Phanteks ECLIPSE P300 User manual

STEP 8.
STEP 9.
CLEARANCE
CPU Cooler Height 165 mm
PSU Clearance 200 mm
GPU Clearance 355 mm
Front radiator | 240:
Front radiator | 280:
122x315 mm
142x315 mm
REAR
120
FAN
TOP
120
FAN
140
FAN
140
RAD
FRONT
120
FAN
120
RAD
120
RAD
English
1. Headphone
2. Microphone
3. USB 3.0
4. RGB Control
5. Power Button
6. Reset Button
Francais
1. Casque
2. Microphone
3. USB 3.0
4. RGB Contrôle
5. Bouton d’alimentation
6. Bouton de réinitialisation
Deutch
1. Kopfhörer
2. Mikrofon
3. USB 3.0
4. RGB Steurung
5. Ein-/Aus Schalter
6 .Reset-Knopf
Espanol
1. Auricular
2. Micrófono
3. USB 3.0
4. RGB Controlar
5. Botón de encendido
6. Botón de reinicio
Thank you for choosing Phanteks. Please take a moment
to carefully go through the manual. Phanteks will not
take responsibility for any damages incurred due to
incorrect installation or usage of this product.
This manual is applicable for the following products:
PH-EC300PTG
PH-EC300ATG
ECLIPSE P300A FRONT I/O
ECLIPSE P300 FRONT I/O
INTRODUCTION INCLUDED ACCESSORIES
Eclipse P300 / Eclipse P300A
120 mm Black Fan
(Pre-Installed)
2.5” SSD Bracket
(1x Pre-Installed)
5x PSU Screw
12x Fan Screw
1x This Manual
6x Zip Tie18x Motherboard
+ SSD Screws
1x Motherboard
Stando
PRODUCT OVERVIEW
ECLIPSE P300 / P300A INSTALLATION GUIDE V1.0
1. Headphone
2. Microphone
3. USB 3.0
4. RGB Control
5. Power Button
140
FAN
ECLIPSE P300 / P300A INSTALLATION GUIDE V1.0
1. Headphone
2. Microphone
3. USB 3.0
6. Reset Button
5. Power Button
CABLE CONNECTION
OPTIONAL UPGRADES
VERTICAL GPU BRACKET
(PH-VGPUKT-02)
MOTHERBOARD CONNECTIONS
MOTHERBOARD
RGB HEADER
12V G R B
12V
COMPATIBLE WITH:
RGB LIGHTING  P300 ONLY
Diagram is a general overview. For a more accurate
overview of your motherboard, please consult that
motherboards’ manual.
POWER
LED
POWER
SWITCH
NOT USED
HDD
LED
RESET
SWITCH
Power LED
Solid
Breathing
Color Cycle
Short Press to change color:
Long Press to change mode:
Press and Hold to turn o or
switch to motherboard control.
RGB CONTROLS (P300 MODEL)
FRONT I/O FEATURES
HD AUDIO & USB 3.0 CABLES
a. CONNECT THE CABLES TO THE MOTHERBOARD
FRONT I/O HEADER CONNECTIONS
b. CONNECT THE CABLES TO THE FRONT I/O HEADER ON THE
MOTHERBOARD
(SEE FRONT I/O HEADER DIAGRAM FOR GENERAL REFERENCE)
CONNECT MORE RGB PRODUCTS
b. CONNECT RGB CONNECTOR TO RGB PRODUCTS c. CONNECT MOTHERBOARD RGB ADAPTER* TO THE MOTHERBOARD
*SOLD SEPERATELY (PH-CB_RGB4P)
SYNC YOUR CASE LIGHTING TO THE MOTHERBOARD
THE PHANTEKS VERTICAL GPU
BRACKET CAN BE EASILY
INSTALLED IN THE REAR PCISLOT
AREA WITHOUT MODIFICATIONS.
FOLLOW THE INSTRUCTIONS THAT
COME WITH THE VERTICAL GPU
BRACKET.
BOTH MODELS P300 / P300A
MOTHERBOARD FRONT I/O
HEADER DIAGRAM
P300A MODEL ONLY
SATA
a. CONNECT THE SATA CABLE TO THE POWER SUPPLY
(P300A DOESN’T COME WITH RBG CONTROL)
3.5” HDD Tray
(2x Pre-Installed)

HARDWARE INSTALLATION
MOTHERBOARD
INSTALL:
9x
INSTALL:
4x
INSTALL:
4x
INSTALL THE ATX MOTHERBOARD WITH 9 MOTHERBOARD SCREWS
POWER SUPPLY
INSERT THE POWER SUPPLY INTO THE CHASSIS
STEP 1.
STEP 4.
STEP 5.
STEP 6.
STEP 7.
STEP 2. STEP 3.
AND THEN SECURE THE POWER SUPPLY WITH 4 PSU SCREWS
2.5” SSD
INSTALL THE SSD DRIVE WITH 4 SSD SCREWS AND
MOUNT INTO THE CHASSIS.
A SECOND OPTIONAL SSD BRACKET CAN BE INSTALLED.
2.5” SSD DRIVES CAN ALSO BE INSTALLED INTO THE 3.5” DRIVE BAYS.
3.5” HDD
REMOVE THE HDD TRAY BY PULLING OUTWARD. INSTALL THE HDD
DRIVE IN THE TOOLLES HDD TRAY AND SLIDE THE MOUNTED
HDD TRAY BACK INTO THE CHASSIS.
The HDD Tray can also
hold a 2.5” SSD
If installing a Micro-ATX
motherboard, install the extra
stando supplied and consult your
motherboard manual for further
instructions.
ECLIPSE P300 / P300A INSTALLATION GUIDE V1.0
There are three panels that can be removed from the P300(A) Chassis; the left side
tempered glass panel, the right side panel and the front panel. Follow these steps below.
LEFT SIDE PANEL
a. LOOSEN THUMB SCREWS AND
SLIDE TO THE LEFT.
FOLLOW STEPS IN REVERSE ORDER.
RIGHT SIDE PANEL
LOOSEN THUMB SCREWS AND SLIDE
THE SIDE PANEL OFF.
FRONT PANEL
REMOVE FRONT PANEL BY PULLING
ON IT FROM BELOW
b. TILT PANEL FORWARD. c. PULL UPWARD TO REMOVE.
LOOSEN:
2x
ECLIPSE P300 / P300A INSTALLATION GUIDE V1.0
With the P300 model you can access the
dust lters after removing the front panel.
We recommend to clean the dust lters every
month for optimal performance.
Micro - ATX
PANEL RE-INSTALLATION
panel removal
LOOSEN:
2x