peerless-AV Mobile Videowall Trolley PDVWM 3x3 46 55 L Guide

1 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Installation and Assembly: 3 x 3 Cart
Model: DS-VWC655-3x3
Maximum Load Capacity 1000 Ibs (454 kg)

2 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
BA
F
E
D
C
G
J
IH
KL M
N O P Q
RS T
PARTS LIST
Description Qty. Part #
A
vertical support 2 145-1543
Badapter brackets 18 145-1711
Chorizontal support 3 145-1382
Dshelf 1 145-1361
E5" caster 4 600-0026
F1/4" flat washer 48 540-9440
GM8 x 25 mm phillips screw 16 520-1031
H5/16 flat washer 16 540-9406
I5/16 split washer 16 540-9405
J1/4-20 x 3.5" hex head screw 48 520-1656
K1/4-20 nylock nut 48 530-9413
L.38 OD x .06 LG nylon washer 36 590-2233
M18" mesh sleeve 9 600-1014
NM8 x 16 mm phillips screw 36 520-9257
OM6 x 12 mm phillips screw 36 520-1128
P4 mm allen wrench 9 560-9646
Qcable tie 18 560-9711
Rtube cap 2 590-1289
SM5 x 10 mm socket pin screw (not used) 18 520-1164
T#14 fender washer (not used) 36 540-1008
Ulower front cover 1 145-1505
V
lower back cover 1 145-1384
Wupper cover 2 145-1450
X
rail connection bracket 6 145-1503
Y
horizontal rail 6 145-1447
Zside cover 2 145-1362
A
A
M5 x 10 mm phillips screw 40 520-1233
BB flat washer 40 540-9400
CC lock washer 40 540-1035
DD decorative screw 14 520-2326
EE spacer 4 590-1136
FF self-drilling screw 3 520-1320
GG connection bracket 4 145-1504
HH M6 x 16 mm phillips screw 36 520-9274

3 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
UVW
YZ
AA BB CC
DD EE FF
X
GG

4 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Assembling Cart
1Attach two horizontal supports (C) to vertical support (A) using eight 1/4-20 x 3.5" hex head screws (J),
1/4" SAE washers (F) and 1/4-20 nylock nuts (K).
2Attach horizontal supports (C) to second
vertical support (A) using eight 1/4-20 x 3.5" hex
head screws (J), 1/4" SAE washers (F) and 1/4-20
nylock nuts (K).
3Attach horizontal support (C) to vertical supports (A)
using eight 1/4-20 x 3.5" hex head screws (J),
1/4" SAE washers (F) and 1/4-20 nylock nuts (K).
A
C
J
F
K
A
C
JFK
A
C
J
F
K
A

5 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
4Attach four swivel casters (E) to vertical supports (A) using sixteen M8 x 25 mm pan phillips screws (G),
split washers (I) and 5/16" SAE at washers (H).
G
I
H
A
E
5Attach two rail brackets (Y) together using two rail connection brackets (X) with eight M5 x 10 mm pan phillips
screws (AA), lock washers (CC), and at washers (BB).
X
Y
AA
BB CC

6 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
X
X = HEIGHT OF DISPLAY
A
DISPLAY HEIGHT
DISTANCE
EQUALS
DISPLAY
HEIGHT
1. Locate the position of the lower horizontal rail assemblies and attach to vertical supports (A).
2. Use display height to determine location of upper horizontal rail assemblies,
NOTE: Horizontal rail assemblies must be secured using twenty-four 1/4-20 x 3.5" hex head screws (J).
Determine position of horizontal rails assemblies using the formula below.
6
UPPER HORIZONTAL RAIL
LOWER HORIZONTAL RAIL
HORIZONTAL RAIL ASSEMBLY

7 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
7Attach three horizontal rails assemblies onto vertical supports (A) using twenty-four 1/4-20 x 3.5" hex head screws
(J), 1/4" SAE washers (F) and 1/4-20 nylock nuts (K) as shown in detail 2. Make sure that horizontal rail
assemblies are level then tighten all 1/4-20 x 3.5" hex head screws (J). Place two tube caps (R) into tops of vertical
supports (A) as shown in detail 2. NOTE: horizontal rails must be secured using twenty-four 1/4-20 x 3.5” hex head
screws (J).
A
F
K
J
Y
A
J
J
DETAIL 2
R
CABLE MANAGEMENT
8Run display cables though top and bottom
openings in vertical supports (A) as shown.
NOTE: Display cables can be covered using
18" mesh sleeve (M) before securing.
Display cables can be secured to horizontal
rails assemblies using cable ties (Q) as needed
through slots in horizontal rails (Y).
Q
DISPLAY CABLES
M
Y
BOTTOM
OPENING
TOP
OPENING
A
Y
SLOT

8 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
9NOTE: Connection brackets (GG) orientation.
Place connection brackets (GG) onto rail connection brackets (X) as shown below.
GG
FRONT OF DISPLAY CART
FRONT OF DISPLAY CART
RIGHT SIDE
LEFT SIDE
X
X
GG

9 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
RIGHT SIDE SHOWN ABOVE
AA CC BB
GG
X
Attach connection brackets (GG) onto rail connection brackets (X) as shown below.
Secure one connection brackets (GG) with four M5 x 10 mm phillips screws (AA), lock washers (CC), and
at washers (BB) as shown below. Repeat step for remaining three connection brackets (GG).
9-1

10 of 13 ISSUED: 11-16-11 SHEET #: 125-9265-2 02-24-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Hook display and adapter brackets (B) onto horizontal rail assemblies as shown below.
NOTE: Start with bottom display.
NOTE: Once display is located in desired position, tighten security screws as shown in detail 4.
10 Attach adapter brackets (B) to back of display using four M6 x 12 mm phillips screws (O) or M6 x 16 mm Phillips
screw (HH) with nylon shoulder washer (L), or four M8 x 15 mm phillips screws (N) as shown below.
DISPLAY
B
N or O,HH
L
Adapter Bracket Mounting Patterns
11
DETAIL 4
DISPLAY NOT SHOWN FOR CLARITY
TIGHTEN
SECURITY
SCREW
400 mm
200 mm MIN
600 mm MAX
300 mm
200 mm
D
B
PLP PLATE