Pegler Yorkshire Performa User manual

Wall Mounted Infrared
Wall Mounted Infrared
Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode Price (£) each ex VAT
General Information
Wall Mounted Infrared
Code Description Dimensions
343054 Wall Mounted Infrared- Battery See image
Pegler Yorkshire reserve the right to change specifications
Dimensions
5 Year Guarantee
Luxury Taps and Mixers
Pegler Customcare 5 Year Guarantee - Terms and Conditions
Product are subject to a 5 year guarantee that is between Pegler and the final purchaser of the product.
The guarantee is subject to proof of purchase being supplied.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear
and tear.
Finishes other than chrome are covered for a period of 3 years only and the guarantee on the finish is
subject to the cleaning instructions being followed.
The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting
instructions.
Abusive behaviour and accidental damage to the product are not covered by this guarantee.
The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Guarantee
Description Minimum Operating
Pressure (bar)
Maximum Cold
Working
Pressure (bar)
Maximum Hot
Working Pressure
(bar)
Wall Mounted
Infrared 0.2 Bar 6 Bar 6 Bar
Pressure and Temperature

Care
To maintain the surface finish, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry,
using a soft cloth. Never use abrasive cleaners or chemical household cleaners and avoid contact with
concentrated bleach.
Maintenance
No regular maintenance is required for this product.
In case of complete replacement Pegler recommend service valves should be fitted to the supply inlets.
For any further help or replacement parts please contact the Service Support Team on 0800 1560050.
Care and Maintenance
Wall Mounted Infrared
1
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
1SEN2 SENSOR 854423 5013866080432 01/01/1900 06/09/2018 £0.00
2
Spare
Key Description Code Barcode Date From Date To Price (£) ex VAT
2ON11 OUTLET NIPPLE INFRA
RED 854426 5013866080463 01/01/1900 06/09/2018 £0.00
3
Spare
Key Description Code Barcode Date From Date To Price (£) ex VAT
3FS10CP FLOW STRAIGHTNER ASSEMBLY
CHROME 812400 5013866056161 01/01/1900 To Current
£0.00
4
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
41/2 BN 915L BACKNUT 817074 5013866023385 01/01/1900 06/09/2018 £0.00
5
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
5OR7 O RING 817063 5013866072154 01/01/1900 06/09/2018 £0.00
6
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
6C4 CONNECTOR PUSH FIT 854427 5013866080470 01/01/1900 06/09/2018 £0.00
7
Spare
Key Description Code Barcode Date From Date To Price (£) ex VAT
7CM3 CONTROL MODULE BOX
BATTERY 854399 5013866079924 01/01/1900 06/09/2018 £0.00
8
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
8Solenoid Valve With Filter 858083 01/01/1900 To Current £0.00
9
Spare Key Description Code Barcode Date From Date To Price (£) ex VAT
9EW1 ELECTRICAL WIRE 854424 5013866080449 01/01/1900 06/09/2018 £0.00
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone [phone] Fax: [phone] Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507

1
INSTALLATION OPERATION CARE
343054 - BATTERY
343055 - MAINS
343052 - BATTERY
343053 - MAINS
343051 - BATTERY 343050 - BATTERY
OBSERVE ELECTRONIC SENSOR TAPS
Optical Sensor Tap - Deck Mount
Capacitive Sensor Tap - Wall Mount
Optical Sensor Tap - Wall Mount
Capacitive Sensor Tap - Deck Mount

1
AQUA
STOP
WHAT YOU SHOULD HAVE IN YOUR PACKAGE
RECOMMENDED TOOLS
X2
X2
X2
A
B C
DE F G
H I J K
LM N O
ONLY FOR
ITEMS M & N
OR
OR OR
OR OR
OR OR
ALL
ALL
ALLCAPACITIVE SENSOR TAPS ONLY - 343051 & 343050
343052
343053 343050
343054
343055
343051
343050
343052
343053 343051
343054
343055
343054
343055
343052
343053
343051
343050
343053
343055
343054
343052
343050
343051
TAP BODY
CLAMPING RODS BACK PLATE
INLET HOSE CLAMPING
NUTS
MOUNT
BRACKET
FIBRE
WASHER
CONDUCTIVE
RING
BRASS
WASHER
SHORT
NUT
SOLENOID
VALVE WITH
FILTER
MAINS POWER BOX BATTERY BOX BATTERY &
CONTROL BOX
BATTERY
10mm BOX
SPANNER

2
1. IMPORTANT
Read this manual before installation
&DUHPXVWEHWDNHQGXULQJLQVWDOODWLRQWRSUHYHQWDQ\ULVNRIGDPDJHWRWKHSURGXFWRULQMXU\WRLQVWDOOHU,QVWDOODWLRQPXVWEHFDUULHGRXWE\DTXDOL¿HGDQGFRPSHWHQWSHUVRQDQGLQDFFRUGDQFHZLWKWKHLQVWUXFWLRQVVXSSOLHG(QVXUHZDWHUVXSSO\FRPSOLHVZLWKWKHZDWHUUHJXODWLRQV,QVWDOODWLRQVPXVWFRPSO\ZLWKDOOORFDODQGQDWLRQDOUHJXODWLRQV$OOHOHFWULFDOLQVWDOODWLRQVPXVWFRPSO\ZLWK,(7UHJXODWLRQVDQGFDUULHGRXWE\DVXLWDEOHTXDOL¿HGLQVWDOOHU2. INTRODUCTION
Performa Electronic Sensor Taps are available with two types of Sensing Technology:
1. Optical Sensor taps use infrared light to
detect a user’s hands in the area beneath
the spout. When a detection is made in the
solenoid valve is operate for a pre-set period
to provide water at the outlet. &DSDFLWLYH6HQVRUWDSVKDYHD¿HOGaround the whole tap body that can detect a
XVHU¶VKDQGV,QWHUUXSWLQJWKLV¿HOGWULJJHUVthe solenoid valve and water is provided at
the outlet.
7RUHGXFHZDWHUFRQVXPSWLRQERWKUDQJHVDUHIDFWRU\¿WWHGZLWKD/PLQÀRZUHJXODWRUDQGtimer. Neither sensor taps require physical contact to operate.
3. PREPARATION
Take extra care to ensure the electrical connections are correct, securely connected and
where applicable the relevant seals and glands are used to protect the electronics.
0DNHVXUHDOOHOHFWURQLFSDUWVDUH¿WWHGLQDGU\DUHDEHKLQGWKHZDOORUEHQHDWKWKHVLQNbasin.
Do not solder near the solenoid valve, excessive heat will damage the valve and its
connections.
5RXWHVXSSO\SLSHZRUNWRWKHSRLQWZKHUHWKHVROHQRLGYDOYHZLOOEH¿WWHGWKHQÀXVKpipework thoroughly before installing the solenoid valve.
WALL WALL WALL
DECK DECK DECK
Mininum Height
180mm
From Basin
1. Remove old tap 2. Drill hole
'5,//+2/(PP3. Thoroughly clean mounting
area

4. INSTALLING THE TAP
A
B
C
D
Screw clamping rods (B) into tap
(A).
Make sure rods are fully secure
and aligned.
Fit back plate (C) over rods.
Ensure Performa marking is facing
towards the spout outlet.
Screw the inlet hose (D) into
remaining hole.
Screw in fully to seal. +DQGWLJKWRQO\WRDYRLGKRVHWZLVWLQJ.
1.
2.


4
E
H
I
J
G
F
WALL / SINK
WORKTOP
SHOULD LOOK
LIKE THIS...
Fit rods and inlet hose through the
KROHLQWKHZDOOZRUNWRSVLQN6OLGHWKH¿EUHZDVKHU*RYHUWKHhose and rods.
Fit bracket (F), ensuring the
notches align with the rods.
Use long clamping nuts (E) to
FODPSWKHEUDFNHW¿EUHZDVKHUDQGtap together.
Tighten using either a box spanner
or adjustable spanner. Ensure the
tap is completely secure.
&DSDFLWLYHVHQVRUWDSVRQO\.
Sandwich the conductive ring (H)
with two brass washers (I). Secure
it using the short nut (J). This can
be mounted on either rod. Ensure
the tab (circled) on ring (H) is
accessible.
4.
5.
6.

5
5. INSTALLING WATER CONNECTION
$'9,&($OOSLSHZRUN0867%(WKRURXJKO\ÀXVKHGSULRUWRLQVWDOODWLRQWRSUHYHQWEORFNDJHRUSHUPDQHQWdamage to the solenoid valve.
$VHUYLFHYDOYHVKRXOGEH¿WWHGXSVWUHDPRIWKHVROHQRLGYDOYHWRDOORZWKHWDSWREHLVRODWHGIRUmaintenance.
,WLVUHFRPPHQGHGWKDWD7KHUPRVWDWLFPL[LQJYDOYH709LV¿WWHG>VXFKDVWKH3HJOHU3(*$@7KLVZLOOOLPLWWKHPD[LPXPWHPSHUDWXUHRIWKHZDWHUDWWKHWDSWRVDIHZDVKLQJWHPSHUDWXUHVSUHYHQWLQJVFDOGV&LVWKHPD[LPXPUHFRPPHQGHGVDIHZDVKEDVLQWHPSHUDWXUHIf the supply pressure is greater than 5 bar, it is recommended that a pressure reducing valve is
¿WWHGWRUHGXFHLWWREDU
PERFORMA TAP
62/(12,'9$/9(:,7+*´CONNECTIONS
6833/<6((%(/2:)25RECOMMENDED
UPSTREAM
9$/9(6DO NOT REMOVE! 7(50,1$/6CAN ROTATE
)25($6<ACCESS
$/:$<632,17,1*IN THE DIRECTION
2))/2:
),/7(56($/,1BETWEEN
CONNECTIONS

6
6. INSTALLING ELECTRICAL CONNECTION
D0$,166833/<237,&$/6(16251. Site the mains power supply box close to the inlet to the tap and solenoid valve. Use the length of
the sensor cables for guidance.
2. Remove glands and nut.
3. Secure the box to the wall. To avoid cables contacting water, mount the Mains Power supply box
ZLWKLWVJODQGVIDFLQJWRZDUGVWKHÀRRUPlace gland nuts and glands on cables and pass cables through glands into the mains power
supply box.
5. Wire the mains connector observing polarity. Note that the mains supply connection terminal
GLVSOD\VDV³/1´LQJUHHQVORWFDQEHUHPRYHGIRUHDVLHUZLULQJConnect the Eye sensor cables to the power supply unit and solenoid valve as shown above.
7. 7LJKWHQWKHVWXI¿QJJODQGVDQGQXWVDQGWKHQVHFXUHWKHOLGXVLQJWKHVXSSOLHGVFUHZVWRVHDOWKHmains supply box.
SWITCH
MUST BE
219MAINS
6833/<,1387RED
&$%/(%/$&.&$%/(*5(<&$%/(&$%/(*/$1'187$//6&5(:63$&.0867BE USED TO SECURE THE
&21752/02'8/(/,'(<(6(1625,6PRE-FITTED IN
7$3%$&.3/$7(6(1625(<(CONNECTION
0$,166833/<&211(&7,217(50,1$/IT IS RECOMMENDED THAT
($&+32:(56833/<%2;,6CONNECTED TO THE MAINS
%<$)86('6:,7&+6385RATED AT 3 AMPS. ENSURE
7+,66833/<,6,62/$7('%()25(67$57,1*72,167$//7+(0$,166833/<%2;6((6(&7,213$*()25)857+(5'(7$,/6

7
E%$77(5<237,&$/6(16251. Site the battery box close to the inlet to the tap and solenoid valve. Use the length of the sensor
cables for guidance.
2. Secure the box to the wall or support. Where possible position the battery box away from water
ZLWKWKHFDEOHRXWOHWIDFLQJWRZDUGVWKHÀRRU3. Remove the box lid from the control module.
Connect the sensor to the power supply unit and solenoid valve as shown above.
%/$&.&$%/(*5(<&$%/(RED
&$%/(%/$&.&$%/(*5(<&$%/(&$%/(287/(7

8
F%$77(5<&$3$&,7,9(6(16251. Site the battery box close to the inlet to the tap and solenoid valve. Use the length of the sensor
cables for guidance.
2. Secure the box to the wall or support. Where possible position the battery box away from water
ZLWKWKHFDEOHRXWOHWIDFLQJWRZDUGVWKHÀRRU3. Remove the box lid from the battery box.
Connect the battery box and the solenoid valve as shown above.
5. &RQQHFWWKHUHPDLQLQJFDEOHIURPEDWWHU\ER[WRWKHFRQGXFWLQJULQJ+¿WWHGRQWKHWDS
!
%/$&.&$%/(RED
&$%/(SWITCH /('/,*+7

9
7. OPERATING ELECTRONICS
ON
1
2
3
!
4
D237,&$/6(16257$31. If using a mains supply box turn the power supply switch on. If you are using a battery box insert
the supplied battery. After that switch the water on.
2. ,PPHGLDWHO\ORRNDWWKHEODFNLQIUDUHGVHQVRUWRVHHLILWLVÀDVKLQJWRLQGLFDWHLWLVSRZHULQJXSWKHÀDVKHVVKRXOGVWRSDIWHUVHFRQGV3. 3ODFHKDQGXQGHUQHDWKWKHWDSDQGHQVXUHVHQVRUZLOOÀDVKUHGIRUVHFRQGVVHQVRUWULJJHUVDQGZDWHUÀRZVRXW5H¿WWKHPDLQVVXSSO\ER[OLGRUWKHEDWWHU\ER[OLGDQGHQVXUHDOOFDEOHVDUHVHFXUHDQGwatertight in their respective glands.
7KHVHQVRUKDVEHHQSUHFRQ¿JXUHGWRWKHRSWLPXPGHWHFWLRQUDQJH,QWKHUDUHFDVHWKDWWKHVHQVRUdoes not reliably detect the presence of a user, please contact technical support for guidance on how
to adjust the sensor range.
MAINS %$77(5<

10
A
Q
U
A
S
TO
P
1
2
3
!
4
7b. CAPACITIVE SENSOR TAP
1. Fit the battery into the battery box, then switch the water on.
2. ,PPHGLDWHO\ORRNDWWKHEODFNLQIUDUHGVHQVRUWRVHHLILWLVÀDVKLQJWRLQGLFDWHLWLVSRZHULQJXSWKHÀDVKHVVKRXOGVWRSDIWHUVHFRQGV3. 3ODFH\RXUKDQGXQGHUQHDWKWKHWDSDQGHQVXUHWKHLQIUDUHGVHQVRUWULJJHUVDQGZDWHUÀRZVRXW5H¿WWKHPDLQVVXSSO\ER[OLGRUWKHEDWWHU\ER[OLGDQGHQVXUHDOOFDEOHVDUHVHFXUHDQGwatertight in their respective glands.
7KHVHQVRUKDVEHHQSUHFRQ¿JXUHGWRWKHRSWLPXPGHWHFWLRQUDQJH,QWKHUDUHFDVHWKDWWKHVHQVRUdoes not reliably detect the presence of a user, please contact technical support for guidance on how
to adjust the sensor range.

11
Use soft damp cloth to wipe
Use soft dry cloth to dry the tap
Use mild detergent to clean
Occasional mantenance
Never use abrasive household
cleaners or scourers
Avoid using sharp tools
Never use concentrated or strong
bleach when cleaning
8. MAINTENANCE
10. TROUBLESHOOTING
If the tap is not working please see the trouble
shooting diagram on the next page for guidance.
9. IMPORTANT DETAILS
Customer Reference Data must be completed and be stored carefully for
warranty purposes.
Customer Reference Data
Date of Purchase
Supplier
Supplier Contact no.
Model Type
Installer
Installer Contact details
23(5$7,1*3(5)250$1&(Maximum Static Pressure 6.0 Bar
Optimum Operating Pressure 2.0 - 2.5 Bar
Minimum Flow Pressure - Hot
and Cold
0.2 Bar
Temperature Range 5oC - 60oC

12
IF THE POWER SUPPLY IS LIVE AND SWITCHED ON?
IS THE GREY POWER CABLE FROM THE SENSOR IS CONNECTED TO THE POWER SUPPLY PACK?
IF GREY CABLE IS DAMAGED?
TEST SUPPLY TERMINAL FOR POWER USING MULTIMETRE / VOLTAGE TESTER
ESTABLISH POWER SUPPLY TO TAP
ENSURE PLUG IS FULLY PUSHED HOME IN POWER SUPPLY PACK
REPLACE TAP OR SENSOR IF THE DAMAGE IS EVIDENT
IF SUPPLY CABLE IS OFFERING POWER TO THE SUPPLY PACK BUT PRODUCT NOT RUNNING, REPLACE SUPPLY PACK
IF INCORRECT, RECONNECT
IF THE WATER SUPPLY IS LIVE & SWITCHED ON?
ESTABLISH WATER SUPPLY TO TAP
IF FILTER IS BLOCKED?
CLEAN / REPLACE FILTER
ARE THE CONNECTIONS TO SOLENOID CORRECT? GO TO SECTION 6 TO CONFIRM
CONNECT CABLES TO SOLENOID TERMINALS.
ARE RED & BLACK SENSOR CABLES DAMAGED?
REPLACE TAP / SENSOR IF DAMAGE IS EVIDENT
IF SOLENOID VALVE IS WORKING?
REMOVE RED & BLACK CABLES FROM SOLENOID AND PLACE TERMINALS OF A 6V BATTERY ON THE SOLENIOD CONNECTORS. REVERSE THE POLARITY TO OPEN AND CLOSE THE VALVE. IF SOLENOID DOES NOT FUNCTION THEN REPLACE
SENSOR DISTANCE IS TOO GREAT FOR ROOM
IF FILTER IS BLOCKED?
INSPECT SOLENOID DIAPHRAGM FOR DEBRIS
CHECK INCOMING WATER SUPPLY
CLEAN/ REPLACE FILTER
CLEAN / REPLACE DIAPHRAGM & ENSURE FILTER IS INSTALLED IN SOLENOID INLET CONNECTOR
IF SOLENOID VALVE IS WORKING?
REMOVE RED & BLACK CABLES TO SOLENOID AND PLACE THE TERMINALS OF A 6V BATTERY ON THE SOLENIOD CONNECTORS. REVERSE THE POLARITY TO OPEN AND CLOSE THE VALVE. IF SOLENOID VALVE DOES NOT FUNCTION THEN REPLACE
CONTACT TECHNICAL SUPPORT
NO FLASHING WHEN
SWITCHED ON
NO WATER FLOW
FROM TAP
POOR FLOW RATE
THROUGH TAP
CHECK CHECK CHECK CHECK
IF THE PRESSURE IS 0.2 BAR MINIMUM?
ADJUST THE PRESSURE IN BETWEEN 0.2 TO 3.0 BAR
TAP KEEPS
RUNNING/DRIPPING
EMAIL: [email protected] | TELEPHONE: [phone] | FAX: [phone]
IF PRODUCT IS FED THROUGH A TMV ENSURE THE TMV IS TESTED FOR CORRECT OPERATION. ISSUES OF THIS NATURE WOULD NOT BE PRODUCT RELATED AND WILL REQUIRE FURTHER INSPECTION OF THE WATER SUPPLY
ARE THE CONNECTIONS TO SOLENOID CORRECT? GO TO SECTION 6 TO CONFIRM

2SWLFDOVHQVRUWDS127()RUWKHPDLQVVXSSOLHGYHUVLRQDGRXEOHSROHVZLWFKHGIXVHGVSXU¿WWHGZLWKD$IXVHDQGZLWKDPLQLPXPFRQWDFWVHSDUDWLRQRIPP0867%(XVHGWRVXSSO\WKHGHYLFHZLWK9$&SRZHUThe point of connection to the mains should be readily accessible and adjacent to the device.
6HQVRUH\HFRQWUROOHUSolenoid
YDOYH%DWWHU\3RZHU6XSSO\&RQWURO0RGXOH7UDQVIRUPHU0DLQV3RZHU6XSSO\&RQWURO0RGXOH7UDQVIRUPHU9'&2SHUDWLQJWHPSHUDWXUHVWRoC.
6WRUDJHWHPSHUDWXUHVo&WRoC.
The sensor has 2 cables leading out of
the rear of the lug; these cables should
never be extended (Unless the correct
extension cables are used.) 9%LVWDEOHlatching
Connection
to control
module is
via 2 spade
connectors %R['LPHQVLRQ[[PPMaterial: ABS
%DWWHU\9P$Ktype CR-P2 6XSSO\9DF+]Output voltage
9GFP$Permanent,
P$PVBox Dimension: 95
[[PP&DSDFLWLYHVHQVRUWDS6ROHQRLGYDOYH%XLOWLQFRQWUROOHUPRGXOHDQGEDWWHU\VXSSO\9%LVWDEOHlatching
Connection to
control module
is via 2 spade
connectors %R['LPHQVLRQ[[PPMaterial: ABS
%DWWHU\9P$KW\SH&539'&2SHUDWLQJWHPSHUDWXUHVWRoC.
6WRUDJHWHPSHUDWXUHo&WRoC.
The sensor has 2 cables leading out of the rear of the lug; these cables should
never be extended (Unless the correct extension cables are used.)
All Performa electronic taps conform to relevant parts of the following directives:
(0&'LUHFWLYH(8/RZ9ROWDJH'LUHFWLYH/9'(8NOTE: All electrical installations must comply
ZLWKFXUUHQW,(7DQG52+6:(((UHJXODWLRQV11. ELECTRICAL SPECIFICATION

14
12. TEMPLATE
'ULOOLQJPPKROHIRUBackplates only
Deck mount
Wall mount
Wall mount

30
12.5
23.4
30
5.0
30
30

15
TECHNICAL SUPPORT
EMAIL
[email protected]
TELEPHONE
0800 156 0500
FAX
0800 156 1012
Follow us on
HEAD OFFICE
Pegler Yorkshire Group Limited
St. Catherine’s Avenue, Doncaster,
South Yorkshire, DN4 8DF, England
Tel: [phone]
Fax: [phone]
Email: [email protected]
UK ENQUIRIES
UK SALES
Free Phone: [phone]
Free Fax: [phone]
Email: [email protected]
BROCHURE HOTLINE
Free Phone: [phone]
Free Fax: [phone]
Email: [email protected]
INTERNATIONAL ENQUIRIES
EXPORT
Tel: [phone]
Fax: [phone]
Email: [email protected]