peerless-AV PANA-C84103 User manual

12015-06-30 #:126-9068-2 (2018-06-15)
ENG
PANA-C84103
500 lb
(227 kg)
MAX

22015-06-30 #:126-9068-2 (2018-06-15)
(13mm)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Display center.
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. The cart or stand is not
afxed or secured to the oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. This
product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal
injury. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Be careful not to pinch ngers when operating the mount. Death or
serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip
over on to the child. Relocating audio and/or video equipment to furniture not specically designed to support
audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning
onto a child. For support please call customer care at 1-800-865-2112.
WARNING

32015-06-30 #:126-9068-2 (2018-06-15)
This page was intentionally left blank
ENG

42015-06-30 #:126-9068-2 (2018-06-15)
Parts List
Part #Description Qty
Acaster, 5" swivel 4 600-0026
Bcaster support 4 145-T1799
Ccover 6 145-T1809
Dbase leg 2 145-T1767
Ehorizontal leg support 2 145-T1785
Fbase support tube 2 145-T1812
Gbase support 10 560-T1261
Hvertical leg support 2 146-T1131
Iadaptor bracket left 1 146-T1298
Jadaptor bracket right 1 146-T1299
Kcomputer cover 1 145-T1930
Lcomputer shelf 1 145-T1931
Mrail weldment 1 146-T1295
Ncord bracket 4 146-T1321
Olocking tab 4 145-TI936
PM8 x 16mm socket button screw 84 520-9527
QM8 square nut 64 530-1066
Rcover clip 24 590-0317
SM5 x 10mm type-f, socket pin screw 6 520-1164
TM5 x 12mm socket pin screw 4 520-1064
U1/4" power bit 1 560-0263
V5mm allen wrench 1 560-9640
Wlock tab 2 201-T1204
Xvertical support bracket 2 146-T1296
Y4mm allen wrench 1 560-9646
Zclip hook bracket 2 146-T1320
AA M5 x 30mm socket pin screw 2 520-1112
BB cable tie 8 560-9711
Parts (Before beginning, make sure you have all parts shown below).
D (2)
base leg
A (4)
caster B (4)
caster support
C (6)
cover
E (2)
horizontal leg
support
F (2)
base support
tube
G (10)
base support
H (2)
vertical leg
support
J (1)
adaptor
bracket right
I (1)
adaptor
bracket left

52015-06-30 #:126-9068-2 (2018-06-15)
K (1)
computer cover
P (84)
M8 x 16mm Q (64)
M8 square nut
R (24)
cover clip S (6)
M5 x 10mm
U (1)
1/4" power
bit V (1)
5mm allen
wrench
4mm allen
wrench
Y (1)
L (1)
computer shelf
W (2)
Z (2)
BB (8)
AA (2)
lock tab
clip hook
bracket
cable tie
M5 x 30mm
M (1)
rail
weldment
O (4)
locking tab
N (4)
cord
bracket
X (2)
vertical support
bracket
M5 x 12mm
T (4)

62015-06-30 #:126-9068-2 (2018-06-15)
1-1
1-2
P (4)
A
B
P (2)
Q (2)
Do not fully tighten hardware
SIDE VIEW
V
V
x4
x4

72015-06-30 #:126-9068-2 (2018-06-15)
2
P (4)
P (4)
F
F
Q (4)
Q (4)
D
Q (4)
V
x2

82015-06-30 #:126-9068-2 (2018-06-15)
3
Q(4)
G
P(4)
SIDE VIEW
TIGHTEN
CONNECTING
HARDWARE
FLUSH
EDGES
ENG
Do not fully tighten hardware
Casters must be ush to end of horizontal leg support.
ENG
V
x2
4
x8
V

92015-06-30 #:126-9068-2 (2018-06-15)
5
H
6
TIGHTEN
CONNECTING
HARDWARE
LOCK WHEELS
TIGHTEN
CONNECTING
HARDWARE
E
V
V
x2

10 2015-06-30 #:126-9068-2 (2018-06-15)
7
8
TIGHTEN
CONNECTING
HARDWARE
TIGHTEN
CONNECTING
HARDWARE
38.0"
96.5cm
E