à bois de 5/16 x 3 po 8 520-1243 520-1243 520-1243 520-1243
Prondelle de 0,250 x 1 x 0,068 po 8 540-1063 540-1063 540-1063 540-1063
Qcléhexagonale de 9/64 po 1 560-9728 560-9728 560-9728 560-9728
Rserre-câble 4 590-1166 590-1166 590-1166 590-1166
Sattache de câble 4 590-1168 590-1168 590-1168 590-1168
Tenveloppeenmaillepolyester 1 600-1015 600-1015 600-1015 600-1015
Uclé hexagonale de 6 mm 1 560-9716 560-9716 560-9716 560-9716
Vcléhexagonalede 10 mm 1 n/a n/a 560-9727 560-9727
Wchevilled’ancrage 8 590-1025 590-1025 590-1025 590-1025

18 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
DD
CC
BB
AA
D-FPA-320 D-FPA-320S
RTPLA UN7 RTPLA UN7S
RTPLA 60 RTPLA 60-S
PLA 60-UNL PLA 60-UNL-S PLA 60-UNLP PLA 60-UNLP-S
PLAV 60-UNL PLAV 60-UNL-S PLAV 60-UNLP PLAV 60-UNLP-S
Description Qté Pièce nº Pièce nº Pièce nº Pièce nº
AA support adaptateur 1 201-1110 201-4110 201-1110 201-4110
BB support adaptateur peu profond 2 201-1511 201-4511 201-1514 201-4514
CC support adaptateur profond 2 201-1510 201-4510 201-1513 201-4513
DD clé hexagonale 1 560-9646 560-9646 560-0072 560-0072
Avant de commencer, veillez à ce que toutes les pièces énumérées soient incluses.
Liste des pièces

19 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211
rondelle tout
usage(6)
580-1036
Fixations de sécurité du support adaptateur
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 rondelle tout
usage (6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Fixations Phillips du support adaptateur
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208 M8 x 25 mm (4)
520-1031
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059

20 of 42 ISSUED: 06-05-06 SHEET #: 202-9141-7 05-06-08
• L’installateur doit s’assurer que la surface de support puisse soutenir sans danger la charge totale de l’équipement
ainsi que des pièces et composants qui y sont attachés.
• Serrez fermement les vis à bois pour que la plaque murale tienne solidement en place, mais sans excès. Un serrage
excessifpeutendommagerlesvisetenréduireconsidérablementlepouvoirdemaintien.
• Ne serrez jamais à plus de 80 po-lb (9 Nm).
• Ne pas monter directement sur un mur à montants métalliques. Il est nécessaire d’utiliser une plaque murale WSP
afin de fixer le support à des montants métalliques (veuillez vous adresser au service à la clientèle). L’installation sur
montantsmétalliques n’a pas étéévaluée par l’UL.
•Assurez-vous que les vis de montage sont fixées au centre des montants. L’utilisation d’un localisateur de montants
"bordàbord"estfortementrecommandée.
• Les pièces de fixations fournies sont prévues pour une installation du support sur des montants en bois à travers une
cloison sèche ou du plâtre d’épaisseur standard. Il est de la responsabilité de l’installateur de fournir les pièces de
fixationrequises pour tout autretype d’installation.
• Ne dépassez jamais la capacité de charge maximum de 175 lb (79 kg) établie par l’UL.
1
AVERTISSEMENT
La plaque murale (A) peut être installée à deux montants espacés de 16 po. Repérez le bord des montants à
l’aide d’un localisateur de montants. L’utilisation d’un localisateur de montants « bord à bord » est fortement
recommandée.Après avoirrepéré les bords, tracez uneligne verticale le long ducentre de chaque montant.
Posez la plaque murale sur le mur et utilisez-la comme gabarit. Les fentes de montage supérieures doivent être
situées à 0,36 po au-dessus de l’endroit souhaité pour le centre de l’écran pour les modèles PLA 60-UNL, PLA
60-UNL-S,PLA60-UNLP,RTPLA60, PLA60-UNLP-S RTPLA60-S, RTPLAUN7,RTPLAUN7S, D-FPA-320,et
D-FPA-320S et à 0,43 po sous l’endroit souhaité pour le centre de l’écran pour les modèles PLAV 60-UNL, PLAV
60-UNL-S, PLAV 60-UNLP et PLAV 60-UNLP-S. Mettez la plaque à niveau et marquez le centre des huit trous
de fixation. Veillez à ce que les trous de fixation soient sur la ligne médiane du montant. Percez huit trous de 7/
32 po de dia. et de 3 po de profondeur Veillez à ce que la plaque murale soit de niveau et fixez-la à l’aide de huit
vis à bois de 5/16 x 3 po (O) et des rondelles (P).
.Passez à l’étape 2 à la page 22
A
O
P
Installation sur des murs à montants en bois
AVERTISSEMENT
• N’installez jamais ce produit sur des montants
métalliques sans les accessoires requis.