PERCo ST-11 Installation and operating instructions

Speed gate
ST-11
and double-sided section
STD-11
ASSEMBLY AND OPERATION MANUAL

Speed gate
ST-11
and double-sided section
STD-11
Assembly and operation manual

CONTENTS
1FUNCTION ............................................................................................................................3
2OPERATING CONDITIONS .................................................................................................. 3
3TECHNICAL SPECIFICATIONS............................................................................................ 6
4DELIVERY SET .....................................................................................................................7
4.1 Standard delivery set.......................................................................................................7
4.1.1 ST-11 Speed gate.................................................................................................................. 7
4.1.2 STD-11 double-sided section ................................................................................................ 8
4.2 Optional equipment that can be ordered in addition to the standard delivery set ............. 9
5DESIGN AND OPERATION...................................................................................................9
5.1 Main features...................................................................................................................9
5.2 Design ...........................................................................................................................10
5.2.1 Section ................................................................................................................................. 12
5.2.2 Indication blocks .................................................................................................................. 12
5.2.3 RC-panel.............................................................................................................................. 12
5.2.4 Control board ....................................................................................................................... 13
5.2.5 Control signals ..................................................................................................................... 15
5.2.6 Control modes...................................................................................................................... 16
5.2.7 Speed gate operation algorithm........................................................................................... 17
5.3 Operating devices..........................................................................................................17
5.3.1 RC-panel connection ........................................................................................................... 17
5.3.2 Fire Alarm device ................................................................................................................. 18
5.3.3 Operation from the ACS ...................................................................................................... 19
5.4 Optional devices connected to the speed gate ..............................................................19
5.4.1 PASS outputs....................................................................................................................... 19
5.4.2 Siren..................................................................................................................................... 19
5.4.3 External indication ............................................................................................................... 20
6MARKING AND PACKAGING .............................................................................................20
7SAFETY REQUIREMENTS ................................................................................................. 21
7.1 Installation safety requirements .....................................................................................21
7.2 Operation safety requirements.......................................................................................21
8INSTALLATION ...................................................................................................................21
8.1 Installation details ..........................................................................................................22
8.2 Use the following tools during the installation: ...............................................................22
8.3 Cable length ..................................................................................................................22
8.4 Installation order............................................................................................................22
8.5 Mounting surface marking layouts .................................................................................25
8.6 Speed gate wiring diagram ............................................................................................26
8.7 Training mode ...............................................................................................................28
8.8 “Auto-opening in the selected direction” mode...............................................................28
8.9 Assembly and disassembly of the speed gate components ........................................... 30
8.9.1 Central post cover plate....................................................................................................... 30
8.9.2 Front panel of the side post ................................................................................................. 31
8.9.3 Swing panel ......................................................................................................................... 32
8.9.4 Swing panel cover plate....................................................................................................... 32
8.9.5 Central post indication block................................................................................................ 33
8.9.6 Section top cover ................................................................................................................. 33
8.9.7 Intrusion detectors duct covers............................................................................................ 34
9OPERATION........................................................................................................................35
9.1 Power-up.......................................................................................................................36
9.2 Pulse control mode........................................................................................................36
9.3 Potential control mode ...................................................................................................37
9.4 In case of an emergency ...............................................................................................37
9.4.1 “Emergency” mode .............................................................................................................. 37
9.4.2 "Fire Alarm” mode ................................................................................................................ 37
9.5 Potential failures............................................................................................................38
10 MAINTENANCE...................................................................................................................38
11 TRANSPORTATION AND STORAGE ................................................................................. 38
Appendix 1. Operation algorithm at pulse control mode............................................................ 39
Appendix 2. Operation algorithm at potential control mode....................................................... 39

ST-11 Speed gate, STD-11 Double-sided section
3
Dear Customer!
Thank you for purchasing PERCo product. Please follow instructions given in this Manual
carefully and this high-quality product will provide many years of trouble-free use.
Assembly and Operation Manual for the ST-11 speed gate and STD-11 double-sided section
(hereinafter – the Manual) contains the instructions on safe transportation, storage, installation,
operation and maintenance of the above-mentioned products. The installation must be carried out
by qualified installers in strict accordance with the Manual.
Abbreviations adopted in the Manual:
CLB – control logic board;
PS – power supply;
RC-panel – remote control panel;
WRC – wireless remote control;
ACS – access control system;
Due to continuous improvement of products, the Manufacturer reserves the right to modify, without
previous notice, the product design not aggravating its technical specifications.
1 FUNCTION
ST-11 speed gate (hereinafter – the speed gate) is designed for pedestrian passage control at
entrance points of administrative buildings, banks, shops, railway terminals, airports, etc.
Attention!
ST-11 speed gate is de
signed for the passage of pedestrians taller than 1 m,
otherwise correct operation of the speed gate is not guaranteed. Pass through the
speed gate of children less than 1 m height tall can
only be carried by the hand
accompanied by adults1.
The speed gate features two sections: ST-11/M (hereinafter – Master section) and ST-11/S section
(hereinafter – Slave section). In a standard delivery set the speed gate allows to arrange one
passage lane. The width of the passage lane depends on the chosen swing panel width.
Use STD-11 double-sided section (hereinafter – double-sided section) to arrange more passage
lanes. Each double-sided section provides one extra passage lane.
Note:
Inside the turnstile sections, it is possible to install access card readers as m
anufactured by
PERCo (IR03.1, MR07 OEM, RP-15.2), and by third-party manufacturers.
Access card
readers are not included in the standard delivery set of the turnstile!
The choice of the type
of the reader, the purchase and installation according to the che
ckpoint blueprint and the
ACS
characteristics is the client's (installer's) responsibility. Readers must meet the
following requirements:
Overall dimension (length × width × height) .................................... max. 155×68×28 mm
Read range .................................................................................................... min. 40 mm
2 OPERATING CONDITIONS
The product with regard to resistance to environmental exposure complies with GOST15150-69
category NF4 (operation in premises with climate control).
Operation of the speed gate is allowed at an ambient air temperature from +1°C to +50°C and
relative air humidity 80% at +25°C.
1If the turnstile is installed in children's institutions or in organizations working with children, where more
secure passage mode is required, it is recommended to reflash turnstile controller with a special firmware
(ST11_Children). Its main feature is the safety zone increased to the whole passage zone of the turnstile and
particular operation algorithm when swing panels do not close if at least one sensor of the turnstile is active.
In order to get necessary recommendations regarding the firmware installation, please contact PERCo
technical support team.

Assembly and Operation Manual
4
Figure. 1ATG-300 overall dimensions
Figure. 2ATG-300H overall dimensions

ST-11 Speed gate, STD-11 Double-sided section
5
Figure. 3ATG-425 overall dimensions
Figure. 4ATG-475 overall dimensions

Assembly and Operation Manual
6
Figure. 5Turnstile's overall dimensions when organizing several passage zones
3 TECHNICAL SPECIFICATIONS
Operating voltage1...................................................................................................... 24±2.4 VDC
Current consumption2..................................................................................................... max.6.5 A
Power consumption ..................................................................................................... max. 160 W
Throughput rate in a single passage mode .................................................. up to 60 persons / min
Passageway width:
with ATG-300, ATG-300H swing panel .......................................................................... 650 mm
with ATG-425 swing panel ............................................................................................. 900 mm
with ATG-475 swing panel ........................................................................................... 1000 mm
Number of intrusion detectors:
upper level .............................................................................................................................. 24
lower level .............................................................................................................................. 24
RC-panel cable length 3 min ................................................................................................... 6.6 m
IP rating ................................................................................................................ IP41 (EN 60529)
Electric shock protection class ................................................................................. III (IEC 61140)
1The power supply is connected to the control board located in the Master section (on the Master side of
the double-sided section) and has the “ST-11.771” marking.
2Current consumption and power consumption are given for each product ST-11 and STD-11 individually.
3Maximum allowable cable length of the RC panel is 40 m (supplied upon request).

ST-11 Speed gate, STD-11 Double-sided section
7
Mean time to failure ................................................................................. min. 5,000,000 passages
Mean lifetime ....................................................................................................................... 8 years
Overall dimensions (L × W × H): see Fig. 1 - 5), mm:
with ATG-300 swing panel ......................................................................... 1236×944×1022 mm
with ATG-300H swing panel ....................................................................... 1236×944×1300 mm
with ATG-425 swing panel ....................................................................... 1236×1194×1022 mm
with ATG-475 swing panel ....................................................................... 1236×1294×1022 mm
Note:
Use the following formula to ca
lculate the overall speed gate width in case several passage
lanes are arranged (Fig. 5): L overall= 864 n + 1114 m +1214 k +130 (mm), where:
n–number of ATG-300 and ATG-300H swing panel sets installed;
m – number of ATG-425 swing panel sets installed;
k – number of ATG-475 swing panel sets installed.
Weight (net):
ST-11/M section ..........................................................................................................max 85 kg
ST-11/S section .......................................................................................................... max 85 kg
STD-11 double-sided section ................................................................................... max 100 kg
ATG-300 swing panel ................................................................................................... max 6 kg
ATG-300H swing panel ................................................................................................ max 9 kg
ATG-425 swing panel ................................................................................................... max 8 kg
ATG-475 swing panel ................................................................................................... max 9 kg
4 DELIVERY SET
4.1 Standard delivery set
4.1.1 ST-11 Speed gate
Main equipment:
Section ST-11/M (Master)1....................................................................................................... 1
Section ST-11/S (Slave)1.......................................................................................................... 1
Top cover ................................................................................................... 2 (in a separate box)
Note:
The
type of top cover is to be chosen by the Customer. The following top cover models for
theST-11 speed gate are available:
•STC-11M – made of artificial stone with a built-in indication unit;
•STC-11S – made of stainless still with a built-in rubber patch with a mnemonic image.
Central post indication block ..................................................................................................... 2
Swing panel cover .................................................................................................................... 4
Glass swing panel ...................................................................................... 2 (in a separate box)
Note:
The type of the swing panel is chosen by the customer. The following swing panel models
are available (see Fig. 1, 2, 3, 4):
•ATG-300 – for 650 mm passageway arrangement;
•ATG-300H – increased height swing panel for 650 mm passageway arrangement;
•ATG-425 – for 900 mm passageway arrangement;
•ATG-475 – for 1000 mm passageway arrangement.
RC-panel with cable ................................................................................................................. 1
Jumper ..................................................................................................................................... 3
Installation tools:
Section top cover mounting kit:
M4×16 screw ....................................................................................................................... 8
washer (4) ............................................................................................................................ 8
1Both sections are delivered with dismantled: top covers, swing panels and central indication units.

Assembly and Operation Manual
8
Central post indication block mounting kit:
M5×16 screw ....................................................................................................................... 4
washer (5) ............................................................................................................................ 4
Swing panel cover plate mounting kit:
M4×10 screw ....................................................................................................................... 8
washer (4) ............................................................................................................................ 8
Swing panel mounting kit:
M10×30 bolt ......................................................................................................................... 6
screw nut M10 ..................................................................................................................... 6
washer ............................................................................................................................... 12
plastic plug ........................................................................................................................... 6
Cardboard template for the settling surface marking ................................................................ 1
Technical documentation:
Certificate ................................................................................................................................. 1
Assembly and Operation manual .............................................................................................. 1
Packaging:
Transportation box for the Master and Slave sections .............................................................. 1
Box for section top covers ........................................................................................................ 1
Box for swing panels ................................................................................................................ 1
4.1.2 STD-11 double-sided section
Main equipment:
Double-sided section1............................................................................................................... 1
Section top cover ........................................................................................ 1 (in a separate box)
Note:
The type of top cover is to be chosen by the Customer. The following top cover models for
the STD-11 are available:
•SDC-11M – made of artificial stone with a built-in indication unit;
•SDC-11S – made of stainless still with a built-in rubber patch with a mnemonic image.
Central post indication block ..................................................................................................... 2
Swing panel cover .................................................................................................................... 4
Glass swing panel ...................................................................................... 2 (in a separate box)
Note:
The type of the swing panel is chosen by the customer. The following swing panel models
are available (see Fig. 5):
•ATG-300 – for 650 mm passageway arrangement;
•ATG-300H – increased height swing panel for 650 mm passageway arrangement;
•ATG-425 – for 900 mm passageway arrangement;
•ATG-475 – for 1000 mm passageway arrangement.
RC-panel with cable ................................................................................................................. 1
Jumper ..................................................................................................................................... 3
Installation tools:
Section top cover mounting kit:
M4×16 screw ....................................................................................................................... 4
washer (4) ............................................................................................................................ 4
Central post indication block mounting kit:
M5×16 screw ........................................................................................................................ 4
washer (5) ............................................................................................................................ 4
Swing panel cover plate mounting kit:
M4×10 screw ....................................................................................................................... 8
washer (4) ............................................................................................................................ 8
Swing panel mounting kit:
M10×30 bolt ......................................................................................................................... 6
1The section is delivered with dismantled: top covers, swing panels, top covers and central indication units.

ST-11 Speed gate, STD-11 Double-sided section
9
screw nut M10 ..................................................................................................................... 6
washer ............................................................................................................................... 12
plastic plug ........................................................................................................................... 6
Technical documentation:
Certificate ................................................................................................................................. 1
Packaging:
Transportation box for the double-sided section ....................................................................... 1
Box for section top cover .......................................................................................................... 1
Transportation box for swing panels ......................................................................................... 1
4.2 Optional equipment that can be ordered in addition to the standard
delivery set
IR03.1 (HID / EMM),or MR07 OEM (Mifare), or RP-15.2 (HID / EMM, Wiegand)
type card readers ...................................................................................... 2 per a passage lane
Anchor PFG IH10 ("SORMAT" company, Finland) with screw and washer:
for the ST-11 speed gate ........................................................................................................ 12
for STD-11 section ................................................................................................................... 8
Wireless remote control 1.............................................................................................................. 1
5 DESIGN AND OPERATION
5.1 Main features
•The speed gate allows to perform several authorized single passages in a row in one direction
without the swing panels being closed.
•The speed gate is a normally-open device, which means that when the equipment is de-
energized the swing panels move freely at ±90º angle.
•The intrusion detectors are installed on two levels throughout the speed gate passage lane.
This allows monitoring user’s location inside the passage lane. The speed gate also makes it
possible for several users to be in the same passage lane at the same time.
•There are several swing panel models, that can be chosen according to the passage lane width
and to the operation peculiarities upon making an order.
•Section top covers may be chosen when ordering; they can be made of tempered glass or
stainless steel.
•The number of the passage lanes can be increased with STD-11 double-sided section
installation.
•The turnstile supports two control modes: pulse and potential.
•It is possible to switch the speed gate to “Auto-opening in the selected direction” mode –
entering the speed gate will force the swing panels to automatically open in the preset direction
and to close after the passage is finished.
•The speed gate will generate an alarm signal in all operating modes if the passage lane is
occupied for more than 30 seconds.
•The equipment can operate as an operating device as a part of ACS or as a standalone unit
operated from the RC-panel.
•The speed gate provides the possibility of proximity card readers installation inside the posts
under the glass section top cover.
•The top covers made of the artificial stone (STC-11M,SDC-11M) have the indication units built-in.
•The speed gate features the swing panel position adjustment in the initial (locked) position
(training mode).
•The pass denial / grant indication units on the central block are well seen by the user when
passing the turnstile. It allows the users not to look for other indication units and pass faster.
•The equipment provides the possibility of external indication block connection to duplicate
passage grant / denial indication.
•Acoustic alarm (siren) connection is provided to warn the operator about unauthorized access
attempt.
1The WRC set contains a receiver that is connected to the control board and the transmission unit (pendent).