PERCo ST-01 User manual

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
ST-01 Speed gate with swing panels is designed for indoor operation. It is an ideal solution for
sites with high aesthetic and comfort requirements.
Speed gate top covers can be made of tempered glass or stainless steel. The swing panels
of ST-01 can be of different width: 650 mm, 900 mm, and 1000 mm. 900 mm and 1000
mm swing panels are designed for people in wheelchairs, and can be used as an additional
emergency exit. The swing panels are moving away when a passage takes place.
Application
160 W
W
+50
+1
24V
power consumptionoperating
voltage
temperature
range
2
passage
direction
motor drive
60
persons/min
ST-01 Speed gate
ST-01 Speed gate with stainless steel top covers
If an increased number of passage lanes is needed, STD-01
double-sided sections can be installed. Each double-sided
section allows arranging one extra passage lane. Various
versions of ST-01 are available to install optional equipment:
a built-in card reader (the turnstile includes the FP- 01C front
panel), a built-in barcode scanner (with the FP-01Q front
panel), as well as a bracket for installing other optional
equipment (with the FP-01A front panel).
Bracket for mounting optional
equipment

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Operating modes The tracking system is equipped with two levels of infrared sensors: 14 pairs are located on
the upper level and 28 – on the lower one, which guarantees the safety of passage at high
throughput and provides avoiding simultaneous passage of two or more people.
The delivery set includes an RC-panel; the orientation of the RC-panel buttons relative to the
directions of passage is set when connecting to the turnstile.
The powered speed gate operates in normally closed mode. It is possible to switch the turnstile
to the additional "Automatic opening in the selected direction" mode, as well as to adjust the
home position of the swing panels in the "training" mode.
The product provides independent control of the passage in two directions. Control commands:
•passage denial
•authorized single passage in the set direction
•authorized free passage in the set direction
•authorized free passage in both directions
When the power is off, the turnstile panels are unlocked and can be moved manually in any
direction.
ST-01 Speed gate with a built-in card capture reader
ST-01 Speed gate with a post for embedding a barcode scanner
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Housing – stainless steel; section filling – 8 mm tempered glass; top cover – glass and / or
stainless steel; panels – 10 mm tempered glass.
The speed gate can be equipped with 5 types of swing panels.
Design
Passage direction indication
Turnstile mode indication
Turnstile mode indication
Swing panels type Passageway width Passageway height
ATG300 650 mm 915 mm
ATG300H 650 mm 1300 mm
ATG425 900 mm 915 mm
ATG475 1000 mm 915 mm
ATG575 1200 mm 915 mm
Main features •operation of the speed gate from RC-panel, WRC, ACS
•built-in electronic boards
•safe voltage – 24 V
•power consumption – max. 160 W per passage
•two levels of infrared sensors control the passage zone, 14 pairs are located on the upper
level and 28 – on the lower one
•possibility for several users to perform authorized single passages in a row in the same
direction without the panels being closed
•4 versions of panels, both for different passageway widths (600, 900 and 1000 mm) and
with increased height (1300 mm for a passageway width of 600 mm)
•several different versions of the turnstile front panels that allow integrating optional
equipment: a card reader, a barcode scanner, a face recognition terminal, etc.
•if necessary, the number of passage lanes through the turnstile can be increased by
installing STD-01 double-sided sections
•possibility to install proximity card readers inside sections under the glass top cover (overall
reader dimensions – max.155х68х28 mm, reading range – min. 40 mm)
•central sections feature indication blocks of passage grant / denial
•section top covers feature passage indication
•reader interrogation zones are indicated with backlit pictograms
•backlit lateral indication of passage direction
•possibility to adjust the panels position when in the closed position (training mode)
•Fire Alarm input for connecting the emergency passage opening device; when the
command is sent from it, the panels are automatically opened in one direction and it is
possible to walk through the turnstile in both directions
•outputs for connecting remote indication blocks of passage grant / denial, as well as a
sounder (sirens)
•two control modes: pulse and potential; it can operate both as a standalone unit controlled
by the operator using an RC-panel and as a part of ACS
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Size1 and Size2 switches positioning on the St-01.771 control board, depending on the type
of swing panels:
Swing panels type Switches position
Size 1 Size 2
ATG300 ON OFF
ATG300Н ON ON
ATG425, ATG475 OFF OFF
ATG575 OFF ON
The product with regard to resistance to environmental exposure complies with GOST15150-
69 category NF4 (operation in premises with climate control).
The operation of the turnstile is allowed at ambient temperature from +1°C to +50°C and
relative air humidity up to 80% at + 25°C.
It is a serially produced product certified for compliance with applicable Russian and European
CE standards.
Operating
conditions
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
ST01
ST-01/M (Master) section 1
ST-01/S (Slave) section 1
Section top cover 2
Glass swing panel 2
RC-panel with cable 1
Documentation set: Certificate and Operation manual 1
STD01
Section with top cover and mounting kit 1
Glass swing panel 2
RC-panel with cable 1
Certificate 1
Delivery set
Technical
specifications Operating voltage 24 V
Consumption current 6.5 A
Power consumption 160 W
Throughput in single passage mode up to 60 persons / min
Passageway width with ATG-300, AТG-300H swing panels 650 mm
with ATG-475 swing panels 1000 mm
Mean time to failure 5,000,000 passages
Mean lifetime 8 years
ST-01 weight with swing panels 188 kg
STD-01 weight with swing panels max. 118 kg
Overall ST-01 dimensions (without
including FP-01C, FP-01Q, FP-01A
front panels):*
with ATG-300 swing panels 1820х1050х1010 mm
with ATG-300H swing panels 1820х1050х1300 mm
with ATG-425 swing panels 1820х1300х1010 mm
with ATG-475 swing panels 1820х1400х1010 mm
with ATG-575 swing panels 1820х1600х1010 mm
* Overall dimensions when organizing multiple passage lanes using several STD-01
Ltotal = 920n+ 117 0 m+ 12 70 k+ 130 (mm), being:
n– the number of installed pairs of ATG-300 and ATG-300H swing panels;
m– the number of installed pairs of ATG-425 swing panels;
k– the number of installed pairs of ATG-475 swing panels.
Connection The slave section (side of the bidirectional section) is connected by its standard cables to the
Master section (side of the bidirectional section) of one passage lane. The master section
(side of the bidirectional section) is equipped with the ST-01.771 control board (located at the
bottom of the central section post behind the cover plate). All external connections are made
to the board contacts. Microcontrollers installed on the boards control the drives of the swing
panels, process signals from IR sensors, process external commands, and generate signals
about passages through the turnstile.
ST-01.770 control board contacts description by connectors
Connector Contact Electrical
circuit Designation
X1 (POWER) 124V External power supply connection
2 GND
X2 (RC)
1 GND Common
2 UnlockA Direction A control input
3 Stop Control input – passage denial
4 UnlockB Direction B control input
5 LedA Indication output of direction A on the RC-panel
6 LedStop Indication output of passage denial on the RC-panel
7 LedB Indication output of direction B on the RC-panel
8 Sound RC-panel sound signal output
9 FireAlarm Emergency passage opening control input
10 GND
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
SG PS
RI A
RI B
BLACK
WHITE
BLUE
GREEN
YELLOW
ORANGE
RED
BROWN
ACS
OUTPUTS
LEFT BUTTON
STOP BUTTON
RIGHT BUTTON
LEFT INDICATOR
STOP INDICATOR
RIGHT INDICATOR
BUZZER
GND
RC
WRC
LEFT BUTTON
STOP BUTTON
RIGHT BUTTON
GND
ACS INPUTS
SIREN
RED
GREEN
RED
GREEN
RI PS
* ST-01 Speed gate wiring diagram
X3 (ACS)
1 +12 V, GND +12V output for powering additional devices
2 GND Common
3 Alarm1 Siren connection output
4 Alarm2
5 Common Common for PASS A, PASS B outputs
6 PASSA PASS A relay contact (passage in the direction A)
7 PASSB PASS B relay contact (passage in the direction B)
X4
1 NO1 Normally open Light A output contact
2 C1 Common Light A output contact
3 NC Common Light A output contact
4 NO2 Normally open Light B output contact
5 C2 Common Light B output contact
6 NC2 Normally closed Light B output contact
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Layout description
Item Description
А1 Master section (side of the section)
А2 Slave section (side of the section)
А3 RC-panel
А4* Turnstile power supply
А5* Device for sending FireAlarm command
А6*, А6.2* ACS controller
А7* WRC
А8* 12V DC siren
А9.1*, А9.2* Remote indication block
А10* Remote indicators PS
1, 2 DC connection cable
3, 4 CAN connection cable
5 Jumper wire in case there is no Fire Alarm device (A5). Installed by default.
* The equipment is not included in the standard delivery set
Operation
algorithm The speed gate can operate from an RC-panel (included in the delivery set), WRC and ACS
controller.
Operation is performed by applying a low-level signal to Unlock A, Stop and Unlock B
contacts relative to the GND contact. The response to these signals depends on the control
mode selected by the Pulse switch.
Pulse control mode (Pulse switch in the ON position) is when a pulse is applied to the Unlock
A (B) input, the speed gate panels will automatically open for a single passage in the A (B)
direction. The waiting time for the passage being completed does not depend on the duration
of the control pulse and lasts 8 seconds. Sending impulse to the Stop input closes the panels
from any position, thus blocking the passage. Simultaneous sending of pulses to the Unlock A
(B) and Stop inputs places the turnstile in the "Free passage" mode in the selected direction.
It is recommended to use pulse mode when operating from an RC-panel or WRC. The orientation
of the RC-panel buttons can be changed by swapping the wires from the RC-panel that are
connected to the unlock A and Unlock B contacts, as well as Led A and Led B, respectively.
Potential control mode (Pulse switch in the OFF position) is when the control signal is applied
to the Unlock A (B) input, the glass panels slide away in the selected direction during the
entire holding signal time. Sending the control signal to the Stop input closes the sliding panels,
thereby blocking the passage, regardless of the signals at the Unlock A (B) inputs.
Connection of the ST-01 turnstile and STD-01 bidirectional sections to arrange a passage zone with several passage lanes
PS#1
FA
ACS# 1
DC
CAN
PS#2
ACS#2
RS#1 RS#2
ST-01/M STD-01
MASTER
SLAVE
MASTER
SLAVE
DC
CAN
ST-01/SSTD-01
MASTER
SLAVE
DC
CAN
PS#’N’
ACS#’N’
RS#’N’
1 2 ‘N’
STD-01
‘N’
1
2
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Potential mode is recommended when operating from the ACS controller.
Regardless of the selected control mode, PASS A or PASS B signals are generated when passing
in one direction or the other. These signals can inform the ACS controller of the fact of passage.
Emergency opening of the passage lane is performed by removing a low-level signal from the
Fire Alarm contact relative to the GND contact.
The product also features an additional "Automatic opening in the selected direction" mode
(R1 switch in the ON position). This is a mode of free passage through the turnstile in one pre-
selected direction (selected by the R2 switch) with automatic opening and closing of the panels
during passage.
Training mode (R1 switch in the OFF position, and R2 switch on the ST-01.771 control board
in the ON position) allows manually adjusting the home (closed) position of the turnstile swing
panels.
Note
When operating the speed gate from the ACS controller, it is recommended to connect the
RC-panel to the ACS controller.
The maximum allowed cable length from the RC-panel (ACS controller) is 40 meters.
The maximum allowed cable length from the power supply depends on its cross section and
must be:
•for 1.5 mm2cable – 10 meters
•for 2.5 mm2cable – 20 meters
A layout example of the speed gate connection to the ACS controller
Example of
connection to the
ACS CT/L-04.2
XT10
XT6
XT7
XT9 XT3
XT8
XT2
XT1
XT5 S1 XT4
ШС
OUT1
OUT2
OUT4
IN
RC
OUT ОC
RS-485
TCP / IP
+12V
ШС1+
OUT3
ШС1-
ШС2+
ШС2-
NO1
С1
NС1
NO2
С2
NС2
NO3
С3
NС3
NO4
С4
NС4
IN1
GND
IN2
IN3
GND
IN4
FA
GND
DUA
DUSt
DUB
LdA
LdSt
LdB
Buzz
OK2
OK1
+12V
+12V
GND
B
A
GND
+12V
B
A
GND
+12V
LAN TCP / IP PS
GND
+12V
1
2
3
4
1 2 3 4
FA
LEFT BUTTON
STOP BUTTON
RIGHT BUTTON
LEFT INDICATOR
STOP INDICATOR
RIGHT INDICATOR
BUZZER
OUTPUT 6
OUTPUT 5
INPUT 5
INPUT 6
1
+12V
3
4
RS-485 to AI01,
CL201.1, AU05
1 - jumper wire, installed when there is no FA device
1
2
3
4
Reader
1
INPUT 3
INPUT 4
OUTPUT 3
OUTPUT 4
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
1
2
1 2 1 2 1 2
1
2
3
1
2
3
1
2
3
1
2
3
B
A
GND
+12V
Reader
2
X3 «ACS»
6
5
7
2
1
4
COMMON
PASS B
PASS A
UNLOCK A
GND
UNLOCK B
ST-01
RC
WIGHT
BLUE
GREEN
BROWN
YELLOW
ORANGE
RED
BLACK
COMMONX2 «RC»
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Overall
dimensions
55 68
forATG-300 -A=650, 8=920;
for ATG-300H -A=650, 8=920;
forATG-425 -A=900, 8=1170;
forATG-475 -A=1000, 8=1270;
forATG-575 -A=1200, 8=1470
1820
L overall
1300
B
A
1010
915
L overall = 920n+1170m+1270k+130 (mm),
n - number of ATG-300 (ATG-300H),
m - number of ATG-425,
k - number of ATG-475,
p - number of ATG-575
1010
1820
1600
1200
915
575
600
1010
1820
1400
475
600
1000
915
1010
1820
1300
425
600
900
915
1820
1050
650
1010
300
600
915
1820
1050
650
13001300
10101010
300
985985
Overall dimensions
ATG-425 swing panels
ATG-425H swing panels
ATG-450 swing panels
ATG-475 swing panels
With STD-01 central section
With FP-01Q, FP-01A
front panel
With FP-01C front panel
ATG-575 swing panels
ST-01 Speed gate

perco.com linkedin.com/mwlite/company/perco [email protected] [phone]
Warranty The warranty period is 5 (five) years commencing from the date of sale, unless otherwise determined
in the delivery contract of the Product. In case of sale and installation of the equipment by authorized
PERCo dealers and service centers, the warranty starts from the date of commissioning.
Should there be no date of sale on the warranty card, the warranty period shall commence from the
date of manufacture specified in the Certificate and on the Product label.
Mounting
Hole marking for sections mounting and cable entry zone
Foundation requirements: concrete (grade 400 or higher), stone, etc. foundation of at least 150
mm thick, use reinforcing elements (450x450x200 mm) when installing sections on a less steady
foundation.
passage direction
70
40
30
65
1648
850 (1100)
432 (556)
cable entry zones
341 (466)
36 holes
16
70
46
65
850 (1100)
432 (556)
341 (466)
108
30
70
40
46
65
1648
850 (1100)
432 (556)
cable entry zones
341 (466)
22 holes
16
passage direction
ST-01 Speed gate