PEERLESS Mounts SmartMount ST670 Guide

ISSUED: 03-25-09 SHEET #: 202-9334-1
Installation and Assembly:
SmartMount®Universal Tilt Wall Mount for LCD and Plasma
Flat Panel Screens
Features:
• Screen held only 3" (76 mm) from wall for a discreet installation
• Wall plate design allows for wall acces allowing multiple cable management options
• Universal tilt brackets easily hook onto wall plate for fast installation
• Adjustable up to 15° of forward tilt and up to -5° backward tilt for optimal viewing angle
• One-touch tilt for effortless adjustment
• Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy motion.
• Easy grip handle locks the screen position into place
• Optional IncreLok feature offers fixed tilts at -5°, 0°, 5°, 10° and 15° increments
• Includes Sorted-For-You™ fastener pack for installation to wood studs, concrete, and cinder block
• Optional horizontal adjustment of up to 8" (203 mm) (depending on screen model) for perfect
screen placement
• Available in Black or Silver
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
Model # Screen Size Range Max. Load Capacity
ST670, ST670P, ST670-S, ST670P-S,
SWS520/BK, SWS520/SI 42''- 71'' (107 - 180 cm) 250 lb (113 kg)
ST680, ST680P, ST680-S, ST680P-S 61''- 102'' (155 - 259 cm) 350 lb (159 kg)

2 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Triple Wood Stud Wall......................................................................................................................................5
Installation to Solid Concrete or Cinder Block ........................................................................................................................6
Installing Tilt Brackets.............................................................................................................................................................7
Installing Flat Panel Screen to Wall Plate...............................................................................................................................9
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - ACC615;
• Brick Contact Qualified Professional
• Other or unsure? Contact Qualified Professional
WARNING
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
•drill
• 5/16" (8 mm) bit for concrete and cinder block wall
• 5/32" (4 mm) bit for wood stud wall
• level

3 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
CC
AA
BB
DD
FF
EE
Parts may appear slightly different than illustrated.
Before you begin, be sure all parts shown are included with your product.
Adapter Bracket Fasteners
M4 x 12 mm (4)
(504-9013)
M6 x 25 mm (4)
(520-1208)
M4 x 25 mm (4)
(504-1015)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M5 x 12 mm (4)
(520-1027)
.5" spacer (4)
(540-1057)
.75" spacer (4)
(540-1059)
M8 x 16 mm (6)
(520-9257)
M8 x 40 mm (4)
(520-1136)
multi-washer (4)
(580-1036)
M8 x 25 mm (4)
(520-1031)
M6 x 20 mm (4)
(520-9402) M6 x 30 mm (4)
(510-9109)
Parts List
Description Qty.
ST680
ST670
ST680-S
ST670-S
SWS520/BK
ST680P
ST670P
SWS520/SI
ST680P-S
ST670P-S
XX AAwall plate 1 200-1901 200-4901 200-1901 200-4901
XX 200-1902 200-4902 200-1902 200-4902
XX BBleft tilt bracket 1 201-1474 201-4474 201-1473 201-4473
XX 201-1480 201-4480 201-1477 201-4477
XX CCright tilt bracket 1 201-1476 201-4476 201-1475 201-4475
XX 201-1478 201-4478 201-1479 201-4479
XXXXDD#14 x 63.5 mm wood screw 6 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
XXXXEEconcrete anchor 6 590-0320 590-0320 590-0320 590-0320
XXFF4 mm allen wrench 1 560-1146 560-1146 - -
ST670P, ST670P-S, SWS520/BK, SWS520/SI ST680P, ST680P-S ST670, ST670-S ST680, ST680-S

4 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
M4 x 12 mm (6)
(510-1079) M5 x 12 mm (4)
(520-1064)
M5 x 25 mm (4)
(520-1122)
M6 x 25 mm (4)
(520-1211)
M4 x 25 mm (4)
(510-1082)
M6 x 12 mm (4)
(520-1050) M8 x 15 mm (6)
(520-1068)
M8 x 40 mm (4)
(520-1152)
I.D. .34" (8.6 mm) (4)
(540-1059)
I.D. .22" (5.6 mm) (4)
(540-1057)
multi-washer (6)
(580-1036)
M6 x 20 mm (4)
(520-9554)
M6 x 30 mm (4)
(520-1067)
M8 x 25 mm (4)
(520-1101)
Security Adapter Bracket Fasteners

5 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
Installation to Triple Wood Stud Wall
Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each
stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" (64 mm) above the
desired screen center as shown in figure 1.1. Level plate, and mark the center of the six mounting holes. Make sure
that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure
that the wall plate is level, secure it using six #14 x 63.5 mm wood screws (DD) as shown in figure 1.2.
Skip to step 2.
NOTE: Wall plate may be mounted up to 6" (152 mm) off center as shown in figure 1.1.
DD
AA
fig. 1.2
1
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations (not UL approved).
WARNING
CS = center of screen fig. 1.1
STUD
AA
6"
(152 mm)
2.5"
(64 mm)
6"
(152 mm)
CS

6 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
Installation to Solid Concrete or Cinder Block
Make sure that wall plate (AA) is level, use it as
a template to mark four mounting holes. The top
mounting hole should be 2.5" (64 mm) below the
desired screen center as shown in figure 1.1 on page
5. Drill four 5/16" (8 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Insert anchors (EE) in holes
flush with wall as shown (right). Place wall plate over
anchors and secure with #14 x 63.5 mm screws (DD).
Level, then tighten all fasteners.
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable,
the finishing surface must be counterbored as
shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16 mm), custom
fasteners must be supplied by installer.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
EE
Drill holes and insert anchors (EE).
Place plate (AA) over anchors (EE) and secure with screws (DD).
Tighten all fasteners.
AA
EE
DD
concrete
surface
DD
AA EE
SOLID CONCRETE
CINDER BLOCK

7 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
Attaching Tilt Brackets to Screen using Baffled Fastener Pack
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs,
base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the
adapter brackets to be attached. Select the small, medium, large or extra large screws from the baffled fastener
pack then attach tilt brackets to screen following figure 2.1 or 2.2.
NOTE: Be sure to attach tilt brackets with handle facing outward as shown below.
NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used
where the fasteners and screens allow. Verify that all holes are properly aligned, and then tighten screws using a
phillips screwdriver.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening
can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to
become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
BB
CENTER BRACKETS VERTICALLY
ON BACK OF SCREEN
X
CC
X
HANDLE FACE
OUT
Note: "X" dimensions should be equal.
NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.
2
MULTI-WASHER
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
Notes:
• The number of fasteners used will vary,
depending upon the type of screen.
• Multi-washers and spacers may not be used,
depending upon the type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
• Slots in ST680 models are wider and require
the use of the M8 washer.

8 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3
for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this
mount.
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.
If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.
Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3
for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this
mount.
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the
baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.
For Flat Back Screen
For Bump-out or Recessed Back Screen
ADAPTER
BRACKET
(BB or CC)
SCREEN
fig. 2.1
SCREW
2-1
2-2
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
MULTI-WASHER
SCREEN
SCREW
ADAPTER
BRACKET
(BB or CC)
fig. 2.2
SPACER
MULTI-WASHER

9 of 18 ISSUED: 03-25-09 SHEET #: 202-9334-1
For preset tilt angles use Increlok™ and for custom
tilt angle use ratchet handle.
INCRELOK™: The screen can be locked into a
pre-set tilt position of -5°, 0°, 5°, 10° or 15°. Use
locator hole to find tilt position hole and tilt screen
to align holes. Tighten IncreLok™ tilt locking
screws on both tilt brackets to lock tilt as shown in
detail 2.
Ratchet Handle: Loosen ratchet handle (refer to
step 3 for tension adjustment of handle). Push or
pull from top or bottom of screen to adjust tilt as
shown in figure 4.1. The tilt can be adjusted to a
maximum of 15° forward or 5° backward.
Tension Adjustment of Ratchet Handle: Adjust
tension in tilt brackets (BB & CC) by rotating ratchet
handle. NOTE: If obstruction prevents ratchet handle
from rotating, pull handle out while turning will allow
handle to reposition without tightening. Release and
turn handle to tighten or loosen.
Mounting Screen: Ratchet handle must be in the
up or down position or interference will occur while
hooking tilt brackets to wall plate (AA). Slowly hook tilt
brackets (BB & CC) onto wall plate (AA) and swing
screen down as shown in fig. 3.1. Tilt bracket hooks
must fully engage wall plate as shown in detail 1. Using
phillips screw driver/allen wrench (FF), turn safety
screws on tilt brackets (BB & CC) clockwise till screw
tip securely contacts wall plate as shown in cross
section.
Screen Adjustment: Screen can be adjusted
horizontally by loosening safety/security screws on
tilt brackets (BB & CC) three full turns. Adjust screen
as shown in figure 3.2. Tighten safety screws on tilt
brackets till screw tip securely contacts wall plate as
shown in cross section.
Removing Screen: To remove screen from mount,
loosen safety screws, swing screen away from mount,
and lift screen off of mount.
Mounting and Removing Flat Panel Screen
DETAIL 2
fig. 4.1
IncreLok™
TILT LOCKING
SCREW LOCATOR
HOLE
RATCHET
HANDLE
TILT
POSITION
HOLES
fig. 3.2
Adjusting the Tilt Angle of the Flat Panel
Screen
• Always use an assistant or mechanical lifting equipment
to safely lift and position the flat panel screen.
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
• Be careful not to pinch fingers when pushing screen from
the bottom.
WARNING
fig. 3.1
RATCHET
HANDLE
AA
SAFETY/
SECURITY
SCREW
DETAIL 1
BB &
CC
AA
CROSS SECTION
BB &
CC
3
4
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com

Anbringung und Zusammenbau:
SmartMount®-Universal-Wandkipphalter für LCD- und Plasma-
Flachbildschirme
Merkmale:
• Angebrachter Bildschirm steht nur 76 mm (3 Zoll) von der Wand ab und fügt sich so unauffällig in den Raum
• Wandplattendesign ermöglicht Zugang zur Wand und bietet damit vielfältige Kabelführungsoptionen
• Schnelle Anbringung durch einfaches Einhaken der Universal-Kipphalterungen in die Wandplatte
• Optimaler Betrachtungswinkel durch Neigbarkeit bis 15° nach vorne und -5° nach hinten
• Mühelose Neigungseinstellung durch einmaliges Antippen
• Vorspannung der Universalkipphalterung ermöglicht Neigungswinkeleinstellung mit einer einfachen Bewegung
• Arretieren der Bildschirmstellung über leicht zugänglichen Griff
• Optionale IncreLok-Funktion bietet fixe Neigungsstellungen bei -5°, 0°, 5°, 10° und 15°
• Einschließlich Sorted-For-You™-Befestigungsteilesortiment zur Anbringung an Holzständern, Beton und Porenbetonstein
• Optionale horizontale Verstellung bis zu 203 mm (8 Zoll) (abhängig vom Bildschirmmodell) ermöglicht optimale Platzierung des Bildschirms
• In Schwarz oder Silber verfügbar
HINWEIS: Lesen Sie bitte das gesamte Anleitungsblatt durch, bevor Sie mit Anbringung und Zusammenbau beginnen.
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
Modell-Nr. Bildschirmgröße Max. Tragfähigkeit gem. UL-Zulassung
ST670, ST670P, ST670-S, ST670P-S,
SWS520/BK, SWS520/SI 42''- 71'' (107 - 180 cm) 250 lb (113 kg)
ST680, ST680P, ST680-S, ST680P-S 61''- 102'' (155 - 259 cm) 350 lb (159 kg)
AUSGEGEBEN: 03-25-09 BLATT NR.: 2029334-1