Pet Stop OT-100 User manual

Systems
Each Pet Stop®, Pet Fence System consists of a transmitter and at
least one receiver. The following pages will provide instruction on
the operation of each piece of equipment.
All Pet Stop, Pet Fence products are sold as a system, and, while Petstop.com may feature one or
more specific systems consisting of a particular transmitter and receiver, all our systems are
designed to be interchangeable so that each Dealer has the flexibility of providing the best solution
for your particular needs. Therefore, it is not uncommon for a Dealer to mix or match different
products in order to design the system that is the best fit for you and your pet.
Pet Stop is fortunate to have a network of Dealers who are experts in this field. Each one can be
relied upon to analyze and recommend solutions that are uniquely designed for you and your pet.
All the Pet Stop equipment incorporates a host of customizable settings to accommodate every
breed and every pet disposition. Your Dealer is trained in how to use these settings to attain a
smooth transition during training, and then finalizing those settings to ensure safe, comfortable and
reliable containment.
SYSTEMS
05Pet Stop | Owner’s Guide

Your transmitter comes complete with these standard features:
Remember: Do not allow your pet outside during a lightning storm.
Outdoor Transmitters
Traditionally, lightning is one of the most common causes of
transmitter failure. Pet Stop has developed built-in surge and
over-voltage protection for both the electrical outlet and any high
voltage carried by the buried wire in your yard.To add extra
protection for you and your pet, we have added Zapp Alert®, an
audio-visual indication feature should lightning damage your unit. If
your transmitter experiences an electrical surge, the transmitter will
continue to sound two short beeps. If this happens, contact your
local Pet Stop dealer for service immediately.
Built-in Lightning Protection with Zapp Alert® Warning
Your transmitter also has a built-in sensor which monitors the boundary wire. If, for any reason, the wire
becomes broken, the transmitter display will flash and a continuous single beep will alert you to the
problem. Unplug the transmitter and contact your local Pet Stop dealer to assist you in locating and
repairing the wire break correctly.
Wire Break Warning System
Your transmitter is also completely adjustable. Press the up and down buttons located on the front of
the transmitter to adjust the signal field for your specific installation. Please see ‘ADJUSTING SIGNAL
FIELD’ on page 7. The range displayed has a range from 01 to 32. For example, if your range is set to 16
this indicates there is 8 feet of signal field on either side of the boundary wire for a total of 16 feet.
Fully Adjustable Signal Field
OUTDOOR TRANSMITTERS
06Pet Stop | Owner’s Guide
Your Pet Stop dealer has set the signal field range appropriate for your
installation. Before adjusting the signal field width contact your dealer.
We recommend that your dog be on a leash or carefully supervised if the
transmitter is not functioning.

Your Pet Stop dealer has programmed your system specifically for your pets. Should you need to
modify the programming please consult your local Pet Stop dealer.
Transmitter Programming
OT-100, OT-150, & OT-200
Features
OT-100, OT-150, & OT-200
07
Pet Stop | Owner’s Guide
Digital Display
This display indicates the power level and will
blink if the boundary wire loop is broken or a
power surge has occurred.
Signal Field Adjustment
The signal field width is adjusted by pressing
the UP or DOWN buttons. See page 5 for
complete description.
Boundary Loop Connections
This is where the “loop” or boundary wire is
connected.
Ground Wire
A Ground Wire is also connected to the
electrical outlet.
AC Adapter
The AC adapter supplies the
power and plugs into your
electrical outlet.
To turn the transmitter off, simply unplug the transmitter from the
power jack.
Shown is the
OT-150 model. Also
applies to the
OT-100 & OT-200

Programming Buttons
The UP, DOWN and SET buttons are
used to program and make
adjustments to your system’s signal
field and stimulation settings.
Digital Display
Information concerning the signal field
width and collar settings are displayed
in the LED display area.
AC Adapter Jack
The AC adapter supplies the power and
plugs into your electrical outlet.
Boundary Loop Connections
This is where the “loop” or boundary
wire is connected. Ground Wire
A Ground Wire is also connected to
the electrical outlet.
OT-300
OT-300
Use the following steps to adjust the system’s signal field, or how far your pet can approach the buried wire.
Hold the SET BUTTON (Center) until the display turns off. Immediately RELEASE the SET button. The
current signal field setting will be displayed in the LED and two small red dots will be visible at the
bottom of the display indicating program mode.
Use the UP and DOWN arrow keys to adjust your boundary setting to your preferred boundary setting.
The range displayed has a range from 01 to 32.
For example, if your range is set to 16 this indicates there is 8 feet of signal field on either side of the
boundary wire for a total of 16 feet.
Press SET BUTTON when finished. The number will flash once to indicate a change has been made
and return to normal operation. If SET is not pushed, the programming mode will timeout after 40
seconds and return to the previous setting.
Adjusting the signal field
08Pet Stop | Owner’s Guide
Your Pet Stop dealer has programmed your system specifically for your pets. Should you need to
modify the programming please consult your local Pet Stop dealer.
1.
2.
3.
OT-300 Transmitter Programming
Features

We know pets inside and out. Our indoor transmitters bring the benefits of boundary setting indoors.
Our indoor transmitters can create either a wireless zone or be customized, using wire discretely
hidden.
We also offer a battery-powered indoor unit that can be used where no electrical outlets are available.
Applications vary but a few typical uses are in a waterproof enclosure to protect a garden or flower bed
outside or locating it behind a wall to protect a passageway.
Your local Pet Stop dealer is trained to recommend a variety of boundary configurations to meet your
particular needs.
Indoor Transmitters
INDOOR TRANSMITTERS
09Pet Stop | Owner’s Guide

Room Wizard
ROOM WIZARD
Digital Range Display readouts display
the current signal field range setting.
Power On/Off and Range Adjustment
Buttons. If the Range Display is not lit,
pressing the upper (“+“) button will turn
the transmitter on. Pressing both
buttons (”+” and “-”) at the same time
will turn the transmitter off.
Pressing the upper (”+”) button will
increase the signal field emanating
from the unit or wire if used. This will
effectively increase signal around
the unit or on both sides of the wire
if in a wired configuration. Pressing
the lower (”-”) button will decrease
this area.
10
Pet Stop | Owner’s Guide
Features
The RoomWizard can be use either as a wireless unit or can be used with wire to create a specific
boundary. Consult your local Pet Stop dealer for suggestions on how best to used the RoomWizard.
AC Adapter Power
Connector. Plug in the AC
adapter that came with
the unit, into the “Power”
connector on the left.
Only use an approved
PET STOP® AC adapter.
Wired Mode Adapter Cord
Connector. When using
the transmitter with
boundary wire, plug in the
Wired Mode adapter cord
at the right connector
labeled “Loop”.

Room Wizard
Operation
Your Pet Stop RoomWizard can be set up in your home either as wireless or a wired system, depending on the
needs of you and your pet.
Pet Stop RoomWizard – Wireless Operation
Place the RoomWizard unit in the location you want your pet to avoid. For example, if you do not want your pet
to jump on the sofa, place the unit under the sofa. The RoomWizard can also be permanently mounted on a
wall using the key hole slot on the bottom of the transmitter case.
Under normal operation, the RoomWizard will display the signal field strength number (such as “10”) and will
make no sounds. This indicates the RoomWizard is operating normally. You can make adjustments to the
signal field range to achieve the correction zone you desire. Pressing the upper button (”+”) will increase the
signal field to a maximum of 32. Pressing the lower button (”-”) will decrease the signal field to a minimum of 1.
Plug the AC adapter into an AC electrical outlet.
Plug the other end of the AC adapter into the LEFT connector on the RoomWizard marked
“Power” as shown in photo below.
The Range display should be lit to indicate the RoomWizard is on. If the range display is
not lit, press the top Range Adjustment button to turn the unit on.
Adjust the signal field range by pushing the upper button (+) to increase the range and the
lower button (–) to decrease the range.
Test the signal field range by using the receiver collar and listening for the beeps.
To turn on the RoomWizard unit:
11
Pet Stop | Owner’s Guide
1.
2.
4.
5.
3.
Remember: Always remove your pet’s Pet Stop receiver collar before
making any adjustments to the signal field range.