PERMASTEEL PS-207 User manual

1
Permasteel 80QT Cooler
Use & Care Guide
Model number: PS-207, PS-207-80PE
Thank you for purchasing your new patio cooler from Permasteel.
We hope you enjoy your product.
If you have any questions, please call us 1-888-287-0735
or visit www.permasteel.life

2
Table of content
Important Information 2
Parts List 3
Hardware 4
Assembly Steps 5
Care & Maintenance 11
Limited Warranty Information 11
Important
Information
Thank you for your purchase of our Patio Cooler.
We sincerely hope you will enjoy using our fine
products.
•Please take time to read these instructions
thoroughly and follow each step carefully for
safe and easy operation.
•Please contact our customer service at
1-888-287-0735 if you have any questions.
•Please keep this manual for future reference.
CAUTION
1. Hand tools only, use of power tools could
damage product.
2. Remove all components, hardware and tools
from box before assembly. Inventory and
separate each of the hardware and
components included.
3. Please consider recycling all applicable
packaging material.

3
Parts List
Key Description Qty
A Lid Knob 2
B Lid 1
C Body Handle 2
D Body (Basin) 1
E Bottle Opener 1
F Bottle Cap Catcher 1
G Leg Frame 2
H Bottom Shelf 1
I Caster 2
J Caster with Brake 2
AA M6 x 13 Bolt 22
BB M6 x 15 Shoulder Bolt 2
CC M4 x 32 Screw 2
DD Flat Washer 4
EE Hex Nut 2
If you are missing any parts or have damaged
parts, please call 1-888-287-0735 M-F 8:00-5:00
Pacific Time. For replacement, visit us at
www.permasteel.life

4
Hardware
The following hardware is provided in a poly bag.
M6x13mm Bolt: 22 pcs
M6x15mm Shoulder Bolt: 2 pcs
M4X32mm Screw: 2 pcs (Note: Attached to lid knobs)
Flat Washer: 4 pcs
Hex Nut: 2 pcs
Tools Included:
Tools
The following tools are required for assembly:
•Allen wrench (provided)
•Open end wrench (provided)
•Hex wrench (provided)
•Phillips screwdriver (not provided)

5
Assemble Steps
Step 1
•Turn body (basin) upside down, place it on a clean, soft surface and attach 2 leg frames (G) to body (D)
with (6) M6x13mm bolts (AA), 3 bolts for each leg frame, with the provided Allen wrench.
Note: Do not fully tighten the bolts. Leg frames should be loose so that it can be aligned with the holes
on the bottom shelf.
Allen Wrench

6
Step 2:
•Attach the bottom shelf (H) to the leg frames (G) with (2) M6x13mm bolts (AA), (4) flat washers (DD),
and (2) hex nut (EE) with the provided hex wrench.
Note: Do not fully tighten the bolts. Leg frames and bottom shelf should be loose so that it can be
aligned with the holes for the casters.
Hex Wrench

7
Step 3
•Insert and thread casters (I) through the bottom panel holes and into leg frame using the provided
open end wrench.
•Insert and thread casters (J) through the bottom panel holes and into other leg frame using the
provided open end wrench.
Note: Leg frames and bottom shelf should be loose so that it can be aligned with the holes for the
casters.
•Now, tighten all the bolts left loose from step 1 & 2.
Open End Wrench

8
Step 4
•Attach the body handles (C) to body (D) using (12) M6x13mm bolts (AA), 6 bolts for each handle, and
tighten with the provided Allen wrench.
Allen Wrench

9
Step 5
•Attach the bottle opener (E) to body (D) using (2) M6x13mm bolts (AA) and tighten with the Allen
wrench.
•Attach the cap catcher (F) to body (D) using (2) M6x15mm shoulder bolts (BB).
Allen Wrench

10
Step 6
•Note: The lid knobs (A) are pre-attached to the lid (B). They are upside down.
•Please remove the knobs using a Phillips head screwdriver and re-assemble them on the lid
right-side up.