Pelonis FS40-16CR User manual

Electric Fan
FS40-16CR
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2017
Attention: Pictures in the IM are for reference only.
OWNER’S MANUAL

Read Rules for Safe Operation and Instructions Carefully.
CAUTION
IMPORTANT SATETY INSTRUCTIONS
WARNING
1.Do not leave the fan running unattended.
2.Keep electrical appliances out of reach from Children or infirm persons. Do not let
them use the appliances without supervision.
3.This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat this safety feature.
4.If the supply cord is damaged, it must be replaced by manufacturer or its
service agent or a similarly qualified person to avoid a hazard.
5.This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Young children should be supervised to ensure that
they do not play with the appliance.
6.When the fan was assembled, the rotor blade guard shall not be taken off anymore
• Prior cleaning unplug the fan.
•The rotor guard shall not be dissembled/opened to clean the rotor blades.
• Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.
7.WARNING—To reduce the risk of fire or electric shock, Do not use this fan with any
solid-state speed control device.
8.This product employs overload protection (fuse). A blown fuse indicates an overload
or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded or returned to an authorized service
facility for examination and/or repair.
a) “Do not operate any fan with a damaged cord or plug. Discard the fan or return it to
an authorized service facility for examination and/or repair.”
b) “Do not run the cord under carpeting. Do not cover it with throw rugs, runners, or
similar coverings. Do not route the cord under furniture or appliances. Arrange the cord
away from traffic area and where it will not be tripped over.”

INSTALLATION INSTRUCTIONS
Name of components
1.Base Installation：
Align the tube with the
groove on the base. Fix
them together by screwing
the nut at bottom..
Position the rear grill
against the motor so that
the pins on the motor fit
through the matching holes
of the rear grill.
Tube
Motor
Motor shaft
Rear grill
Tighten
knob
3.Install by
aligning
Base
Nut
Considerate Hint:
Remove parts from the component
before performing installation.
RULES FOR SAFE OPERATION
1. Never insert fingers, pencils, or any other object through the
grill when fan is running.
2. Disconnect the fan when moving from one location to another.
3. Be sure the fan is on a stable surface when operating to avoid
overturning.
4. DO NOT use it by window, rain may create electrical hazard.
5. Household use only.
3.Install the Rear grill:
2.Connect the Tube to
Motor:
Adjusting the
tighten knob and insert
the motor part.

Lock nut of grill
Lock nut of blade
Blade
4. Tighten the Rear grill by screwing
the lock nut of grill clockwise.
6. Tighten the Blade:
Screw the lock nut
of blade anticlockwise
5. Install the Blade: Put the fan blade
through the motor shaft. After installment,
gently rotate the blade to check whether it works normally.
Front grill
Grill
Lock
1
2
3
1
2
3
Align the Front Grill with the
Rear Grill at the illustrated
position.
Press them gently as the
figure to check if the two
grills are well connected.
Fix the Grill Lock
with a screw.
7. Front and Rear Grills Installation
3. Be sure the fan is on a stable surface when operating to avoid

Instructions for display of body
Instructions for key of remote controller
INSTRUCTIONS FOR USE
MODE
DRIVE PLATE ON/OFF
PRO/Timer
OSC
Considerate Hint:
1. Install the battery with the positive side facing up.
2. Effective Range of Remote Control: within 5 meters
distance and 30-degree deflection in front of
Product.
Battery installation
Rear
cover
PUSH OPEN
Speed / Timer display
Timer
Sleep
Natural Silent

Remote Control:
Drive Plate
Rotate it to adjust the speed/time setting (Clockwise for increase, Anticlockwise for
decrease)
ON/OFF Key
Press it once, the fan will turn on at normal mode. Press it again to shut off. (The fan
starts at speed 01. Rotate the Drive Plate clockwise for higher speed. The wind
speed ranges from 01 to 12 with an increment of 1)
OSC Key
After the fan starts, press this key once to start oscillation. Press the key again to
stop it at the desired direction.
Mode Key
After turning on the fan, press it repeatedly to choose the mode in order of
“Sleep-Natural-Silent”. Press it the fourth time and exit to the normal mode.
PRO/Timer Key
a. Setting a Starting Time: Plug in the unit. Press this key once without turning on
the fan. Rotate the Drive Plate to select time from “0.5 to 12 hours”with an increment
of 0.5. (The increment increases to 1 after the number reaches 10 hours) The
starting time was set up when the number on screen flashes once. Then a clock
signal will be on display. And the fan will automatically turn on at your setting time.
b. Setting a Stopping Time: After turning on the fan, press this key into time
setting. Rotate the Drive Plate as above to select time. The stopping time was set up
after the number flashes once. And the clock signal will be on screen. Then the fan
will automatically turn off at the appointed time.
(PS: To exit time setting, press the PRO/Time Key again. To cancel the time setting,
press the time key once, rotate the hour to 00. Wait for 5-10 seconds, the former time
setting was canceled when the clock signal disappears on screen.)
The fan will auto shut off after 12 hours without operation.

Instructions for operation of body
INSTRUCTIONS FOR USE
Body key
Height
Adjustment
Knot
Height Adjustment
Screw the knot clockwise
and loosen it for adjusting
the height
Drive Plate: Rotate it to adjust the speed/time setting
Mode Button: Repeatedly press the mode button in the middle, and select
modes in the cycle of “Normal-Sleep-Natural-Silent-Normal”.
OSC Button: Press it once to start oscillation. Press the button again to stop it
at the desired direction.
On/OFF Button: Press it once to turn on the fan at Normal mode. Press it
again to turn off.

CLEANING
1. Be sure to unplug the fan from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else
the product will be damaged or cause accident.
2. When you feel it hard to operate, please make sure you have got the right way.
a) Grasp the plug and remove it from the receptacle
or other outlet device. Do not unplug it by pulling
on cord.
b) Open the fuse cover. Slide to open the fuse access
cover on top of the attachment plug towards blades.
c) Remove the fuse carefully. Insert the tip of your tool into
fuse slot (close with the terminal).Then pry the fuse gradually and
slowly,but not overexert. If it’s tight, you can try it at several times and pry the
fuse little by little. When one side of the fuse has been pried, then you can get
the fuse out entirely.
d) Risk of fire. Replace the fuse only with 2.5 Amp, 125 Volt fuse.
e) Close the fuse cover. Slide to close the fuse access cover on top of the
attachment plug.
f) Risk of fire. Do not replace the attachment plug, which contains a safety
device (fuse) that should not be removed. Discard the product if the attachment
plug is damaged.
USER SERVICING INSTRUCTIONS