Perlegear PGCS02 User manual

Model: PGCS02
Corner Shelf Instruction Manual
V1.0(A)
Thank you for choosing this Perlegear product! At Perlegear we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
Technical Support:
(US/CA)1-800-456-5231 Mon-Fri 8am - 8pm(CST)
(UK)44-808-196-4165 Mon-Fri 2pm - 10pm(UTC)
Other Info:
[email protected]

[Not Included]
• Check package contents against supplied parts and hardware list to assure that all
components were received undamaged. Do not use damaged or defective parts. lf you
require replacement parts, please contact our customer service at
[email protected].
• Carefully read all instructions before attempting installation. If you do not understand the
instructions or have any concerns or questions, please contact customer service at
[email protected].
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity of 22.05 lb (10KG). We can not be liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use. Thank you for your
understanding.
A X 1 B X 3
Step 1
C X 3
BC
Lag Screw
M3.5x40mm
Glass Shelf
Bracket
Insert the Lag Screw [D] into the Bracket [B]
S
Insert the lag screw [C] into the bracket [B].
Slightly loosen the set screw [S]
until it is flush with the bracket [B].
IMPORTANT SAFETY INFORMATION
Supplied Parts and Hardware
Tools Needed (Not lncluded)
Stud Finder Pencil Phillips
Screwdriver
Level Drill 5/64 in (2mm)
Wood Drill
15/64 in (6mm)
Concrete Drill Hammer
Wall Anchor
φ14x42mm
x3
D
CAUTION!
This wall anchor [D] is
for drywall ONLY. DO
NOT use them in
concrete / brick / wood
studs wall.
CAUTION!
This wall anchor [E] is
for concrete or brick
walls ONLY. DO NOT
use them in drywall or
wood studs.
x3
E
Wall Anchor
φ7x35mm
01 02 03 04 05 06

Step 2 Find the Proper Installation Location of the Glass Shelf
Before installation, please identify your wall type.
For wood stud installation, follow the step 2A.
For drywall installation,follow the step 2B.
For solid concrete and concrete block walls installation, follow the step 2C
Step 3 Secure the Brackets [B] on Wall
Step 3A For wood stud installation
Position and level the glass shelf [A] at
your desired height, then mark the holes
for brackets. Make sure each bracket is
installed in the installation range of the
glass shelf [A].
For wood stud mounting, wall
anchors [E] are not necessary.
WARNING:
X
E
3A-1
I
n
st
a
lla
t
i
o
n
R
ange
a2
a1
Ins
t
a
llat
i
o
n
Rang
e
a2
a1
OR
V2.0
a1a2
2
c
m(0.8in)Mi
d
po
i
nt
2cm(0.8in)2cm(0.8in)
b1
b2
There are total 3 brackets. Please
attach a brackets on one edge of
the glass shelf while attaching the
other two brackets to the other
edge.
To achieve the stability, make
sure each brackets is installed in
the in installable range of the
glass shelf.
The installable range:
The distance between a1 and a2;
The distance between b1 and b2.
01 02 03 04 05 06

[Not Included]
90 degree angle
A
a1
a2
I
nstall
a
ti
o
nRange
3A-3
3B-1
B
C
The bolt
points to
down
Phillips Screwdriver
Secure the brackets [B] on the wall
by tightening the lag screws [C]
using a phillips screwdriver.
Position and level the glass shelf [A] at
your desired height, then mark the
holes for brackets. Make sure each
brackets is installed in the in installable
range of the glass shelf.
3A-2
1 37/64 in (40mm)
5/64 in (ø2mm)
For wood studs,drill 2 pilot holes
using a 5/64 in (ø2mm) diameter
drill bit. Make sure the depth is not
less than 1 37/64 in (40mm).
For the drywall, screw the anchor
[D] into the drywall.
[Not Included]
Phillips Screwdriver
Step 3B For drywall installation
D
01 02 03 04 05 06

D B
CB
D
a1
a2
A
3B-2
3B-3
[Not Included]
Phillips Screwdriver
3C-1
Screw the anchor [D] into the drywall.
Secure the brackets [B] on the
wall by tightening the lag screws
[C] using a phillips screwdriver.
Installation Range
Position and level the glass
shelf [A] at your desired height,
then mark the holes for brack-
ets. Make sure each brackets is
installed in the in installable
range of the glass shelf.
The bolt
points to
down
Step 3C for solid concrete and concrete block walls installation
D
01 02 03 04 05 06

Secure the brackets [B] on the wall by tightening the lag screws [C]
using a phillips screwdriver.
C B
1 49/64 in (45mm)
9/32 in (ø7mm)
For Wall Anchor
Drill 3 pilot holes using a 9/32
in (ø7mm) diameter drill bit.
Make sure the depth is not
less than 1 49/64 in (45mm).
Use the hammer to knock
concrete anchors [E] into the
wall. Be sure the anchors [E]
are seated flush with the
concrete surface.
E
3C-2
3C-3
3C-4
E
01 02 03 04 05 06

Install the glass shelf [A] into the brackets. Tighten the bolt [S]
only until they are pulled firmly against the glass shelf. DO NOT
over-tighten the [S].
S
S
S
S
Secure the Glass Shelf [A] into the Brackets [B]
90 degree angle
A
Step 4
[Not Included]
Phillips Screwdriver
Note:
The product is designed for
showing the shiny side up.
01 02 03 04 05 06

Thank you again for
choosing this Perlegear product!
All of us at Perlegear do appreciate your product purchase. We hope that
you are as happy with your product as we designing and manufacturing it for
you. We strive to provide you with the best quality products and services in
the industry. If you have any questions please don't hesitate to contact us at
Technical Support:
(US/CA)1-800-456-5231 Mon-Fri 8am - 8pm(CST)
(UK)44-808-196-4165 Mon-Fri 2pm - 10pm(UTC)
Other Info:
[email protected]
01 02 03 04 05 06