peerless-AV Videowall Mount PD02VW 46 55 L Guide

1 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
Model: DS-VW665
Installation and Assembly:
Flat Video Wall Mount
For 40" to 65" Flat Panel Displays
Maximum Load Capacity: 125 lb (57 kg)

2 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
Table of Contents
Horizontal and Vertical Video Wall Mount Assembly Formula................................................................................................3
Parts List.................................................................................................................................................................................4
Installation to Wood Stud Wall................................................................................................................................................5
Installation to Solid Concrete or Cinder Block ........................................................................................................................6
Installing Adapter Brackets.....................................................................................................................................................7
Horizontal Adjustment and Locking Adapter Brackets............................................................................................................8
Carriage Assembly Adjustment ..............................................................................................................................................9
Adapter Bracket Adjustment................................................................................................................................................ 10
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
•drill
• 5/16"(8mm)bitforconcreteandcinderblockwall
• 5/32"(4mm)bitforwoodstudwall
• level
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• Thisproductshouldonlybeinstalledbysomeoneofgoodmechanicalaptitude,hasexperiencewithbasicbuilding
construction, and fully understands these instructions.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached
hardware and components.
• NeverexceedtheMaximumLoadCapacity.Seepageone.
• Ifmountingtowoodwallstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useof
an"edgetoedge"studnderishighlyrecommended.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• Thisproductisintendedforindooruseonly.Useofthisproductoutdoorscouldleadtoproductfailureandpersonal
injury.
• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;
WALL CONSTRUCTION HARDWARE REQUIRED
 •Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•MetalStud   ContactQualiedProfessional
•Brick    ContactQualiedProfessional
•Otherorunsure?   ContactQualiedProfessional
WARNING
Accessories
• DS-VWS0## Wall Plate Spacer Kit

3 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
H
WIDTH
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing.
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing.
Todetermineedgeofsecondmount,add(Z)toedgeofrstmount.
Vertical Spacing Location - Locating the position of the bottom row of fasteners
Horizontal Spacing Location
Vertical Location
X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2)
DISPLAY WIDTH - (35) = Z (SPACING BETWEEN MOUNTS)
Horizontal Location
DISPLAYWIDTH
DISPLAY
HEIGHT
X
Y2
Y1 .938
1.688 10.25
16.00"
20.00"
24.00"
17.50"Z
Todeterminelowermountingslotpositionofsecondmount,adddisplayheightto(Y1) or (Y2)
DISTANCEEQUALS
DISPLAYHEIGHT

4 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
ABDEF
G H I J
K M
PartsList
Description Qty. Part#
Amountassembly 1 145‐T1577
Badapterbracket2 145‐T1578
Cmeshsleeve(notshown) 1 600‐1014
DM5x10mmsocketpintype‐Fscrew 2 520‐1164
E#14x2.5"hexheadwoodscrew4 5S1‐015‐C03
Fconcreteanchor4 590‐0320
Gfenderwasher4 540‐1008
Hnylonshoulderwasher4 590‐2233
IM6x12mmsocketpinscrew 4 520‐1050
JM8x15mmsocketpinscrew4 520‐1068
K4mmallenwrench1 560‐9646
Lcabletie(notshown) 2 560‐9711
MM4x8mmsocketpinserratedwasherheadscrew4 510‐1005

5 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
E
Installation to Wall Stud
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Based on their edges, draw a vertical line down the stud center. Place mount assembly (A) on wall as a
template. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on
thestudcenterline.Drillfour5/32"(4mm)dia.holes2-1/2"(65mm)deep.Makesurethatthemountassembly
(A) is level, secure it using four #14 x 2.5” wood screws (E) and fender washers (G) as shown below.
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.
Installers are responsible to provide hardware for other types of mounting situations.
WARNING
1
A
STUD
G
SIDE VIEW
MOUNTING
SURFACE
SCREEN
DIRECTION
Note: Mount assembly (A) can
be installed to surfaces with a
maximum angle of 45°.
45°

6 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
E
F
solid concrete
cinder block
Installation to Solid Concrete or Cinder Block
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8"(35mm)ofactual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
inasolidpartoftheblock,generally1"(25mm)minimumfromthesideoftheblock.CinderblockmustmeetASTM
C-90specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhardware
and components.
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
F
Drill holes and insert anchors (F).
Place mount assembly (A) over anchors (F) and secure with
screws (E).
Tightenallfasteners.
A
F
E
concrete
surface
• Tightenscrewssothatwallplateisrmlyattached,
but do not overtighten.Overtighteningcandamage
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Alwaysattachconcreteexpansionanchorsdirectly
to load-bearing concrete.
• Neverattachconcreteexpansionanchorsto
concrete covered with plaster, drywall, or other
nishingmaterial.Ifmountingtoconcretesurfaces
coveredwithanishingsurfaceisunavoidable,
thenishingsurfacemustbecounterboredas
shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywallisthickerthan5/8"(16mm),custom
fasteners must be supplied by installer
WARNING
Make sure that video mount assembly (A) is level,
use it as a template to mark four mounting holes.
Drillfour5/16”(8mm)dia.holestoaminimum
depth of 2.5” (64 mm). Insert anchors (F) in holes
ushwithwallasshown(right).Placevideowall
mount assembly over anchors and secure with four
#14 x 2.5” wood screws (E) and fender washers (G)
as shown below. Level, then tighten all fasteners.
A
G
SIDE VIEW
MOUNTING
SURFACE
SCREEN
DIRECTION
Note: Mount
assembly (A)
can be installed
to surfaces with
a maximum
angle of 45°.
45°

7 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
Attach adapter brackets (B) to back of display using four M6 x 12 mm socket pin screws (I) with
nylon shoulder washer (H), or four M8 x 15 mm socket pin screws (J) as shown below.
NOTE: Hardware to attach dedicated plates to the mount are included with the dedicated plates.
H
I or J
2
300 mm
200 mm
PLPADAPTERPLATE
Attaching Adapter Brackets to Display
DISPLAY
B
Attach adapter brackets (B) and display onto channels on carriage assembly (A)asshowningure3.1.
Rotate lock bracket as shown in detail 1. Fasten one M4 x 8 mm socket pin serrated washer head screw (M) into
slot on mount assembly (A).
DISPLAY
A
3
FIGURE 3.1
CHANNEL
MAX VESA-600 mm
MINVESA-200mm
400 mm
DETAIL 1 LOCKBRACKET
BACK VIEW
B
M
A
SLOT

8 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
Horizontal Display Adjustment
Adapter Brackets (B) and display can be adjusted horizontally.
4
SIDE VIEW
LOCKBRACKET
LOCKBRACKET
INPLACE
USINGSECURITY
SCREW
K
Lock Display in Place
OnceAdapterBrackets(B) are in desired position, secure adapter brackets (B) using lock bracket as show below.
Loosen M4 x 8 mm socket pin serrated washer head screw (M) in slot on mount assembly (A) and rotate lock
bracket forward and up as shown in detail 2. Secure in up position using two M4 x 8 mm socket pin serrated wash-
er head screw (M).
5
M
M
M
UPPOSITION
DOWNPOSITION

9 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
Use legend below to determine position of display.
NOTE: Eachknobcanbeadjustedindependentlyfornetuningadjustments.
6
TurnknobCLOCKWISE to tighten
TurnknobCOUNTER-CLOCKWISE to loosen
Carriage Assembly Adjustment
DOWN
TurnknobCOUNTER-CLOCKWISE to move corner up
UP

10 of 10 ISSUED: 03-22-12 SHEET #: 125-9288-3 10-17-12
Visit the Peerless Web Site at www.peerless-av.com For customer care call 1-800-865-2112 or 708-865-8870.
IN OUT
TILT BACKWARD TILT RIGHT TILT LEFT
TILT FORWARD
Use legend below to determine position of display.
NOTE: Eachknobcanbeadjustedindependentlyfornetuningadjustments.
7
TurnknobCLOCKWISE to tighten
TurnknobCOUNTER-CLOCKWISE to loosen
Carriage Assembly Adjustment