peerless-AV SA752PU Guide

Models: SA752PU / PEWS350/BK
Installation and Assembly:
Universal Articulating Arm Wall Mount for 32" to 52" Flat Panel
Displays
ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity: 90 lb (41.82 kg)

2 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.............................................................................................................................................................................3, 4
Wall installation...................................................................................................................................................................5, 6
Installing Adapter Brackets to Display ...............................................................................................................................7-11
Mounting Flat Panel Display.................................................................................................................................................12
Cable Management ..............................................................................................................................................................14
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• 5/32" (4mm) drill bit for wood studs
• 5/16" (8mm) drill bit for concrete and cinder block
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Metal Stud Contact Qualified Professional (not evaluated by UL)
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional
WARNING

3 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
B
CDE FG
H
JK
IM
A
SA752PU
Description Qty. Part #
Awall arm assembly 1 095-P1715
Buniversal adapter bracket 1 095-P1635-2
Cwood screws 3 520-1202
Dconcrete anchors 3 590-0320
EM10 x 15 mm socket head screw 2520-9262
Ffastener caps 3590-1324
Gcable ties 8590-1168
H6 mm allen wrench 1 560-9716
I5 mm allen wrench 1 560-9640
Jrear cable cover 2 590-P1326
Kfront cable cover 2 590-P1327
L#3 screwdriver bit (not shown) 1 560-0209
M5/32 allen wrench 1 560-9646
Parts List
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.

4 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Adapter Bracket Fasteners
M4 x 12mm (6)
(504-9013)
M4 x 25mm (4)
(504-1015)
M5 x 12mm (4)
(520-1027) M5 x 25mm (4)
(520-9543)
M8 x 16mm (6)
(520-9257)
M8 x 40mm (4)
(520-1136)
M8 x 25mm (4)
(520-1031)
I.D. .34" (4)
(540-1059)
I.D. .22" (4)
(540-1057)
M6 x 30mm (4)
(510-9109)
M6 x 12mm (4)
(520-1128) M6 x 25mm (4)
(520-1208)
M6 x 20mm (4)
(520-9402)
multi-washer (6)
(580-1036)

5 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Using a stud finder, locate and mark the edges of the wood stud. Use a level to draw a vertical line down the center
of the stud and mark the desired display center. Use wall plate template (wall arm) to mark center of holes along
the vertical line. The top mounting hole should be 7.54" (192mm) above the desired display center as shown in
figure 1.1. Drill three 5/32" (4mm) dia. holes to a depth of 2.5" (64mm). Attach wall arm (A) to wall with three wood
screws (C) using #3 phillips screwdriver bit (L) as shown in fig. 1.2. Level then tighten all fasteners.
Insert three fastener caps (F) into wall plate mounting holes.
Installation to Single Wood Stud Wall
1
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING
7.54"
(192mm)
CS = CENTER OF DISPLAY
WOOD STUD
C
F
A
WOOD STUD
WALL PLATE
CS
fig. 1.1
fig. 1.2

6 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Installation to Solid Concrete or Cinder Block
Mark the desired display center and use wall plate
template (wall plate) to mark mounting holes.The top
mounting hole should be 7.54" (192mm) above the
desired display center as shown in figure 1.1 on page
5. Drill three 5/16" (8mm) dia. holes 2.5" (64mm) deep
as shown in fig. 1.3. Insert anchors (D) into holes flush
with wall. Place wall arm (A) over anchors and secure
with three wood screws (C) using #3 screwdriver bit
(L). Level then tighten all fasteners.
Insert three fastener caps (F) into wall plate mounting
holes.
D
1
A
fig. 1.3
C
F
1
3
2
D
Drill holes and insert anchors (D).
Place wall arm (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
A
D
C
concrete
surface
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable (not
evaluated by UL), the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16mm), custom fasteners must be supplied by
installer (not evaluated by UL).
WARNING
SOLID CONCRETE
CINDER BLOCK
WALL PLATE

7 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
NOTE: If display has a VESA 400 horizontal
mounting pattern, skip to step 2-3 or 2-4 on page 9.
NOTE: For VESA 200x200 or VESA 200x100
mount hole patterns, skip to step 3 on page 10.
NOTE: For dedicated PLP plate installation skip to
step 4 on page 12.
Remove four 1/4-20 x .6" screws using 5mm allen
wrench (I) and loosen two 1/4-20 x 1.25" screws
1/2 turn to allow for display bracket adjustment.
1/4-20 x .6" SCREWS
1/4-20 x 1.25" SCREWS
2
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down and refer to display manufacturers instructions for removing obstructions from the
back of the display. Adjust display brackets to align with display mounting holes.
Measure horizontal mounting hole pattern and choose fixed stop-position from chart below.
2-1
FIXED STOP-POSTION #2
FIXED STOP-POSTION #1
FIXED STOP-POSTION #3
horizontal mounting hole pattern fixed stop-position
10-3/4" - 16-1/16" (273 - 408 mm) #1
15-1/16" - 21-9/16" (383 - 548 mm) #2
20-7/16" - 27-9/16" (519 - 700 mm) #3
Installing Adapter Brackets to Display

8 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Select the screws from the baffled fastener pack that best fit your display and secure to display following step 2-3
or 2-4 on page 9.
NOTE: Top and bottom mounting holes must be used for attaching display brackets. Middle holes should also be
used where the fasteners and displays allow.
Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.
CENTER DISPLAY BRACKETS VERTICALLY AND
HORIZONTALLY ON BACK OF DISPLAY
DISPLAY
DISPLAY BRACKETS
NOTE: "X" dimensions should be equal.
"Y" dimensions should be equal.
• Tighten screws so display brackets are firmly attached to display. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing
screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
YY
X
X
2-2
Installing Adapter Brackets to Display

9 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Begin with the shortest length screw, hand thread
screw through multi-washer and display brackets
(B) into display as shown below. Screw must make
at least three full turns into the mounting hole and
fit snug into place. Do not over tighten. If screw
cannot make three full turns into the display, select
a longer length screw from the baffled fastener
pack. Repeat for remaining mounting holes, level
display brackets and tighten screws.
NOTE: Spacers may not be used, depending upon
the type of display.
Skip to step 2-5.
Begin with the longest length screw, hand thread
screw through multi-washer, display brackets (B)
and spacer in that order into display as shown
below. Screw must make at least three full turns
into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three
full turns into the display, select a shorter length
screw from the baffled fastener pack. Repeat for
remaining mounting holes, level display brackets
and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
2-3
2-4
DISPLAY
MULTI-WASHER
SCREW
B
DISPLAY
MULTI-WASHER
SPACER
B
SCREW
Center display brackets horizontally and vertically
on back of display. Tighten two 1/4-20 x 1.25"
screws. Reinstall four 1/4-20 x .6" screws using
5mm allen wrench (I) into appropriate fixed-stop
position from chart on page 7.
2-5 1/4-20 x 1.25" SCREWS
1/4-20 x .6" SCREWS

10 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Remove four 1/4-20 self tapping screws to detach display brackets from outer mount holes of universal adapter
bracket (B) using 5mm allen wrench (I) as shown in figure 3.1. Reinstall four 1/4-20 self tapping screws to secure
display brackets to inner set of mounting holes on universal adapter bracket (B) as shown in figure 3.2.
1/4-20 SELF
TAPPING SCREWS 1/4-20 SELF
TAPPING SCREWS
Display
BRACKETS Display
BRACKETS
INNER
MOUNTING
HOLES
OUTER
MOUNTING
HOLES
fig. 3.1 fig. 3.2
VESA 200 x 200 or VESA 200 x 100 Mounting Pattern
To prevent scratching the display, set a cloth on a
flat, level surface that will support the weight of the
display. Place display face side down and place
universal adapter bracket (B) onto display.
3-1
3
BB
B
1/4-20 x .6" SCREWS
1/4-20 x 1.25" SCREWS
Remove four 1/4-20 x .6" screws using 5mm allen wrench
(I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to allow for
display bracket adjustment.

11 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Slide universal adapter bracket to the opposite side
and align second display bracket with second set of
display mounting holes.
Hand thread screws through multi-washer, display
bracket, and spacer if used, into display as shown.
Tighten all screws.
3-3
SCREW
MULTI-WASHER
MULTI-
WASHER
DISPLAY DISPLAY
BRACKET
VESA 200 x 200 or VESA 200 x 100 Mounting Pattern (Continued)
Align one display bracket with one set of display
mounting holes.
Begin with the shortest length screw, hand thread
screw through multi-washer and display brackets
into display as shown. Screw must make at least
three full turns into the mounting hole and fit snug
into place. Do not over tighten. If screw cannot
make three full turns into the display, select a longer
length screw from the baffled fastener pack. Center
display brackets vertically and tighten screws.
NOTE: For displays with a bump-out or recessed
back, spacer may be used. Spacer goes between
display bracket and display.
3-2 SCREW DISPLAY
DISPLAY
BRACKET
Center display brackets horizontally on back of display as shown in figure 3.3.
Tighten two 1/4-20 x 1.25" screws. Reinstall four 1/4-20 x .6" screws using 5mm allen wrench (I) into fixed-stop
position 1 as shown in figure 3.4.
3-4
fig. 3.4
1/4-20 x 1.25" SCREWS
FIXED STOP POSITION #1 WITH
1/4-20 x .6" SCREWS
fig. 3.3

12 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
For Dedicated PLP Plate (not evaluated by UL):
Refer to PLP model instruction sheet for attachment
of dedicated PLP plate to display.
Install two M10 x 15mm screws (provided with
dedicated PLP plate) into top two holes of dedicated
PLP plate leaving 1/4" of exposed thread as shown
in figure 4.1.
Insert two M10 x 15mm screws (E) into bottom holes of adapter plate as shown in figure 4.3 or 4.4. Tighten all
fasteners with 6mm allen wrench (H).
4-1
A
B
B
E
ADAPTER PLATE
ADAPTER PLATE
DISPLAY NOT
SHOWN FOR
CLARITY
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handle placement of the display.
• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten M10 x 15mm
screws (E) to 40 in. • lb (4.52 N.M.) maximum torque.
WARNING
Mounting Flat Panel Display
4
1/4"
M10 X 15MM SCREW
1/4"
M10 X 15MM SCREW
DEDICATED PLP PLATE
ADAPTER PLATE
fig. 4.1
fig. 4.2
E
DEDICATED PLP PLATE
ADAPTER PLATE
fig. 4.4fig. 4.3
For Universal Adapter Bracket: Hook M10 x 15mm
screws into keyslots of wall arm adapter plate (A) as
shown figure 4.2.

13 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
FOR PORTRAIT OR LANDSCAPE DISPLAY ORIENTATION: Remove two M5 x 12mm screws, one M5 x 6mm
screw and rotation block from top of tilt head as shown in top view and rear view. Gently grasp sides of display and
rotate display into portrait or landscape position as shown in figure 5.1 and reinstall rotation block with two
M5 x 12mm screws and one M5 x 6mm screw. NOTE: M5 x 6mm screw required in landscape orientation only.
Tilt Adjustment: Adjust tension knob on side of
mount to desired tension to enable tilt adjustment and
balance your display size and weight. Push or pull
from top or bottom of display to adjust tilt as shown.
The tilt can be adjusted to a maximum of 10° forward
or 5° backward. Retighten tension knob. NOTE: For
larger displays, tension screw on opposite side of
mount may need to be tightened using 5/32" allen
wrench (M).
Roll Adjustment: Rotate display 5° clockwise or
counter-clockwise, level display then tighten
M5 x 10mm screws using 5mm allen wrench (I) as
shown in detail 1.
Vertical Height Adjustment: Tighten or loosen two
M8 x 40mm screws an equal number of turns to
achieve ± 1" of vertical height adjustment as shown in
detail 1.
Adjustment of Flat Panel Display
5
6
TENSION KNOB
DETAIL 1
REAR VIEW
TOP VIEW
fig. 5.1
M5 X 10MM
SCREWS
M8 X 40MM
SCREWS
• Do not tighten screws with excessive force.
• Be careful not to pinch fingers when opening and
closing mount from the wall.
CAUTION
• M10 x 15mm screws (E) must be securly tightened before changing orientation of wall arm (A). Failure to lock
adapter bracket can cause display to come off of mount.
WARNING
ROTATION BLOCK
ROTATION BLOCK
M5 X 12MM SCREWS
M5 X 6MM SCREWS
M5 X 12MM
SCREWS
M5 X 6MM
SCREWS

14 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
If more or less tension is desired in the arm pivot points, do the following:
• To increase tension, turn socket screw clockwise with 5mm allen wrench (I). NOTE: Tighten screws to
50 in • lbs (5.6 N.m.) maximum torque.
• To reduce tension, turn socket screw counter-clockwise with 5mm allen wrench (I). NOTE: Do not turn more
than half a turn.
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Cable Management
NOTE: Make sure cables have enough slack to allow full movement of the arm.
Run power cable through top or bottom of wall arm (A) and signal cable(s) through other side of arm in order to
avoid interference with the signal. Lock cables into place by snapping cable covers (J & K) onto mount. Display
may have to be moved for easy access.
Optional: If additional cable management is required route cable ties (G) through slots of wall arm (A) as shown in
detail 3.
7
8
A
G
K
J
CABLE
TENSIONS SCREWS
TENSIONS SCREW
DETAIL 3
SLOT
• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the display
to fall.
• If screws become loose over time, tighten screws as necessary. Tighten screws to 50 in • lbs (5.6 N.m.) maximum
torque.
WARNING

Modelos: SA752PU / PEWS350/BK
Instalación y montaje:
Soportes de pared de brazo articulador para pantallas planas
de 32" a 52"
PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Máxima capacidad de carga para UL: 90 lb (41.82 kg)

16 de 58 PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
Español
Tabla de Contenido
Lista de piezas................................................................................................................................................................17, 18
Instalación en una pared ................................................................................................................................................19, 20
Instalación del soporte adaptador universal....................................................................................................................21-25
Instalación de la pantalla plana ............................................................................................................................................26
Manejo de los cables............................................................................................................................................................28
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las ad-
vertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente
internacional, por favor, comuníquese con su distribuidor local.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga experien-
cia en construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los fi-
jadores y componentes.
• Nunca sobrepase la capacidad máxima de soportar carga aceptada por Underwriters Laboratories. Vea la página 15.
• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén
anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
con más seguridad.
• Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede disminu-
ir significativamente su fuerza de fijación.
• Este producto está diseñado para uso en interiores solamente. Utilizar este producto en exteriores podría causar fal-
las del producto y lesiones a individuos.
• Este producto fue diseñado para ser instalado en paredes con la siguiente construcción solamente:
CONSTRUCCIÓN DE LA PARED ACCESORIOS NECESARIOS
• Montante de madera Incluido
•Viga de madera Incluido
•Concreto macizo Incluido
•Bloque de hormigón de escorias Incluido
•Montante de metal No lo instale excepto con el juego de accesorios de Peerless para
montantes de metal (no evaluados por UL)
•Ladrillo Comuníquese con un profesional calificado (no evaluados por UL)
•¿Otra superficie o no está seguro? Comuníquese con un profesional calificado
ADVERTENCIA
NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
Herramientas necesarias para el ensamblaje
•localizador de montantes (se recomienda uno de "borde a borde")
•destornillador phillips
•broca de 5/16" (8mm) para paredes de concreto y de bloque de hormigón de escorias
•broca de 5/32" (4mm) para paredes con montantes de madera
•nivel

17 de 58 PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
Español
B
CDE FG
JK
A
Las piezas pueden verse un poco distintas a la ilustración.
Antes de empezar, asegúrese de que todas las piezas que se muestran son incluidos con su producto.
SA752PU
Descripción Cant. Nº de pieza
Abrazo de pared 1 095-P1715
Bsoporte adaptador universal 1 095-P1635-2
Ctornillos para madera 3 520-1202
Dconcreto de anclajes 3 590-0320
Etornillos de M10 x 15 mm 2520-9262
Fcubiertas para sujetadores 3590-1324
Gsujetacables 8590-1168
Hllave allen de 6 mm 1 560-9716
Illave allen de 5 mm 1 560-9640
JCubierta trasera para cables 2 590-P1326
KCubierta delantera para cables 2 590-P1327
Lista de piezas
p
LDestornillador de cabeza #3 (no ilustrado) 1 560-0209
Mllave allen de 5/32 1 560-9646
HI M

18 de 58 PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
Español
Fijaciones para los soportes adaptadores
arandela
múltiple (6)
(580-1036)
M4 x 12mm (6)
(504-9013)
M4 x 25mm (4)
(504-1015)
M5 x 12mm (4)
(520-1027) M5 x 25mm (4)
(520-9543)
M8 x 16mm (6)
(520-9257)
M8 x 40mm (4)
(520-1136)
M8 x 25mm (4)
(520-1031)
I.D. .34" (4)
(540-1059)
I.D. .22" (4)
(540-1057)
M6 x 30mm (4)
(510-9109)
M6 x 12mm (4)
(520-1128) M6 x 25mm (4)
(520-1208)
M6 x 20mm (4)
(520-9402)

19 de 58 PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
Español
Utilizando un localizador de montantes, localice y marque los bordes del montante. Se recomienda utilizar un
localizador de montantes de "borde a borde". Utilice un nivel para trazar una línea vertical por el centro del
montante y utilice la plantilla placa pared (brazo de pared) para marcar el centro de los agujeros sobre la línea
vertical. Los agujeros de montaje superiores deben estar ubicados a 7.54" (192mm) sobre el punto donde quiere
que quede el centro de la pantalla, como se muestra en la figura 1.1. Taladre tres agujeros de 5/32" (4mm)
de diámetro con una profundidad de 2.5" (64mm). Fije el brazo de pared (A) en la pared usando tres tornillos
para madera (C) con Phillips broca #3 (L), como se muestra en la figura 1.2. Nivele la placa y apriete todos los
sujetadores.
Inserte tres cubiertas para sujetadores (F) en los agujeros de montaje de la placa de pared.
Instalación en una pared con montante de madera único
1
7.54"
(192mm)
C
F
A
CP
fig. 1.1
fig. 1.2
• El instalador debe verificar que la superficie de apoyo sea capaz de soportar firmemente la carga combinada del equipo y todos
los herrajes y componentes.
• Apriete los tornillos para madera de tal modo que la placa de apoyo quede firmemente sujeta, pero no apriete en exceso. El
apriete excesivo puede dañar los tornillos, reduciendo enormemente su fuerza de fijación.
• Nunca apriete más de 80 pulg-lb (9 N•m).
• Asegúrese de que los tornillos de montaje queden bien fijos en el centro del montante. Se recomienda usar un localizador de
montantes de "borde a borde".
• Los herrajes suministrados son para fijar el soporte a través de tabique de yeso-cartón o yeso de espesor estándar a los mon-
tantes de madera. Los instaladores son responsables de suministrar los herrajes para otros tipos de situaciones de montaje (no
evaluados por UL).
ADVERTENCIA
CP = CENTRO DE LA PANTALLA
MONTANTE
MONTANTE
PLACA DE PARED

20 de 58 PUBLICADO: 10-30-09 HOJA #: 095-9297-7 07-11-11
Español
Utilice la plantilla placa pared (brazo de pared) para
marcar los puntos de los agujeros de montaje. El
agujero de montaje superior debe estar ubicado a
7.54" (192mm) sobre el punto donde quiere que
quede el centro de la pantalla, como se muestra en
la figura 1.1 de la página 19. Taladre tres agujeros
de 5/16" (8mm) de diámetro y 2.5" (64mm) de
profundidad, como se muestra en la figura 1.3.
Inserte los anclajes (D) en los agujeros a ras con
la pared, como se muestra (a la derecha). Coloque
el brazo de pared sobre los anclajes y fíjelo con los
tornillos para madera (C) con Phillips broca #3 (L).
Nivele y apriete todos los sujetadores. Inserte tres
cubiertas para sujetadores (F) en los agujeros de
montaje de la placa de pared.
D
1
A
fig. 1.3
C
F
Instalación en una pared de concreto macizo o de bloques
de hormigón de escorias
• Cuando instale soportes de pared Peerless en bloques de hormigón de escorias, verifique que tengan un mínimo de 1-3/8"
(35mm) de superficie efectiva de concreto en el agujero que va a utilizar para los anclajes de concreto. ¡No perfore en las juntas
de mortero! Asegúrese de instalar el soporte en una parte sólida del bloque, generalmente a un mínimo de 1" (25mm) del costado
del bloque. El bloque de hormigón de escorias debe ser de conformidad con las especificaciones C-90 de ASTM. Se sugiere
taladrar el agujero con un taladro eléctrico normal en velocidad lenta en vez de un taladro percutor para evitar romper la parte
trasera del agujero al entrar en un espacio o cavidad.
• El concreto debe tener una densidad mínima de 2000 psi. Un concreto menos denso podría no ser capaz de sujetar el anclaje
para concreto.
• El instalador debe verificar que la superficie de apoyo sea capaz de soportar firmemente la carga combinada del equipo y todos
los herrajes y componentes.
ADVERTENCIA
• Apriete los tornillos de tal modo que la placa de apoyo
quede firmemente sujeta, pero no los apriete en exceso.
El apriete excesivo puede dañar los tornillos, reduciendo
enormemente su fuerza de fijación.
• Nunca apriete más de 80 pulg-lb (9 N•m).
• Siempre fije los anclajes de expansión directamente al
concreto que soporta carga.
• Nunca fije los anclajes de expansión a una pared de
concreto recubierta con yeso, tabiques de yeso-cartón u
otro material de acabado. Si el montaje a superficies de
concreto recubiertas con una superficie de acabado es
inevitable (no evaluados por UL), será necesario escariar el
acabado, como se muestra más abajo. Asegúrese de que
los anclajes de concreto no se alejen del concreto al apretar
los tornillos. Si el grosor de la pared de yeso/tabique de
yeso-cartón es mayor que 5/8" (16mm), el instalador deberá
suministrar fijaciones especiales (no evaluados por UL).
ADVERTENCIA
VISTA EN CORTE
INCORRECTO CORRECTO
concreto
placa
de
pared
placa
de
pared
concreto
yeso / tabique de yeso-cartón
1
3
2
D
Taladre los agujeros y inserte los anclajes (D).
Coloque la placa de pared (A) sobre el anclaje (D) y fíjela con el
tornillo (C).
Apriete todos los sujetadores.
A
D
C
pared de
concreto
PLACA DE PARED
CONCRETO MACIZO BLOQUE DE
HORMIGÓN
DE ESCORIAS