Pentax 76670 User manual

PENTAX Service Co.,Ltd
Technical Service Dep.
04,06 KN
PRODUCT No. 76670
TM
ENGLISH

76670 -1/12-
[TABLE OF CONTENTS]
1. PREPARATION …................................................................................................... 2
1-1 Prepare the SD card for confirmation of adjustment
1-2 Setting the computer and copy the adjustment file to SD card
1-3 Set up the VB run time
2. DISASSEMBY AND ASSENBLY............................................................................ 6
Outline of Disassembly and Assembly..................................................................
2-1 Caution 6
2-2 Chart for Assemble, Adjustment and Confirmation......................................... 6
3.DISASSEMBLY AND ASSEMBLY PROCEDURES.
4.ADJUSTMENTTHEPROGRAMSOFT (SLRfunction)
6
4-1 Setting the computer
4-2 Preparation
4-3 Adjustment display
4-4 Items for Adjustment and checking
4-5 Procedureforadjustment
4-6 Procedure for ending the program soft
5.ADJUSTMENT THE PROGRAM SOFT (Digital function)
5-1Procedureforadjustment
7
7
7
8
9
11
11
11
6.Firmware 12
7. INFORMATION OF JIGS, TOOLS AND TESTERS FOR *ISTDS....................... 12

76670 -2/12-
Summary
*istDL2 (76670) is basically same as *istDL (76570)
The information in this manual is only for istDL2. For other information, please refer to the service
manual for istDL.
The service equipments are common use with istDL except service program soft.
1-1. Preparation for adjustment
Adjustment program soft for 76670（＊ist DL2）--- （Supply with CD-R）
Computer
SD memory card x 2 --- The size of memory should be bigger than 8MB
SD card reader or Camera and USB cable （I-USB17）--- Connect to PC
Preparation for SD memory card
1. Two SD memory card for FW
The following SD card is common use with istDL/istDS
2. For SW test
3. For Test mode ON
4. For test mode OFF
5. For initial set
1-2.Setting the computer and copy the adjustment file to SD card
(1) Copy the [76670 SLR] folder from the Programmed software contained in the CD-ROM to [C: drive] as
shown in the picture below. (For SLR adjustment)
(2) Copy the [76670] folder from the Programmed software contained in the CD-ROM to [C: drive] as shown in
the picture below. (For Digital adjustment)
(3) Copy the file of [kb411b.bin] from [GM_FW] holder
(4) Copy the file of [kb392.bin] from [Product ID FW] --- FW for new T100
76670
76670 SLR

76670 -3/12-
1-3 .Set up the VB run time
If your computer is not installed “VisualBasic” software, set up the VB run time is required as follow.
[Procedure]
①Set the 76670 adjustment program soft into the computer
②Execute the setup.exe in the folder of [vb6run_csx.x.x]
Installer will be started
* The Execute file and uninstall setting file will be generated

76670 -4/12-
③Click OK
④* Do not click Directory, Click installation button

76670 -5/12-
⑤Set up will be started
⑥Click OK to end the installation

76670 -6/12-
2. DISASSEMBY AND ASSENBLY.
2-1. Caution:
◆About FW installation and adjustment after replaced T100
The following procedure will be required ( Same as ＊istDS2（76640）)
2-2. Chart for Assemble, Adjustment and Confirmation.
Procedure of Adjustment and confirmation is same as ＊ist DL（76570）
Refer to the ＊ist DL（76570）Service manual
3, Procedure for Disassemble/Assembly
Procedure of Disassemble/Assembly is same as ＊ist DL（76570）
①FW for new T100
②FW for service
Adjustment

76670 -7/12-
4. ADJUSTMENT THE PROGRAM SOFT (SLR function)
Caution: When replaced T100, the following procedure should be completed
Preparation：
Programmed software for 76670 (for SLR operation), USB cable (I-USB17)
Computer (Windows 2000 / XP), AC-adaptor (D-AC10), Light source (Shutter tester)
Temporary bottom cover (Hand made/exclusive item), Power supply (8V,3A)
Shutter tester (1/4000 can be measured), Diaphragm set ring F8 (KA-0-1A), FA (F) 35-80mm F4-5.6,
AF positioning jig (Square) for 27830, AF positioning jig (Cross) for 27250, Power adaptor,
AF chart for 2m x2 (Exclusive item), AF master lens for 2m, FA Macro 50mmF2.8,
Driver1.5mm (HD-M1.5)、
4-1. SETTING THE COMPUTER
zSetting the computer (Page2) and Set up the VB run time (Page3)
should be completed
4-2. Preparation
When replaced T100 or CCD, the CCD ID number will be used
for digital adjustment
①Install battery cover for battery adaptor and temporally bottom cover
to the camera
②Set focus mode lever to [MF]
4-3. DISPLAY FOR ADJUSTMENT
When start the adjustment software, the following display will be opened
7
66
7
0S
LR
A. Tool Bar
C. Menu display
Adjustment items
Product number
Menu Bar B. USB connecting display
76670

76670 -8/12-
TOOL Bar
Display the status of USB connecting
Display the status of USB connecting
USB Connecting is ON：Connect
USB Connecting is OFF：Unconnect
4-4. MENU Display
When click the items, the detailed will be displayed as follows
Detailed of adjustment items
1：[Eeprom checking] --- Check the data
2：[Exposure adjust] --- Adjustment of exposure
[BV adjust] (brightness value) --- Adjustment of measurement sensor
3：[AF and related adjust] --- Adjustment of AF
[CCD position adjust] --- Adjustment of CCD position
[AGC level adjust] --- Adjustment of AGC level
[Uniformity adjust] --- Adjustment of uniformity
[Focus offset adjust] --- Adjustment of AF focus
Op Start the correspond with Camera
Cl Close the correspond with Camera
p.s Print screen
ver Display FW version
end End of adjustment
m.n Display Menu screen
Connect

76670 -9/12-
4：[Number of repairs] --- Record the number of repair
5：[Eeprom checking] --- Check the data
6：[Battery level adjust] --- Adjustment of Battery level
7：[Shutter speed adjust] --- Adjustment of High shutter speed
4-5. Adjustment procedure
①Turn the power of the camera Off and then install AC adaptor
* Suggest installing battery to avoid the Power supply interception
②Connect the camera to the computer via USB cable
③Turn the power of the camera ON and confirm that the camera is recognized by computer
④Click [PDCAdj01.exe] in the EXE folder
⑤Adjustment screen will be displayed
⑥Click [Op] to start correspond
*Confirmation: [Connect] should display as follow
⑦Execute the check/adjustment following the display screen as follows
1：EEPROM CHECKING
↓
2：EXPOSURE ADJUST
[BV ADJUST]
↓Tools：Focus master lens for 35mm (KML-01), Diaphragm set ring F8 (KA-0-1A)
↓Light source (LV6,LV8,LV12,LV15) or (LV6,LV9,LV12,LV16)
↓
3：AF AND RELATED ADJUST
↓Tools: AF positioning jig (Square) for 27830, AF positioning jig (Cross) for 27250, Light source LV12
↓Driver1.5mm (HD-M1.5), AF master lens for 2m, FA (F) 35-80mm F4-5.6,
↓AF chart for 2m x2 (Exclusive item), FA Macro 50mmF2.8,
↓
Connect
76670
Initialize the data
(Yes/No)
Yes
Replaced Main PCB？
No
T100ExChange
Did you exchange the
main pc board?
PDC Adj
Writing of initial EPROM.
6：BATTERY LEVEL ADJUST