PEERLESS Mounts Smartmount D-FPF-220 Guide

ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
Features:
•Screen held only 1.25" (32 mm) from wall for ultra-slim application
•Open wall plate design allows for additional wall access, increasing electrical access and cable management options
•Universal screen mounting brackets hook onto the wall plate for quick, easy, and safe installation
• 
•Includes Sorted-For-You™ fastener pack for installation to wood studs, concrete and cinder block
• 
•Available in black and silver
Models: D-FPF-220, D-FPF-220S, RTFPF-220,
RTFPF-220S, SWS211/BK, SWS211/SI
*

Installation and Assembly:
Smartmount®Universal Flat Wall Mount for
23" - 46" (58 - 117 cm)* LCD Flat Panel Screens

©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2

2 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
.................................................................................................................................................................................3
Installation to Double Wood Stud Wall ...................................................................................................................................
 ........................................................................................................................5
Installing Adapter Brackets.....................................................................................................................................................
Mounting and Removing Flat Panel Screen...........................................................................................................................
Tools Needed for Assembly
• 
• phillips screwdriver
•drill
 
 
• level
 
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

your local distributor.
 
construction, and fully understands these instructions.
 
hardware and components.
 
 

 
 
power.
 
injury.
 
WALL CONSTRUCTION HARDWARE REQUIRED
 •Wood Stud Included
•Wood Beam Included
•   
•   
•   
•    
•   
WARNING

3 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
CC DDAA BB
Adapter Bracket Fasteners











(520-1027)





 
(510-9109)
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
D-FPF-220
RTFPF-220
SWS211/BK
D-FPF-220S
RTFPF-220S
SWS211/SI
Description Qty. SF640 SF640-S SF640P SF640P-S
AA wall plate 1    
BB adapter bracket 2    
CC      
DD   590-0320 590-0320 590-0320 590-0320
EE      
Parts List
EE

4 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
Installation to Double Wood Stud Wall

Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The



CC
Skip to step 2.
g.1.1

AA
STUD
CC
AA
g.1.2


(103 mm)
 
attached hardware and components.
 
screws, greatly reducing their holding power.
 
 
highly recommended.
 

WARNING
1

5 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
Installation to Solid Concrete or Cinder Block
Make sure that wall plate (AA) is level, use it as a
template to mark four mounting holes. The top mounting



DD
wall as shown (right). Place wall plate over anchors and
CC
all fasteners.
CC
AA
DD


1
3
2
DD
Drill holes and insert anchors (DD).
Place plate (AA) over anchors (DD) and secure with screws (CC).
Tighten all fasteners.
AA
DD
CC
concrete
surface
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
 
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount


hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
 
 
and components.
WARNING
1
 
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
 
 directly
to load-be aring concrete.
 
concrete covered with plaster, drywall, or other



shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws.

custom fasteners must be supplied by installer (not

WARNING

6 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
InstallingAdapterBrackets

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown below.
Attach the adapter brackets to the back of the screen using the appropriate combination of screws, washers, and

NOTE: Top and bottom holes must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
NOTE: For atbackscreens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.
BB


X
X
NOTE: "X" dimensions should be equal.
 
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. 
 
secured, damage may occur to screen or product may fail.
WARNING
2

7 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
www.peerlessmounts.com/1
for a full screen compatibility chart for this mount.
Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown


Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
www.peerlessmounts.com/1
for a full screen compatibility chart for this mount.
Begin with longer length screw, hand thread through washer, adapter bracket and spacer in that order into screen


fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Screen
For Bump-out or Recessed Back Screen
BB)

g2.1
WASHER

2-2
2-1
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.

WASHER

BB)
g2.2


8 of 34 ISSUED: 09-07-07 SHEET #: 202-9223-2 05-07-09
MountingandRemovingFlatPanelScreen
Hook adapter brackets (BB) onto wall plate (AA).
Then slowly swing screen in as shown. Turn safety/
security screws, using security allen wrench (EE),
clockwise at least six times to prevent screen from

Screen can be adjusted horizontally if desired as

NOTE: To lock the screen down, tighten safety/
security screws to wall plate as shown in cross
section.
To remove screen from mount, loosen safety/
security screws, swing screen away from mount,
and lift screen off of mount.
3
 
WARNING
BB
 
Overtightening can cause damage to mount. Tighten

CAUTION
g3.1
g3.2
BB
SAFETY/


AA
CROSS SECTION
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.


www.peerlessmounts.com


Características:


manejo de cables



 


la pantalla

Modelos: D-FPF-220, D-FPF-220S, 
RTFPF-220, RTFPF-220S, SWS211/BK, SWS211/SI



Instalación y ensamblaje:
Soporte universal de pared plano SmartMount® para
pantallas planas LCD de 23" a 46" (58 - 117 cm)*

©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2

10 de 34 
Español
Contenido
......................................................................................................................................................................11
............................................................................................... 12
....................................................... 13
............................................................................................................................. 
......................................................................................................... 
Herramientas necesarias para el ensamblaje
•localizador de montantes (se recomienda uno de "borde a borde")
• destornillador phillips
• taladro
• 
• 
• nivel
Nota:
 



 

 

  
 
anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".
 

 

 
fallas del producto y lesiones a individuos.
 
CONSTRUCCIÓN DE LA PARED ACCESORIOS NECESARIOS
 •Montante de madera Incluido
•Viga de madera Incluido
•    
•  
•   
      
•     
• 
ADVERTENCIA