Perform FX Mini LED Fog 400 User manual

Mini LED Fog 400
PFX400SLED Instruction Manual
CAUTION - ATTENTION - VORSICHT
RISK OF ELECTRIC SHOCK- DO NOT OPEN
RISQUE D’ELECTROCUTION - NE PAS OUVRIR
STROMSCHLAGGEFAHR - NICHT OFFNEN
In Compliance wit t e following directives: RoHS Directive (2002/95/EU) and
WEEE directive (2002/96/EU)
If t is product is no longer functional or reac ed t e end of its usable life, please
take it to an approved recycling plant.

User Manual
PFX400SLED
Dear Customer,
Thank you for purchasing the Perform FX PFX400SLED. With decades of experience in design and production,
Perform FX are one of the leading manufacturers of professional effects and lighting equipment. This fog
machine has been designed and manufactured to the highest of standards, so you can be assured you have
made a good investment.
For your safety and to ensure you make full use of all the features available, please make sure you read this
manual in full.
Important Safety Advice:
• You must read this manual in full before commencing operation.
• The machine should be operated by a responsible and competent adult only.
• Keep this manual in a safe place for future reference.
• Heed all warnings and instructions, both in this manual and on the product.
• Carry and transport this product with care.
• Impact to this machine or dropping may result in serious mechanical failure. The machine should not be
used if it has been sub ected to such incident.
• Turn off and unplug this machine from the mains supply when not in use.
• This machine is not water-proof and should not be used outside.
• In the event of any liquid entering the housing, unplug immediately & contact a qualified engineer.
• You must not attempt to modify this unit
• The manufacturer accepts no responsibility for in ury or damage caused as a result of not following the
manual provided.
Protection from Electric S ock:
• Only connect this unit to a mains socket with suitable trip and RCD protection.
• To disconnect from the mains socket, always remove by the mains plug. Do not attempt to remove by
pulling the mains cable.
• Disconnect the unit from the mains supply before cleaning. Cleaning should be carried out with a soft, dry
cloth.
• Do not submerge or expose this machine to any liquid.
• Do not operate near exposed water or in high humidity.
• Choose a suitable route for mains cables, ensuring trip hazards are avoided and the mains cable is not at
risk of being crushed.
• Do not open this unit to service. There are no user-serviceable parts inside. Any servicing or repairs should
be carried out by a qualified engineer only. Any attempt to service or adapt this unit will leave your
warranty void and could result in serious malfunction or in ury.
Protection from Fire:
• Do not place near sources of heat or ignition.
• Do not cover or block any ventilation holes.
• Check your AC wall socket will take the power you are applying to avoid overloading the mains supply.
Protecting Your Mac ine From Damage:
• Always install in a suitable location where vibrations to the unit are avoided.
• Check this unit matches the mains voltage and frequency before plugging it in to your mains socket.
• In the event that any ob ect or liquid enters the machine switch off immediately, remove from mains and

consult a qualified engineer.
• Should you experience any malfunction or damage to the mains cable, disconnect from the mains supply
immediately and consult a qualified engineer.
• All parts should be replaced with genuine spare parts and carried out by a qualified engineer.
• Do not add liquids of any kind, especially flammable liquids to this machine or its intended fluid. Use only
water based fluid, specifically designed for effects machines.
• Use high quality water-based liquid, recommended by your dealer to reduce clogging.
• During operation ensure there is sufficient fluid in the tank. Operating without fluid will damage the pump.
• If your machine fails to work disconnect immediately, remove all liquid and return in original packing to
your dealer.
• Always drain the fluid and water tanks before transporting.
• Follow the cleaning and maintenance advice in this manual.
• If your machine fails to work, disconnect immediately, remove all liquid and return in original packing to
your dealer.
Danger of Injury or Burns:
• For operation by adults only, ensure installation is away from the reach of children.
• Never leave the machine running unattended.
• Avoid all contact with the heater.
• Never aim the nozzle directly at people.
• Use only in a well ventilated area & do not cover the machine vents. In order to guarantee adequate
ventilation, allow a free air space of at least 20cm around all sides of the machine.
• Effects fluids can cause irritation and in ury, handle with care and keep out of the reach of children. Avoid
contact with the eyes and skin, if this occurs rinse with warm water. If ingested call a doctor immediately.
Before Use:
Before commencing setup check the machine has not been damaged in transit. In the event there is any
damage to the housing, cable or internal components contact your dealer immediately.
Specifications:
Code: PFX400SLED
Mains Supply: 240Vac 50Hz
Power: 400 Watts
Heat Up Time: 3 min
Dimensions: 230 x 110 x 110mm
Weight: 1.5kg
Features:
• 400 Watt heater.
• Amber LEDs
• 0.3L Fluid Tank.
• Wired remote control.
• Hanging Bracket

Description:
The PFX400S LED is a powerful smoke machine that can be floor mounted or hung from truss.
1. Heater Nozzle: Smoke output, will get very hot do not touch.
2. Fluid Tank: Fill the fluid tank with standard fog liquid, do not spill the liquid as this could damage the
electronics.
3. Hanging Bracket: Used for mounting to truss, always use a safety wire as secondary support.
4. Liquid Level: Fluid level reading, do not overfill.
5. Wire Controller: Is connected to the wired remote control
6. Power Switc : Used to turn the smoke machine on and off.
7. Fuse Holder: If this blows once, replace with the correct size fuse, if it blows again, there may be a problem
with the machine, seek professional help from an engineer.
8. Mains Lead: Connect this to a suitable mains supply (230Vac).
9. LEDS: Amber LEDs light up when smoke is emitting.
❶
❷
❷
❺
❼
❻
❸
❽❹
❸
❾

First Time Operation:
• Before you start using this unit, please check there is no transportation damage, should there be any, please
do not use the device and contact your dealer immediately.
• Put the smoke machine on a flat stable surface. Make sure no one can put any body part close to the heater
output.
• Unscrew the Lid on the fluid bottle, fill up with a suitable fog liquid, make sure not to over fill. Then screw
the plastic cap back on. Make sure the tank never runs dry during operation.
• Connect the PFX400S LED to a suitable mains supply.
• Allow the machine to warm up for about 3 minutes.
• The ready indicator light will light up, on the wired remote.
• The smoke machine is now ready to use.
• Press the switch to ON on the wired remote to operate.
• If the ready light goes out, the smoke machine needs to reheat before it will work again.
Over ead Rigging:
The installation must be carried out by a qualified engineer only. Improper installation can result in in uries or
damage to property. Overhead rigging requires experience. Working loads should be a heard to, certified
materials should be used. The installed device should be regularly inspected for safety.
• Make sure the working area is clear from people and obstructions during rigging, de-rigging and servicing.
• Locate the smoke machine in a well ventilated area away from flammable materials and liquids. The smoke
machine needs to be 50cm away from surrounding walls and fixtures.
• The smoke machine should be installed out of reach of people and not where people are seated, walking or
standing.
• When mounting make sure the installation point can take the weight.
• Make sure a safety chain or wire is always used and can take the weight of the smoke machine. This is a
secondary support, never rely on this for the primary support.
• The smoke machine should be well fixed and free from swinging.
• Do not cover any ventilation holes.
• Turn of the supply power off when the machine is not in use for an event.
• The operator must make sure the smoke machine has been installed correctly to all the necessary
guidelines before each use. The installation should be inspected every 6 months.
Maintenance:
• Do not allow liquid to become contaminated. Always replace the cap on the liquid container immediately
after filling.
• After every 40 hours of operation, or if the unit is not to be used for one month, It is recommended to run a
cleaning solution of 20% clear vinegar and 80% distilled water through the system to prevent clogging in the
heater. This should be carried out in a well-ventilated room.
• Always empty the fluid and water tanks after every use. Use a dry cloth to wipe down the outside of the
smoke machine. Make sure the power cable is disconnected from the mains supply.
• The mains cable must be in impeccable condition and should be replaced if a small defect is detected. All
other maintenance should be carried out by a qualified engineer.