Phanteks Eclipse Series User manual

FRONT I/O
FANS & RADIATORS CLEARANCES
PRODUCT OVERVIEW
ECLIPSE series
REAR
FRONT
TOP
120
FAN
140
FAN
140
FAN
120
FAN
120
FAN
140
RAD
120
RAD
120
RAD
120
RAD
CLEARANCE
CPU Cooler Height 160mm
PSU Clearance 250mm
GPU Clearance 400mm
E-ATX Motherboard 280mm
140
280
120
240
120
240
120
Max 122x315mm
*max motherboard compo-
nent height is 38mm
Max 142x315mm
Installation guide for:
Eclipse P360 models
Eclipse P418 models
22x Motherboard
+ SSD Screw
1x Motherboard-
Stando
FRONT FILTER
TOP FILTER
PSU FILTER
2x Thumb Screw
4x PSU Screw
12x Fan Screw
1x This Manual
6x Zip Tie
2x 120 mm
D-RGB Case fan
2x 2.5” SSD Bracket
(Pre-Installed)
INTRODUCTION INCLUDED ACCESSORIES
INSTALLATION GUIDE V1.0
Thank you for choosing Phanteks. Please take a moment
to carefully go through the manual. Phanteks will not take
responsibility for any damages incurred due to incorrect
installation or usage of this product.
1. Power Button
4. USB 3.0
2. Headphone
6. D-RGB Mode
5. D-RGB Color
3. Microphone
English
1. Power Button
2. Headphone
3. Microphone
4. USB 3.0
5. D-RGB Color
6. D-RGB Mode
Francais
1. Bouton d’alimentation
2. Casque
3. Microphone
4. USB 3.0
5. D-RGB Couleur
6. D-RGB Mode
Deutch
1. Ein-/Austaste
2. Kopfhörer
3. Mikrofon
4. USB 3.0
5. D-RGB Farbe
6. D-RGB Modus
Espanol
1. Botón de encendido
2. Auricular
3. Micrófono
4. USB 3.0
5. D-RGB Color
6. D-RGB mode
For PH-EC360A_DBK model, other models may vary

PANEL REMOVAL
1. 1.
1.
2.
2.
1. 1.
1.
2.
2.
LOOSEN THUMB SCREWS AND
SLIDE PANEL TO THE REAR
REMOVE FRONT PANEL BY PULLING ON
THE PANEL FROM BELOW
LOOSEN THUMB SCREWS
SLIDE SIDE PANEL OFF
REMOVE TEMPERED GLASS PANEL
There are three panels which can be removed from the P360A Chassis; the left side tempered
glass panel, the right side panel and the front panel. Follow these steps below.
2x
LOOSEN:
LEFT SIDE PANEL
FRONT PANEL
RIGHT SIDE PANEL
2x
LOOSEN:
ECLIPSE series

9x
4x
4x
The HDDTray can
also hold a 2.5”SSD.
HARDWARE INSTALLATION
MOTHERBOARD
POWER SUPPLY
2.5” SSD
3.5” HDD
1
2
3
1.
1.
1.
2.
INSTALL THE MOTHERBOARD USING THE MOTHERBOARD SCREWS.
INSTALL THE POWER SUPPLY WITH 4X PSU SCREWS.
INSTALL THE SSD WITH 4X SSD SCREWS AND PLACE IT ON THE 4X RUBBER GROMMETS.
INSTALL THE HDD IN THE BRACKET AND PLACE IT IN THE CHASSIS.
2
1
ECLIPSE series

ECLIPSE series
CABLE CONNECTION
With the Integrated Digital-RGB controller, you can choose from a variety of modes and color options.
The P360 / P418 Chassis supports the Phanteks Vertical GPU
bracket. It can be easily installed in the PCI slot area. Follow the
instructions that are included with the Vertical GPU bracket.
Power SW
HD
AUDIO
USB 3.0
SATA
DIGITAL-RGB CONTROL
OPTIONAL UPGRADES
CONNECT TO DIGITAL-RGB PRODUCTS
VERTICAL UPGRADE (PH-VGPUKT_02)
CONNECT TO MOTHERBOARD
CONNECT TO POWER SUPPLY
TO DIGITAL-RGB PRODUCTS
TO DIGITAL-RGB MOTHERBOARD
COMPATIBLE WITH:
Connect to compatible motherboard for
software control. See the below section:
Digital-RGB Control.
COLORS
2 SEC
MODES
SOLID
BREATHING
RADAR
SPARKLE
RAINBOW
PRESS AND HOLD THE MODE BUTTON TO TURN OFF FRONT LEDS
PRESS AND HOLD THE MODE BUTTON AGAIN TO TURN OFF ALL LEDS
SOFTWARE CONTROL:Turning o all LED’s will allow
for software control with a compatible motherboard.
The Mode & Color buttons do not function when
using Software Control.
MAXIMUM POWER: The Digital-RGB controller can
provide a maximum of 7A of power for expansion.
D-RGB Mode
D-RGB Color