Phanteks Glacier G1080 User manual

P h a n te k s G lacier G 1 0 8 0
PACKAGE CONTENTS
Glacier G1080 Water Block
(GIGABYTE GTX 1080 G1 Gaming )
QTY: 1
Thermal Pads
QTY: 3
Description:
For applying on circuit board on GPU
INSTALLATION
Remove all highlighted screws. All heat sink assembly screws should be removed,
including self-adhesive washers on both sides of the PCB (if present).
DISCLAIMER -This product is intended for advanced users. Please
-
have been made to provide the most comprehensive information
possible, Phanteks assumes no liability expressed or implied for
any damage(s) occurring to your components as a result of using
Phanteks cooling products, either due to mistake or omission on
our part in the below instructions, or due to failure or defect in the
Phanteks cooling products.
WARNING -
body’s static electric charge by touching a grounded surface – for
example, the metal surface of the power supply or chassis – before
performing any hardware procedure. Phanteks assumes no liability
for any damage, caused directly or indirectly, by improper installation
of any components. If you do not feel comfortable with performing
*Please do not disassemble the water block. Warranty will be voided.
Thermal Compound (PH-NDC_01)
QTY: 1 Phanteks Plugs
QTY: 2
Phanteks RGB Cable
QTY: 1
PH-GB1080GB_BK01/CR01
M2.5x5
QTY: 11 (spare 4 pcs.)
INSTALLATION GUIDE
GIGABYTE G1 GAMING
STEP 1. REMOVING STOCK COOLER
LIGHTLY COAT NVIDIA GPU CHIPWITH ENCLOSEDTHERMAL PASTE.
STEP 2. APPLYING THERMAL COMPOUND
Wipe o the remains of the original thermal compound until components and
Circuit board are completely clean (we recommend using a isopropanol
cleaning pad). Apply a light coat (see image) of the PH-NDC_01 thermal paste.
TAKE OUT THE TOP EVA-FOAM LAYER FROM THE BOX TO USE AS BASE FOR YOUR GPU PLACEMENT.
MAKE SURE TO UNPLUG THE FAN AND RGB LED CABLES WHEN YOU REMOVE THE HOUSING.
Phanteks RGB Cable for Phanteks Case
QTY: 1

STEP 4. CONNECTING THE RGB LED
Make sure to connect the RGB LED cable from the waterblock to the GPU PCB
RGB Header. (see illustration)
STEP 5. PLACING THE BLOCK ON TO THE GRAPHICS CARD
STEP 6. INSTALLATION OF FITTINGS AND TUBING
STEP 3.
PLACING THERMAL PADS ON PCB
Place thermal pads on the circuit board as shown on the picture below. Refer to
numbering in previous picture when applying thermal pads of dierent sizes or
thickness. Phanteks made sure to provide customers with more than adequate
quantity of thermal pads to complete this step.
FOR THERMAL PAD 2& 3, ADJUST AND CUT LENGTH
ACCORDING TO GPU VDD VRM CHIPS/MOSFET CHIPS.
f
for V
or memory IC
dd VRM
2
1 1 1 1 1 1 1 1
3
for Vdd MOSFET
Position 1: 16 x 13 x 0.75mm
Position 2: 10 x 90 x 0.75mm
Position 3: 20 x 90 x 1.25mm
Optional Upgrade
Sync the lighting with a Phanteks case / RGB Motherboard using the Phanteks upgrade kit
(not included).
Carefull y position the water block onto the graphics card. During this process
please make sure you align mounting holes on the PCB with holes on the
water block.
Once the water block is in place, plug in the remaining RGB LED cable
connector to the water block as shown in the illustration.
Screw in the two G1/4 threaded male ttings, attach the liquid cooling tubes
and connect the water block(s) into the cooling circuit. Phanteks recommends
Phanteks ttings with the Phanteks Glacier Series water blocks.
DO NOT FORGET TO PLUG THE REMAINING TWO OPENING.
FOR BEST PERFORMANCE, WE RECOMMEND TO MATCH THE INLET/OUTLET
using
CONFIGURATION OF THE WATERBLOCK.
OUTIN
DO NOT USETOO MUCH FORCE BY PRESSING THE BLOCK DOWN TO THE PCB. CHIP DIES
ARE
MAKE SURE TO LAY THE GPU WITH WATER BLOCK FLAT DOWN WITHOUT RESTING ON
THE PCI.
PRONE TO CRACKING.
Use the included 7x M2.5x5 screws and washers (shown in blue) to
tighten the block to the GPU core.