peerless-AV LCT-203 Guide

Max Load Capacity: 22.5 lb (10.2 kg) per arm
Installation and Assembly:
Dual-Screen Desktop Mount for 17" to 24" Displays
Models: LCT-203
ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com

2 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Attaching VESA Plates to Display ..........................................................................................................................................4
Assembling base....................................................................................................................................................................5
Tool Needed for Assembly
• 6mm allen wrench
• phillips screwdriver
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING

3 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
Description Qty. Part #
ADual arm assembly 1 125-5357
BVESA plate 2 125-5358
Carm cover 2 125-5360
Dbase 1 125-5359
EM10 flat head socket cap screw 1 520-1743
FM10 nut 1 520-1733
GM10 split lock washer 1 520-1734
HM10 flat washer 1 520-1735
IM4 x 16mm phillips screw 8 520-1736
JM4 lock washer 8 520-1737
KM4 flat washer 8 520-1738
LM6 x 16mm socket head cap screw 2 520-1739
MM6 flat washer 2 520-1741
N5mm allen wrench 1 560-9737
Oopen end wrench 1 560-9735
Prubber feet 5 560-9736
Q#6 self-tapping screws 3 520-1742
Parts list
EFGH
IJK LM N
OP
Q
1
B
A
D
C
Fasteners and tools are located inside dual arm
assembly (A).
Slide off arm covers (C) then remove back cover of
dual arm assembly.
BACK COVER
A
C
C

4 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
Attaching VESA Plates to Display
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the screen. Place
display face side down. If display has knobs on the back, remove them to allow the VESA plates to be attached.
Tighten tilt adjustment screw to increase tension on VESA plate ball joint shown in detail 1.
Choose hole pattern as shown in detail 2.
Place VESA plates (B) on back of display. Attach VESA plates (B) to display using four M4 phillips screws (I), four
M4 lock washers (J), and four M4 flat washers (K) as shown in figure 2.1.
• Tighten screws so VESA plates are firmly attached. Do not tighten with excessive force. Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
DETAIL 2
DETAIL 1
I
B
J
K
2
fig 2.1
TILTADJUSTMENT
SCREW

5 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
Attach base (D) to arm assembly (A) using one M10
flat head screw (E), one M10 flat washer (H), one
M10 split lock washer (G), and one M10 hex nut (F).
Apply rubber feet (P) to bottom of base.
Position cables in cavity of dual arm assembly.
NOTE: Be sure connectors are in their proper
orientation. Allow enough cable slack to connect to
display.
Reattach back cover onto dual arm assembly.
NOTE: Be sure all cables are free from interference
and do not pinch power cables with back cover.
Attach VESA plates to dual arm assembly (A)
using one M6 socket head screw (L) and one M6
flat washer (M) per arm as shown below. Tighten
fasteners using 5 mm allen wrench (N).
3
5 6
4
F
A
A
G
D
H
E
M
L
P
CABLES
BACK
COVER

6 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerless-av.com
Secure back cover to dual arm assembly (A) with
three #6 self-tapping screws (Q). Slide two arm covers (C) onto dual arm assembly (A).
7 8
C
Q
AA

7 of 7 ISSUED: 04-24-12 SHEET #: 090-9209-2 05-31-12
© 2012 Peerless Industries, Inc.
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
This warranty gives specific legal rights, and you may also have other rights which vary from state to state.
LIMITED FIVE-YEAR WARRANTY
www.peerless-av.com