PELIOS SE8 User manual

Owner’s Guide
SE8 ANC Wireless Headphones

Please read and keep all safety and use instructions.
WARNINGS/CAUTIONS
• Do NOT use the headphones at a high volume for any extended period.
– To avoid hearing damage, use your headphones at a comfortable, moderate volume level.
– Turn the volume down on your device before placing the headphones in/on your ears, then turn
the volume up gradually until you reach a comfortable listening level.
• Do NOT use your headphones while driving for phone calls or any other purpose.
• Do NOT use the headphones with noise cancelling on at any time the inability to hear surrounding
sounds may present a danger to yourself or others, e.g., while riding a bicycle or walking in or near
traffic, a construction site or railroad, etc.
– Remove the headphones, or use the headphones with noise cancelling off and adjust your volume,
to ensure you can hear surrounding sounds, including alarms and warning signals.
– Be aware of how sounds that you rely on as reminders or warnings may vary in character when using
the headphones.
• Do NOT use the headphones if they emit any loud unusual noise. If this happens, turn the headphones off and
contact Pelios customer service.
• Remove headphones immediately if you experience a warming sensation or loss of audio.
• Do NOT use mobile phone adapters to connect headphones to airplane seat jacks, as this could result in injury
or property damage due to overheating.
• Do NOT use the headphones as aviation communication headsets except in case of emergency.
– No incoming audio will be heard with a discharged or improperly installed battery. This could result in
the potential of missed communications while piloting an aircraft.
– Extremely loud ambient noise levels common to many propeller-driven aircraft may impair your ability to
receive incoming audio communications, particularly during takeoff and climb out.
– The headphones are not engineered for noise conditions, altitude, temperature or other environmental
conditions common in non-commercial aircraft, resulting in possible interference to critical communications.
• To reduce the risk of fire or electrical shock, do NOT expose this product to rain, liquids or moisture.
• Do NOT make unauthorized alterations to this product.
• Use this product only with an agency approved power supply which meets local regulatory requirements
(e.g., UL, CSA, VDE, CCC).
• Do NOT expose products containing batteries to excessive heat
(e.g. from storage in direct sunlight, fire or the like).
Contains small parts which may be a choking hazard. Not suitable for children under age 3.
This product contains magnetic material. Consult your physician on whether this might affect your
implantable medical device.
IMPORTANT SAFETY INSTRUCTIONS

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Pelios could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation
This device complies with FCC and Industry Canada radiation exposure limits set forth for general population.
It must not be co-located or operating in conjunction with any other antenna or transmitter.
Meets IMDA Requirements.
CAN ICES-3 (B)/NMB-3(B)
Management Regulation for Low-power Radio-frequency Devices
Article XII
According to “Management Regulation for Low-power Radio-frequency Devices” without permission granted by the NCC, any company,
enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as
performance to an approved low power radio-frequency devices.
Article XIV
The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; if found, the user shall
cease operating immediately until no interference is achieved. The said legal communications means radio communications operated in
compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave
radiated devices.
DON’T attempt to remove the rechargeable lithium-ion battery from this product. Contact Pelios or another qualified professional
for removal.
REGULATORY INFOR M ATIO N
Do NOT incinerate.

REGULATORY INFORMATION
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the
environment. For more information on disposal and recycling of this product, contact your local municipality, disposal
service, or the shop where you bought this product.
Removal of the rechargeable lithium ion battery in this product should be conducted only by a qualified professional.
Please contact Pelios customer service at https://www.ipelios.com for further information.
This product is covered under warranty for a period of 12-month.
E-mail: [email protected]
Phone: [phone] ( Mon-Fri 9:00 a.m. to 4:00 p.m. PST ) Recommend
Website: https://www.ipelios.com
Facebook: https://www.facebook.com/ipelios
Instagram: https://www.instagram.com/ipelios
If you have any quality problems about the product , please contact Pelios customer service.

WHAT’S I N T HE C A R T O N
Contents
Confirm that the following parts are included:
USB cable 3.5 mm audio cable
Note: If any part of your product is damaged, do not use it. Contact your authorized Pelios customer service.
E-mail: [email protected]
Phone: [phone] ( Mon-Fri 9:00 a.m. to 4:00 p.m. PST ) Recommend
Website: https://www.ipelios.com
Facebook: https://www.facebook.com/ipelios
Instagram: https://www.instagram.com/ipelios
PELIOS SE8
active noise cancelling Bluetooth headphones
Carry case
Airline headphone adapter
3.5mm to 6.5mm audio converter

HEADPHONE C O N T R O L S
Noise cancellation on/Off switch
Volume up / Skip forward button
Power / Bluetooth / Call control button
Volume down / Skip backward button
USB charging port
Audio jack
Press and hold for 1.5 seconds, until the indicator flashes a blue light for one
second and you hear the ‘power-on’ tones.
Press and hold for 3.5 seconds, until the indicator flashes a red light for one
second and you hear the ‘power-off’ tones.
Power on
Power off

Short press the button
Short press the button
Press and hold for 2 seconds
While on a call, press once
While on a call, press and hold for 2 seconds
With two active calls, press and hold for 2 seconds
Short press the Multi-function button
Long press the button
Long press the button
Short press the button
Short press the button
The Multi-function button and microphone are located on the back of the right earcup.
H E A D P H O N E C O N T R O L S
Headphone functions
Media playback and volume functions
Call functions
The headphone controls are located on the right earcup.
Function What to do
Play /Pause
Skip forward
Skip backward
Volume up
Volume down
Function What to do
Answer a call
End a call
Decline an incoming call
Answer a second incoming call
and put the current call on hold
Decline a second incoming call
and stay on current call
Switch between two calls

NOISE CANCELLATION & AMBIENT SOUND
Noise Cancelling Modes
Active Noise cancellation (ANC) reduces unwanted noise providing a clearer, more lifelike audio performance. You can
choose the noise cancelling mode based on your listening preferences and environment
.
Ambient Sound Modes
Turn on Ambient modes to control how much surrounding noise you let in. With Quick Ambient Mode, you can listen in on
street traffic, catch flight announcements, and hear when your kids or coworkers call out to you.
Summary: Turn on the noise Cancellation function of your headphones if you want to listen to music without the interruption
of surrounding noise. Turn on Ambient Sound Mode if you want to hear the sounds around you.
Switch Between Noise Cancellation and Ambient Sound Modes
Active Noise Cancelling
Active Noise Cancelling (ANC) mainly focuses on cancelling out lower frequency sounds like engines, aviation environment,
trains, traffic noise, etc, so our valuable customers can focus on their music, movies, or books without being disturbed by
outside noises. Our ANC headphones incorporate a microchip that measures ambient sound and generates a waveform that
is an exact negative of the ambient sound and mixes it with any audio signal our customers desire. This makes it possible to
enjoy audio content without having to raise the volume to excessive levels. Please do note, ANC does not cancel
out noises like snoring, talking, music or high-frequency sounds, etc.
BATTERY CHARGING
Charge the headphones
Notes:
• While charging, the battery indicator will light up red. When the battery is fully charged, the battery indicator will turn blue.
• When using Bluetooth with noise cancelling, a full charge powers the headphones for up to 20 hours.
Notes:
• When only use Bluetooth without noise cancelling, a full charge powers the headphones for up to 25 hours.
• When use Bluetooth with noise cancelling, a full charge powers the headphones for up to 20 hours.
Charging time
Allow up to 5 hours to fully charge the headphones.
1. Plug the small end of the USB cable into the micro-USB connector on the left earcup.
2. Plug the other end into a USB wall charger or computer that is powered on.
1, Please make sure headphone is turn on;
2, Short press the NC button, enable the noise canceling function;
3, Short press the NC button again, switch to Ambient Sound Mode;
4, Short press the NC button again, both noise canceling function and Ambient Sound Mode is off.
Tip: Each press of the NC button changes the function. Loop in turn.

STATUS INDICATO R S
BLUETOOT H C O N N E C TIO N S
Connection method
You can connect your mobile device with your headphones using Bluetooth wireless technology.
Note: If connected to an Apple device, the device displays the headphone battery level near the upper right corner
of the screen.
Note: The devices must be within range (49.2 ft. or 15 m) and powered on.
Tip: Once powered on, the LED flashes blue and red alternately.
Tip: Once paired, you hear “Connected” and see the indicator flash blue slowly.
Choose “PELIOS SE8” to connect
2. On your mobile device, enable the Bluetooth feature.
Tip: The Bluetooth feature is usually found in the Setting menu.
3. Select your headphones from the device list.
1.Turn on the headset. If connecting for the first time, the headphone will
enter the pairing mode automatically after it is powered on.
PELIOS SE8
Solid green Noise cancellation ON
Indicator Light Display
Flashing blue and red alternately
Flashing red
Solid red
Solid blue
Flashing blue slowly
System status
Power on & In pairing mode
Low Battery
Charging in Process
Fully Charged
Paired
Indicator Light Display System status
Connect using the Bluetooth menu on your mobile device

BLUE T OOT H C O NNE C TION S
Disconnect a mobile device
Reconnect a mobile device
Connect another mobile device
1. Use the Bluetooth menu on your mobile device to disconnect your mobile device.
2. Power off headphones.
When powered on, the headphones try to reconnect with the last-paired device.
Note: The devices must be within range (49.2 ft. or 15 m) and powered on.
1.Disconnected on your first mobile device.
2.Connected on your second mobile device.
Note: You only can connect one device at a time.
Clear the headphone pairing list
1. Press and simultaneously and hold for 3.5 seconds.
2. Delete your headphones from the Bluetooth list on your mobile device. All devices are cleared and the headphones are
ready to connect.
If you still have issue, contact Pelios customer service.
E-mail: [email protected]
Phone: [phone] ( Mon-Fri 9:00 a.m. to 4:00 p.m. PST ) Recommend
Website: https://www.ipelios.com
Facebook: https://www.facebook.com/ipelios
Instagram: https://www.instagram.com/ipelios

WIR E D C O N N E C T ION S
C A R E A N D M AINTEN A N C E
Clean the headphones
Warranty
If you still have issues, contact Pelios customer service.
Your headphones may require periodic cleaning.
• Wipe the outside surfaces with a soft, dry cloth.
• Don’t allow moisture to get inside the earcups or the audio input connector.
Your headphones are covered by a 12-month warranty. Visit our website at www.ipelios.com for details of the warranty.
To register your product, visit www.ipelios.com for instructions. Failure to register will not affect your limited warranty rights.
E-mail: [email protected]
Phone: [phone] ( Mon-Fri 9:00 a.m. to 4:00 p.m. PST ) Recommend
Website: https://www.ipelios.com
Facebook: https://www.facebook.com/ipelios
Instagram: https://www.instagram.com/ipelios
Connect the audio cable
Use the 3.5 mm cable (provided) to connect a non-wireless device or to continue using the headphones.
Airline Headphone Adapter3.5mm to 6.5mm Audio Converter
Store your headphones
Place the headphones flat into the case.
Notes: • Make sure to power off the headphones when not in use.
• Before storing the headphones for more than a few months, make sure the battery is fully charged.
3.5mm 6.5mm

TROUBLESHOOTIN G
Common solutions
If you experience problems with your headphones:
• Check the state of the status indicators (see page 10).
• Charge the battery (see page 9).
• Increase the volume on your headphones, mobile device and music app.
• Try connecting another mobile device (see page 11).
If you could not resolve your issue, see the table below to identify symptoms and solutions to common problems. If you are unable to
resolve your issue, contact Pelios customer service.
If you still have issues, contact Pelios customer service.
Symptom Solution
Headphones don’t power on Charge the battery.
Poor sound quality
• Use a different music source.
• Connect another mobile device.
• Disconnect the second device.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
Headphones don’t connect
with your mobile device
• Check the state of the status indicators.
• Disconnect the back-up audio cable.
• Disconnect the USB charging cable.
• On your mobile device:
- Disable the Bluetooth feature and then re-enable.
- Delete your SE8 from the Bluetooth list on your device. Connect again.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
• Connect another mobile device.
• Clear the headphone pairing list and connect again.
E-mail: [email protected]
Phone: [phone] ( Mon-Fri 9:00 a.m. to 4:00 p.m. PST ) Recommend
Website: https://www.ipelios.com
Facebook: https://www.facebook.com/ipelios
Instagram: https://www.instagram.com/ipelios

Symptom Solution
No sound
Cannot hear on a call
• Power on the headphones and charge the battery.
• Check the state of the status indicators.
• Increase the volume on your headphones, your mobile device and music source.
• Slide the Power/Bluetooth switch to the right and release to hear the connected
device. Make sure you are using the correct device.
• Move your mobile device closer to the headphones and away from any
interference or obstructions.
• Use a different music source.
• Connect another mobile device.
Noise beeping
Bad Bluetooth connection
• If the Bluetooth signal is weak, out of range, or suffering from interference,
the connection may fail or cut in and out, leading to choppy audio. Please try the
below steps to resolve such connection issues:
• A Bluetooth signal can be affected if there is too much external interference (signals
from other devices, radio waves, etc.). Try moving to a different area to see if
interference to your connection is resolved.
• The distance between your headphones and the device its paired to should not
exceed 15 meters. If you are outside of this range, you may lose connection.
• The battery may be running low and requires a recharge.
• Check if the network signal is OK (whether the player is in buffer).
• If the connection between your device and the headphones is still unstable, it’s
possible your device may be utilizing an older version of Bluetooth. If possible,
update the Bluetooth on your device or consider testing the connection with a
more modern device.
• Check that headphones and the connected device (i.e., smartphone) are turned on.
• Turn up the volume of the connected device if it is too low.
• Check the audio settings of the Bluetooth device to make sure the sound comes
from the headphones during a call.
• Re-establish the connection using the Bluetooth device.
• While listening to music with the headphones, stop playback and press the button
on the right or left unit to respond to an incoming call.
• Due to weak Bluetooth signals or external signal interference. In this case, move
away fromwireless routers or microwaves and move your headphone closer to
the Bluetooth device.
• Avoid using the headphones for a long time, otherwise the sound will be intermittent,
please reuse after a period of rest.
Listening to music when
the battery is depleted
• Even in wired mode, there must still be some battery power left in your headphones.
These headphones do not support wired use if the battery is fully discharged.

Symptom Solution
No sound from a device
connected by the back-up
audio cable
Poor sound quality from a
device connected by audio cable
Battery won’t charge
• Secure the ends of the back-up audio cable.
• Increase the volume on your headphones, your mobile device and music source.
• Connect another device.
• Secure the ends of the back-up audio cable.
• Connect another device.
• Secure the ends of the USB charging cable.
• Try another charging source.
• If your headphones have been exposed to high or low temperatures,
let the headphones return to room temperature and try charging again.
Noise cancelling function
doesn't work
• Make sure that the noise cancelling function is turned on properly.
• Make sure both of the headphone’s earpads are fitted properly around your ears to
ensure noise cancelling works as effectively as possible.
• Remember, noise cancelling only reduces low frequency sounds such as airplanes,
trains, vehicles, etc. High-frequency noises, such as human voices, will still be audible.

Warranty Card
Certificate
Warranty card number
User name
User phone
User address (including zip code)
Purchase date
Invoice number
Seller name
Seller address (including zip code)
Seller phone no.
Product number
Inspector
Date
Register Warranty On-line at: www.iPELIOS.com
WARRANTY IS VOID IF THE WARRANTY
REGISTRATION IS NOT COMPLETED AND CONFIRMED

[email protected]
@ipelios
@ipelios
www.ipelios.com
+1.888.746.7439