peerless-AV SA752PU Guide

Models: SA752PU / PEWS350/BK
Installation and Assembly:
Universal Articulating Arm Wall Mount for 32" to 52" Flat Panel
Displays
ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity: 90 lb (41.82 kg)

2 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.............................................................................................................................................................................3, 4
Wall installation...................................................................................................................................................................5, 6
Installing Adapter Brackets to Display ...............................................................................................................................7-11
Mounting Flat Panel Display.................................................................................................................................................12
Cable Management ..............................................................................................................................................................14
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• 5/32" (4mm) drill bit for wood studs
• 5/16" (8mm) drill bit for concrete and cinder block
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Metal Stud Contact Qualified Professional (not evaluated by UL)
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional
WARNING

3 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
B
CDE FG
H
JK
IM
A
SA752PU
Description Qty. Part #
Awall arm assembly 1 095-P1715
Buniversal adapter bracket 1 095-P1635-2
Cwood screws 3 520-1202
Dconcrete anchors 3 590-0320
EM10 x 15 mm socket head screw 2520-9262
Ffastener caps 3590-1324
Gcable ties 8590-1168
H6 mm allen wrench 1 560-9716
I5 mm allen wrench 1 560-9640
Jrear cable cover 2 590-P1326
Kfront cable cover 2 590-P1327
L#3 screwdriver bit (not shown) 1 560-0209
M5/32 allen wrench 1 560-9646
Parts List
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.

4 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Adapter Bracket Fasteners
M4 x 12mm (6)
(504-9013)
M4 x 25mm (4)
(504-1015)
M5 x 12mm (4)
(520-1027) M5 x 25mm (4)
(520-9543)
M8 x 16mm (6)
(520-9257)
M8 x 40mm (4)
(520-1136)
M8 x 25mm (4)
(520-1031)
I.D. .34" (4)
(540-1059)
I.D. .22" (4)
(540-1057)
M6 x 30mm (4)
(510-9109)
M6 x 12mm (4)
(520-1128) M6 x 25mm (4)
(520-1208)
M6 x 20mm (4)
(520-9402)
multi-washer (6)
(580-1036)

5 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Using a stud finder, locate and mark the edges of the wood stud. Use a level to draw a vertical line down the center
of the stud and mark the desired display center. Use wall plate template (wall arm) to mark center of holes along
the vertical line. The top mounting hole should be 7.54" (192mm) above the desired display center as shown in
figure 1.1. Drill three 5/32" (4mm) dia. holes to a depth of 2.5" (64mm). Attach wall arm (A) to wall with three wood
screws (C) using #3 phillips screwdriver bit (L) as shown in fig. 1.2. Level then tighten all fasteners.
Insert three fastener caps (F) into wall plate mounting holes.
Installation to Single Wood Stud Wall
1
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING
7.54"
(192mm)
CS = CENTER OF DISPLAY
WOOD STUD
C
F
A
WOOD STUD
WALL PLATE
CS
fig. 1.1
fig. 1.2

6 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Installation to Solid Concrete or Cinder Block
Mark the desired display center and use wall plate
template (wall plate) to mark mounting holes.The top
mounting hole should be 7.54" (192mm) above the
desired display center as shown in figure 1.1 on page
5. Drill three 5/16" (8mm) dia. holes 2.5" (64mm) deep
as shown in fig. 1.3. Insert anchors (D) into holes flush
with wall. Place wall arm (A) over anchors and secure
with three wood screws (C) using #3 screwdriver bit
(L). Level then tighten all fasteners.
Insert three fastener caps (F) into wall plate mounting
holes.
D
1
A
fig. 1.3
C
F
1
3
2
D
Drill holes and insert anchors (D).
Place wall arm (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
A
D
C
concrete
surface
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable (not
evaluated by UL), the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16mm), custom fasteners must be supplied by
installer (not evaluated by UL).
WARNING
SOLID CONCRETE
CINDER BLOCK
WALL PLATE

7 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
NOTE: If display has a VESA 400 horizontal
mounting pattern, skip to step 2-3 or 2-4 on page 9.
NOTE: For VESA 200x200 or VESA 200x100
mount hole patterns, skip to step 3 on page 10.
NOTE: For dedicated PLP plate installation skip to
step 4 on page 12.
Remove four 1/4-20 x .6" screws using 5mm allen
wrench (I) and loosen two 1/4-20 x 1.25" screws
1/2 turn to allow for display bracket adjustment.
1/4-20 x .6" SCREWS
1/4-20 x 1.25" SCREWS
2
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down and refer to display manufacturers instructions for removing obstructions from the
back of the display. Adjust display brackets to align with display mounting holes.
Measure horizontal mounting hole pattern and choose fixed stop-position from chart below.
2-1
FIXED STOP-POSTION #2
FIXED STOP-POSTION #1
FIXED STOP-POSTION #3
horizontal mounting hole pattern fixed stop-position
10-3/4" - 16-1/16" (273 - 408 mm) #1
15-1/16" - 21-9/16" (383 - 548 mm) #2
20-7/16" - 27-9/16" (519 - 700 mm) #3
Installing Adapter Brackets to Display

8 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Select the screws from the baffled fastener pack that best fit your display and secure to display following step 2-3
or 2-4 on page 9.
NOTE: Top and bottom mounting holes must be used for attaching display brackets. Middle holes should also be
used where the fasteners and displays allow.
Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.
CENTER DISPLAY BRACKETS VERTICALLY AND
HORIZONTALLY ON BACK OF DISPLAY
DISPLAY
DISPLAY BRACKETS
NOTE: "X" dimensions should be equal.
"Y" dimensions should be equal.
• Tighten screws so display brackets are firmly attached to display. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing
screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
YY
X
X
2-2
Installing Adapter Brackets to Display

9 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Begin with the shortest length screw, hand thread
screw through multi-washer and display brackets
(B) into display as shown below. Screw must make
at least three full turns into the mounting hole and
fit snug into place. Do not over tighten. If screw
cannot make three full turns into the display, select
a longer length screw from the baffled fastener
pack. Repeat for remaining mounting holes, level
display brackets and tighten screws.
NOTE: Spacers may not be used, depending upon
the type of display.
Skip to step 2-5.
Begin with the longest length screw, hand thread
screw through multi-washer, display brackets (B)
and spacer in that order into display as shown
below. Screw must make at least three full turns
into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three
full turns into the display, select a shorter length
screw from the baffled fastener pack. Repeat for
remaining mounting holes, level display brackets
and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
2-3
2-4
DISPLAY
MULTI-WASHER
SCREW
B
DISPLAY
MULTI-WASHER
SPACER
B
SCREW
Center display brackets horizontally and vertically
on back of display. Tighten two 1/4-20 x 1.25"
screws. Reinstall four 1/4-20 x .6" screws using
5mm allen wrench (I) into appropriate fixed-stop
position from chart on page 7.
2-5 1/4-20 x 1.25" SCREWS
1/4-20 x .6" SCREWS

10 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-7 07-11-11
Remove four 1/4-20 self tapping screws to detach display brackets from outer mount holes of universal adapter
bracket (B) using 5mm allen wrench (I) as shown in figure 3.1. Reinstall four 1/4-20 self tapping screws to secure
display brackets to inner set of mounting holes on universal adapter bracket (B) as shown in figure 3.2.
1/4-20 SELF
TAPPING SCREWS 1/4-20 SELF
TAPPING SCREWS
Display
BRACKETS Display
BRACKETS
INNER
MOUNTING
HOLES
OUTER
MOUNTING
HOLES
fig. 3.1 fig. 3.2
VESA 200 x 200 or VESA 200 x 100 Mounting Pattern
To prevent scratching the display, set a cloth on a
flat, level surface that will support the weight of the
display. Place display face side down and place
universal adapter bracket (B) onto display.
3-1
3
BB
B
1/4-20 x .6" SCREWS
1/4-20 x 1.25" SCREWS
Remove four 1/4-20 x .6" screws using 5mm allen wrench
(I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to allow for
display bracket adjustment.