peerless-AV SUA737 Guide

Installation and Assembly: Peerless Ultra-Thin Articulating
Mount for 32" to 46"* Flat Panel Displays
Model: SUA737
*Display Compatibility Requirements
• Depth of display must be less than 2".
• The depth of this mount (1.29") may not provide
sufficient space for proper ventilation on some displays.
Please refer to the manufacturer's requirements for
mounting your display before installation.
• The display must have a flat mounting surface, or the
mounting holes need to be on the furthest back surface
of the display.
• Input/Output connection must be properly oriented to
accommodate mounting 1.29" from the wall.
ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity: 60 lb (27.2 kg)

2 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" (8mm) bit for concrete and cinder block wall
• 5/32" (4mm) bit for wood stud wall
• level
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Wall installation...................................................................................................................................................................4, 5
Installing Adapter Brackets to Display....................................................................................................................................6
Mounting Flat Panel Display...................................................................................................................................................7
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This mount is designed to attach the display 1.29" from the wall. Please refer to manufacturer's installation guide
recommendations for required distance from wall to avoid risk of injury or property damage.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
• Wood Beam Included
• Solid Concrete Included
• Cinder Block Included
• Brick Contact Qualified Professional (not evaluated by UL)
• Other or unsure? Contact Qualified Professional
WARNING

3 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
A
Description Qty. Part #
A
wall arm assembly 1 046-P1260
Cwood screws 2 520-1202
Dconcrete anchors 2 590-0320
EM4 x 6mm screw 2520-1006
Fsecurity driver 1560-1133
G4mm allen wrench 1560-9646
Hfastener cap 2 590-1324
Icable anchor 1 046-P1134
Jcable clip 1 046-P1138
K
cable tie 2 046-0136
LM5 x 12mm screw 4 560-1732
MM5 x 25mm screw 4 560-1733
NM6 x 12mm screw 4 560-1734
OM6 x 25mm screw 4 560-1735
PM8 x 12mm screw 4 560-1736
QM8 x 25mm screw 4 560-1737
R3/4" spacer 4 540-1059
Sflat washer 4 540-9478
Parts List
G
CDE F
HI
J
K
LMN O P Q R S

4 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down the stud’s center. Measure 4.8" (122mm) left or right from stud's
center to determine center of display mounting plate. Place wall arm (A) on wall as template, level, and mark the
center of two mounting holes. Top mounting hole will be 6.66" above the center of display mounting plate as shown
in figure 1.1.
Drill two 5/32" dia. holes to a minimum depth of 2.5". Secure wall arm (A) to wall with two wood screws (C) as
shown in figure 1.2. For cable management option, install cable anchor (I) to bottom mounting hole with wood
screw (C). NOTE: Be sure arrow is pointing up when mounting wall arm (A) to wall as shown in figure 1.1. Level,
then tighten all fasteners.
Insert two fastener caps (H) into wall plate mounting holes.
fig. 1.1
= CENTER OF DISPLAY
ARROW
DISPLAY
MOUNTING PLATE
6.66"
(169mm)
4.8"
(122mm)
A
C
H
I
Installation to Single Wood Stud Wall
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING
1
fig. 1.2

5 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
Place wall arm (A) on wall as template, level,
and mark the center of two mounting holes. Top
mounting hole will be 6.66" above the center of
display mounting plate as shown in figure 1.1 on
page 4. Drill two 5/16" dia. holes to a minimum
depth of 2.5". Insert anchors (D) into holes flush
with wall as shown. Secure wall arm (A) to wall with
two wood screws (C) as shown in figure 1.3. For
cable management option, install cable anchor (I) to
bottom mounting hole with wood screw (C).
NOTE: Be sure arrow is pointing up when mounting
wall arm assembly (A) to wall as shown in figure
1.1. Level, then tighten all fasteners.
Insert two fastener caps (H) into wall plate mounting
holes.
D
SOLID CONCRETE CINDER BLOCK
1
Installation to Solid Concrete or Cinder Block
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable (not
evaluated by UL), the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16mm), custom fasteners must be supplied by
installer (not evaluated by UL).
WARNING
A
C
H
I
fig. 1.3
1
3
D
Drill holes and insert anchors (D).
Place plate (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
2
D
A
C
concrete
surface

6 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
For VESA 200 x 200 mounting pattern
Insert two 12mm screws (L, N, O) into top two holes of display, leaving approximately 1/4" (6mm) of exposed
thread. Hook screws onto keyslots of front plate as shown.
Insert two 12mm screws (L, N, O) into bottom holes of adapter plate as shown. Tighten all fasteners.
2
FRONT PLATE
• Tighten screws so display brackets are firmly attached to display. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing
screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
2-1
1/4"
L, N, O
L, N, O

7 of 23 ISSUED: 12-15-11 SHEET #: 095-9371-2 03-08-12
Roll Adjustment
Cable Management
Adapter plate may be rolled +/- 5°. Roll locking screw may be tightened or loosened using 4mm allen wrench (G).
NOTE: Do not remove roll locking screw.
Cables may be routed using cable clip (J).
Slip cable clip (J) onto bottom of center joint as shown in figure 5.1 and secure cables to cable clip using cable tie
(K) as shown in figure 5.2.
Secure cables to cable anchor (I) using cable tie (K) as shown below.
4
5
JOINT SCREWS
ROLL LOCKING SCREW
fig. 5.1
J
CENTER
JOINT
fig. 5.2
K
CABLES
• Do not tighten joint screws. Doing so may cause
damage to screws, greatly reducing their holding
power.
CAUTION
I
K
CABLES
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerlessmounts.com

* Requisitos para la compatibilidad de las pantallas
• La profundidad de la pantalla tiene que ser menos de 2".
• Es posible que la profundidad del soporte (1.29") no
proporcione suficiente espacio para la ventilación
adecuada de algunas pantallas. Por favor, repase los
requisitos del fabricante en relación con la instalación de
la pantalla antes de proceder.
• La pantalla tiene que tener una superficie plana para la
instalación o tiene que tener los agujeros de montaje en
la superficie trasera más alejada de la pantalla.
• La conexión de entrada / salida tiene que tener la
orientación adecuada para acomodar una instalación a
1.29" de la pared.
PUBLICADO: 12-15-11 HOJA #: 095-9371-2 03-08-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Máxima capacidad de carga para UL: 60 lb (27.2 kg)
Instalación y ensamblaje: Soporte Articulador Peerless
Ultra-Thin Para Pantallas Planas de 32" a 46"*
Modelo: SUA737

Español
9 de 23 PUBLICADO: 12-15-11 HOJA #: 095-9371-2 03-08-12
Contenido
Lista de piezas..................................................................................................................................................................... 10
Instalación en una pared................................................................................................................................................11, 12
Instalación de los soportes adaptadores............................................................................................................................. 13
Instalación y desinstalación de la pantalla plana ................................................................................................................ 14
Herramientas necesarias para el ensamblaje
• localizador de montantes (se recomienda uno de "borde a borde")
• destornillador phillips
• taladro
• broca de 5/16" (8mm) para paredes de concreto y de bloque de hormigón de escorias
• broca de 5/32" (4mm) para paredes con montantes de madera
• nivel
NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las
advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente
internacional, por favor, comuníquese con su distribuidor local.
• Este soporte está diseñado para sostener la pantalla a 1.29" de la pared. Por favor, repase las recomendaciones del
manual de instalación del fabricante con respecto a la distancia necesaria de la pared para evitar el riesgo de sufrir
lesiones o causar daños a la propiedad.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga
experiencia en construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los
fijadores y componentes.
• Nunca sobrepase la capacidad máxima de soportar carga para Underwriters Laboratories. Vea la página 8.
• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén
anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
con más seguridad.
• Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede
disminuir significativamente su fuerza de fijación.
• Este producto está diseñado para uso en interiores solamente. Utilizar este producto en exteriores podría causar
fallas del producto y lesiones a individuos.
• Este producto fue diseñado para ser instalado en paredes con la siguiente construcción solamente:
CONSTRUCCIÓN DE LA PARED ACCESORIOS NECESARIOS
• Montante de madera Incluido
•Viga de madera Incluido
•Concreto macizo Incluido
•Bloque de hormigón de escorias Incluido
•Ladrillo Comuníquese con un profesional calificado (no evaluados por UL)
•¿Otra superficie o no está seguro? Comuníquese con un profesional calificado
ADVERTENCIA

Español
10 de 23 PUBLICADO: 12-15-11 HOJA #: 095-9371-2 03-08-12
Algunas partes pueden diferir un poco de las ilustradas.
Antes de comenzar, asegúrese de que su producto incluye todas las piezas ilustradas.
A
Descripción Cant. Nº de pieza
A
armazón del brazo de pared 1 046-P1260
Ctornillo para madera 2 520-1202
Danclaje para concreto 2 590-0320
Etornillo M4 x 6mm 2520-1006
Fllave de se
g
uridad 1560-1133
Lista de piezas
F
llave de seguridad
1
560 1133
Gllave allen de 4mm 1560-9646
Hcubierta para sujetadores 2 590-1324
Ianclaje para cables 1 046-P1134
Jclip para cables 1 046-P1138
K
sujetacables 2 046-0136
Ltornillo M5 x 12mm 4 560-1732
Mtornillo M5 x 25mm 4 560-1733
Ntornillo M6 x 12mm 4 560-1734
Otornillo M6 x 25mm 4 560-1735
Ptornillo M8 x 12mm 4 560-1736
Qtornillo M8 x 25mm 4 560-1737
Respaciador 3/4" 4 540-1059
Sarandela 4 540-9478
G
CDE F
HI
J
K
LMN O P Q R S