Pelonis FZ10-17JR User manual

MODEL: FZ10-17JR
ITEM:809482
OWNER’S MANUAL
36" TOWER FAN
READ AND SAVE THESE INSTRUCTIONS

1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing grilles for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. Do not use fan in window. Rain may create electrical hazard.
6. Ensure that the fan is switched off from the supply mains before removing the grille.
The rules about cord and plug as below:
1. This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from the
outlet. Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the products. If the replacement fuse
blows, a short-circuit may be present and the product should be discarded or
returned to an authorized service facility for examination and/or repair.
2. Do not operate any fan with a
damaged cord or plug. Discard
fan or return to an authorized
service facility for examination
and/or repair.
3. Do not run cord under carpeting.
Do not cover cord with throw
rugs, runners, or similar
coverings. Do not route cord
under furniture or appliances.
Arrange cord away from traffic
area and where it will not be
tripped over.
Read Rules for Safe Operation and Instructions Carefully.
1. This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one
way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safely feature.
2. To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-
state speed control devices.
1
CAUTION
WARNING
PART FIGURE
RULES FOR SAFE OPERATION
Note: All the pictures in this manual are for explanation purpose only. Any discrepancy between
the real object and the illustration in the drawing shall be subject to the real subject.
1. Body
2. Front base
3. Rear base
4. Plastic nut
5. Power cord
1
3
4
2
5

2
1. Take out the fan body and the spare parts from the box. Put the front base onto
rear base and join them together. (See Fig. 1)
2. Pass the power cord through the flute, then insert the fan body into the base.
(See Fig. 3)
3. Fix the fan body on the base with the plastic nut. (See Fig. 2)
I. Remote Controller (Fig.4)
a. KEY INSTRUCTION
1. “ ” ON/OFF KEY
The “ON” key is for switching on the fan .The fan will be
started at breeze step.
Press the “OFF” key if the fan needs to switch off.
2. “ ” SPEED KEY
When the fan started, press this key repeated, the fan will
work with “1-2-3” circulatory.
3. “ ” MODE KEY
Press this key to select mode. The sequence is normal, natural, and sleep when this
key being touched repeatedly or continuously. The light indicate mode state.
4. “ ” OSC/LOUVER KEY
After the fan has started, press this key to select oscillation mode. The lights on the
display can indicate fan oscillation mode.
ASSEMBLY INSTRUCTIONS
The outlet trough
Fig.1
Fig.2 Fig.3
Fig.4
OPERATION INSTRUCTION

5. “ ” TIMING KEY
Press this timer key repeatedly to set the time for air delivery. Increase in
increments up to "1-2-3-4-5-6-7" hours.
b. BATTERIES
(battery not included in the packaging)
(1) Slide the battery compartment Cover.
(2) Insert the batteries, and make sure that the
batteries are placed as shown in the Fig.5.
(3) Slide back the battery cover.
NOTES: Use size “AAA” manganese or alkaline
batteries. Do not use rechargeable batteries.
c. BATTERY WARNING AS BELOW
d. REMOTE CONTROLLER OPERATION
Point the remote controller at the receptor on body of the fan and press the desired
button. The remote controller will work at distances of up to roughly five meters and
the angle of 30 degree included between right and left from the receptor.
The batteries must be removed from the remote controller before it is scrapped and
that they are disposed of safely.
e. OVERHEAT PROTECTION OF THE MOTOR
The windings of the motor have a thermal-fuse that burns out and the fan switches
off and temperature of the motor is no longer going up so that plastic parts of the fan
don’t subject to deformation so far so to be burned by the overheat if the motor is
overheat for any unexpected reason.
3
Fig.5
1. Do not dispose of batteries in fire, batteries may
explode or leak.
2. Do not mix old and new batteries.
3. Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
4. Non-rechargeable batteries are not to be recharged.
5. Batteries are to be inserted with the correct polarity.
6. Exhausted batteries are to be removed from the product.
7. The batteries must be removed from the remote controller before it is scrapped
and that they are disposed of safely.

CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.
a) Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling
on cord.
b) Open fuse cover. Slide open fuse access
cover on top of attachment plug towards blades.
c) Remove fuse carefully. Insert the tip of your tool
into fuse slot (close with the terminal), then prize
the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at
several times and prize the fuse little by little. When one side of the fuse has
been prized, then you can get the fuse out entirely.
d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else
the product will be damage or cause accident.
2. When you feel it hard to be operated, please make sure you have got the right
way.
USER SERVICING INSTRUCTIONS
4
Fig.6
II. Buttons on fan body / Panel indication (Fig.6)
The buttons on the body such as ON/OFF,SPEED, MODE,
TIMER, OSCILLATION have the same functions as those
of the corresponding keys on the remote controller.

For questions or comments,please write to:
Midea America Corporation
Customer Care Center
11411 NW 107th Street,
Suite 12 Miami, FL 33178
[email protected]
1-866-646-4332
5
product

6
ONE (1) YEAR LIMITED WARRANTY
Please read all instructions before attempting to use this product.
In the event of malfunctions or failure of your Fan, simply deliver or send the Fan,
postage prepaid along with PROOF OF PURCHASE, within the warranty period of one (1)
year, to Midea America Corporation. Midea America Corporation reserves the right to
inspect the claimed defective part or parts to determine if the defect or malfunction
complaint is covered by this warranty. Midea America Corporation shall, within sixty(60)days
after receipt of the product, at its option, repair and/or replace the defective part or parts free
of charge. This warranty shall only cover defect arising from normal usage. Midea America
Corporation assumes no responsibility whatsoever if the Fan should fail during the warranty
period by reason of:
Misuse, negligence, physical damage or accidents.
Lack of maintenance (see instructions for proper maintenance).
Repair by any unauthorized party during the warranty period.
Damage caused by connection to an improper input voltage (see specification
label on your Fan).
Midea America Corporation makes no further warranties or representations, express or
implied except those contained herein. No representative or dealer is authorized to assume
any other liability regarding the Fan. The duration of the implied warranty granted under
State law, including warranties of merchantability and fitness for particular purpose are
limited in duration should the duration of the express warranty grant it hereunder. Midea
America Corporation shall in no event be liable for direct, indirect, special or consequential
damages.
Some states do not allow limitations on how long an implied warranty lasts, and/or the above
limitations or exclusion may not apply to you. This warranty gives you specific legal rights
and you may have other rights which vary from state to state.
Midea America Corporation warrants as limited herein to the original purchaser of retail
thateach new Fan, shall be free of defects in material and workmanship for aperiod of
one (1) year from the date of original purchase. This one (1) year warranty is limited to
the Motor and Electric Element.

MANUAL DEL USUARIO
VENTILADOR DE TORRE (91,6cm)
MODELO: FZ10-17JR
ARTÍCULO:809482
LEA Y GUARDE ESTAS INSTRUCCIONES

1. No introduzca los dedos, lápices, u cualquier otro objeto a través de las rejillas
mientras el ventilador esté en funcionamiento.
2. Desconectar si va a desplazarlo.
3. Desconectar si va a quitar las rejillas para limpiar.
4. Asegúrese de que el ventilador esté colocado sobre una superficie estable,
para evitar que se vuelque.
5. No utilizar en una ventana. La lluvia representa un peligro eléctrico.
6. Asegúrese de que el ventilador esté desconectado de la fuente de alimentación
antes de quitar las rejillas.
Normas sobre el cable y el enchufe:
1. Este producto está equipado con una protección contra sobrecarga (fusible).
Un fusible quemado indica que hubo una sobrecarga o un cortocircuito. Si el
fusible se quema, desconecte el aparato de la toma de corriente. Reemplace
el fusible de acuerdo a las instrucciones al usuario (ver el marcado de producto
para el valor nominal de fusible apropiado) Si el fusible de reemplazo se quema,
puede haber un cortocircuito y el producto debe ser desechado o llevado a un
centro de servicio autorizado para
examinar y/o reparar.
2. No operar un ventilador con un
cable o enchufe dañado. Deseche
el aparato o llévelo a un centro de
servicio autorizado para examinar
y/o reparar.
3. No pase el cable de alimentación
por debajo de alfombras. No
cubra el cable con tapetes,
alfombras o similares. No tienda
el cable debajo de muebles u
otros electrodomésticos. Coloque
el cable lejos de áreas de tráfico y
donde no pueda provocar
tropiezos.
Lea las normas de seguridad y las instrucciones atentamente.
1. Este aparato tiene un enchufe polarizado (una pata es más ancha que la otra).
Para reducir el riesgo de descarga eléctrica, el enchufe está diseñado para
encajar en un tomacorriente polarizado de una sola manera. Si el enchufe no
encaja por completo en el tomacorriente, inviértalo. Si aún así no encaja, llame
a un electricista calificado. No trate de violar esta medida de seguridad.
2. Para reducir el riesgo de incendio o descarga eléctrica, NO utilice este ventilador
con un dispositivo de control de velocidad sólido.
1
PRECAUCIÓN
ADVERTENCIA
FIGURA DE LAS PARTES
NORMAS DE SEGURIDAD
Nota: Las imágenes son sólo ilustrativas. Si hay cualquier discrepancia entre el objeto real y
la imagen, tomar el objeto real como referencia.
1. Cuerpo
2. Base frontal
3. Base posterior
4. Tuerca plástica
5. Cable de alimentación
1
3
4
2
5

2
1. Retire el ventilador y sus partes de la caja. Inserte la base frontal en la base
posterior y únalas. (Figura 1)
2. Pase el cable eléctrico a través del tubo, e instale el cuerpo del ventilador en
la base. (Figura 3)
3. Fije el cuerpo del ventilador a la base con la tuerca plástica. (Figura 2)
I. Control remoto (Figura 4)
a. INSTRUCCIONES DE LOS BOTONES
1. “ ” ON/OFF
El botón "ON" es para encender el ventilador. Se iniciará
en nivel de brisa.
Presione el botón "OFF" para apagar.
2. “ ” VELOCIDAD
Una vez encendido el ventilador, presione este botón varias
veces para alternar entre los niveles de velocidad "1-2-3".
3. “ ” MODO
Presione este botón para seleccionar el modo. La secuencia de modos al
presionar este botón repetidamente es: normal, natural y noche. La luz indica el
modo seleccionado.
4. “ ” OSCILACIÓN
Con el ventilador encendido, presione este botón para seleccionar el modo de
oscilación. La luz en la pantalla indica que se ha seleccionado el modo.
INSTRUCCIONES DE MONTAJE
La toma de corriente
Figura 1
Figura 2 Figura 3
Fig.4
GUÍA DE OPERACIÓN